Date: Mon, 29 Jan 2001 14:35:04 -0800 From: "Kevin Oberman" <oberman@es.net> To: mobile@freebsd.org Subject: Trying not to Plug-N-Play Message-ID: <200101292235.f0TMZ4L03610@ptavv.es.net>
next in thread | raw e-mail | index | archive | help
--Multipart_Mon_Jan_29_14:34:25_2001-1
Content-Type: text/plain; charset=US-ASCII
Since PNP tends to mess up audio on my IBM 600E, I am manually
configuring the audio port and have disabled PNPBIOS in the
kernel. This does the trick for the sound system, but it breaks my
parallel port. The probe now reports:
ppc0: cannot reserve I/O range
Is there a way to get to my parallel port without PNP?
I am attaching my dmesg and kernel configurations.
R. Kevin Oberman, Network Engineer
Energy Sciences Network (ESnet)
Ernest O. Lawrence Berkeley National Laboratory (Berkeley Lab)
E-mail: oberman@es.net Phone: +1 510 486-8634
--Multipart_Mon_Jan_29_14:34:25_2001-1
Content-Type: application/octet-stream
Content-Disposition: attachment; filename="dmesg"
Content-Transfer-Encoding: 7bit
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.2-STABLE #12: Mon Jan 29 14:23:22 PST 2001
root@puppeteer.es.net:/scratch/src/sys/compile/THINKPAD
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (363.96-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x66a Stepping = 10
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 201129984 (196416K bytes)
config> en apm0
config> q
avail memory = 192712704 (188196K bytes)
Preloaded elf kernel "kernel" at 0xc02fa000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc02fa09c.
Pentium Pro MTRR support enabled
md0: Malloc disk
apm0: <APM BIOS> on motherboard
apm: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <NeoMagic MagicMedia 256AV SVGA controller> at 0.0 irq 11
pcic-pci0: <TI PCI-1251 PCI-CardBus Bridge> mem 0x50102000-0x50102fff irq 11 at device 2.0 on pci0
pcic-pci0: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][CSC parallel isa irq]
pcic-pci1: <TI PCI-1251 PCI-CardBus Bridge> mem 0x50101000-0x50101fff irq 11 at device 2.1 on pci0
pcic-pci1: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][CSC parallel isa irq]
pci0: <unknown card> (vendor=0x1013, dev=0x6001) at 6.0 irq 11
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xfcf0-0xfcff at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 7.2 irq 11
chip1: <Intel 82371AB Power management controller> port 0xefa0-0xefaf at device 7.3 on pci0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
pcm0: <CS4236> at port 0x52c-0x533 irq 5 drq 1 flags 0xa110 on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
pcic0: <Intel i82365> at port 0x3e0 iomem 0xd0000 irq 10 on isa0
pcic0: management irq 10
pccard0: <PC Card bus -- kludge version> on pcic0
pccard1: <PC Card bus -- kludge version> on pcic0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: cannot reserve I/O port range
pccard: card inserted, slot 1
ata1-slave: ata_command: timeout waiting for intr
ata1-slave: identify failed
ad0: 11509MB <IBM-DARA-212000> [24944/15/63] at ata0-master UDMA33
acd0: DVD-ROM <TOSHIBA DVD-ROM SD-C2102> at ata1-master using PIO4
Mounting root from ufs:/dev/ad0s2a
xe0 at port 0x240-0x24f iomem 0xd0000-0xd0fff irq 9 slot 1 on pccard1
xe0: Xircom CE3, bonding version 0x45, 100Mbps capable
xe0: DingoID = 0x444b, RevisionID = 0x1, VendorID = 0
xe0: Ethernet address 00:10:a4:f0:70:2f
xe0: watchdog timeout; resetting card
--Multipart_Mon_Jan_29_14:34:25_2001-1
Content-Type: application/octet-stream
Content-Disposition: attachment; filename="THINKPAD"
Content-Transfer-Encoding: 7bit
#
# THINKPAD -- IBM ThinkPad machine with WD/AHx/NCR/BTx family disks
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
# http://www.freebsd.org/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.ORG/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ./LINT configuration file. If you are
# in doubt as to the purpose or necessity of a line, check first in LINT.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.143.2.24 1999/12/05 01:56:42 luoqi Exp $
machine "i386"
#cpu "I386_CPU"
#cpu "I486_CPU"
#cpu "I586_CPU"
cpu "I686_CPU"
ident THINKPAD
maxusers 32
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
#options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options MFS #Memory Filesystem
options MD_ROOT #MD is a potential root device
#options NFS #Network Filesystem
#options NFS_ROOT #NFS usable as root device, "NFS" req'ed
options MSDOSFS #MSDOS Filesystem
options "CD9660" #ISO 9660 Filesystem
options "CD9660_ROOT" #CD-ROM usable as root. "CD9660" req'ed
options PROCFS #Process filesystem
options "COMPAT_43" #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=15000 #Be pessimistic about Joe SCSI device
options UCONSOLE #Allow users to grab the console
#options FAILSAFE #Be conservative
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) syscall trace support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
#options PNPBIOS #To support sound
options P1003_1B #Posix P1003_1B real-time extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options SOFTUPDATES #Enable soft updates
#options USER_LDT # Use this for wine
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O
# Optionally these may need tweaked, (defaults shown):
#options NCPU=2 # number of CPUs
#options NBUS=4 # number of busses
#options NAPIC=1 # number of IO APICs
#options NINTR=24 # number of INTs
device isa
#device eisa
device pci
# Floppy drives
device fdc0 at isa? port "IO_FD1" irq 6 drq 2
device fd0 at fdc0 drive 0
#device fd1 at fdc0 drive 1
# IDE controller and disks
#options "CMD640" # work around CMD640 chip deficiency
#device wdc0 at isa? port "IO_WD1" bio irq 14
#device wd0 at wdc0 drive 0
#device wd1 at wdc0 drive 1
#
#device wdc1 at isa? port "IO_WD2" bio irq 15
#device wd2 at wdc1 drive 0
#device wd3 at wdc1 drive 1
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
#device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
#device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
#options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI devices
#device acd0 #IDE CD-ROM
#device wfd0 #IDE Floppy (e.g. LS-120)
# SCSI Controllers
# A single entry for any of these controllers (ncr, ahb, ahc) is
# sufficient for any number of installed devices.
#controller ncr0 # NCR/Symbios Logic
#controller ahb0 # EISA AHA1742 family
#controller ahc0 # AHA2940 and onboard AIC7xxx devices
#controller amd0 # AMD 53C974 (Teckram DC-390(T))
#controller isp0 # Qlogic family
#controller dpt0 # DPT Smartcache - See LINT for options!
#controller adv0 at isa? port ? cam irq ?
#controller adw0
#controller bt0 at isa? port ? cam irq ?
#controller aha0 at isa? port ? cam irq ?
#controller aic0 at isa? port ? cam irq ?
# SCSI peripherals
# Only one of each of these is needed, they are dynamically allocated.
#controller scbus0 # SCSI bus (required)
#device da0 # Direct Access (disks)
#device sa0 # Sequential Access (tape etc)
#device cd0 # CD
#device pass0 # Passthrough device (direct SCSI)
# Proprietary or custom CD-ROM Interfaces
#device wt0 at isa? port 0x300 bio irq 5 drq 1
#device mcd0 at isa? port 0x300 bio irq 10
#device matcd0 at isa? port 0x230 bio
#device scd0 at isa? port 0x230 bio
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# Audio driver
device pcm0 at isa? port 0x52c irq 5 drq 1 flags 0x10
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa?
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa? tty
#options XSERVER # support for X server
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? # Advanced Power Management
# PCCARD (PCMCIA) support
device card
device pcic0 at isa? irq 10 port 0x3e0 iomem 0xd0000
# device pcic0 at isa?
device pcic1 at isa? irq 11 port 0x3e2 iomem 0xd4000 disable
# Serial (COM) ports
device sio0 at isa? port "IO_COM1" flags 0x10 irq 4
device sio1 at isa? port "IO_COM2" irq 3
#device sio2 at isa? disable port "IO_COM3" irq 5
#device sio3 at isa? disable port "IO_COM4" irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
#device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da0
# PCI Ethernet NICs.
#device de # DEC/Intel DC21x4x (``Tulip'')
#device fxp # Intel EtherExpress PRO/100B (82557, 82558)
#device tx # SMC 9432TX (83c170 ``EPIC'')
#device vx # 3Com 3c590, 3c595 (``Vortex'')
#device wx # Intel Gigabit Ethernet Card (``Wiseman'')
# PCI Ethernet NICs that use the common MII bus controller code.
#device miibus # MII bus support
#device dc # DEC/Intel 21143 and various workalikes
#device rl # RealTek 8129/8139
#device sf # Adaptec AIC-6915 (``Starfire'')
#device sis # Silicon Integrated Systems SiS 900/SiS 7016
#device ste # Sundance ST201 (D-Link DFE-550TX)
#device tl # Texas Instruments ThunderLAN
#device vr # VIA Rhine, Rhine II
#device wb # Winbond W89C840F
#device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# ISA Ethernet NICs.
#device ed0 at isa? port 0x280 irq 10 iomem 0xd8000
#device ep
#device ex
#device fe0 at isa? port 0x300 net irq ?
#device le0 at isa? port 0x300 net irq 5 iomem 0xd0000
#device lnc0 at isa? port 0x280 net irq 10 drq 0
#device cs0 at isa? port 0x300 net irq ?
# requires PCCARD (PCMCIA) support to be activated
device xe
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attatement needed
# and resources will always be dynamically assigned by the pccard code.
device wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those paremeters here.
device an
# The probe order of these is presently determined by i386/isa/isa_compat.c.
#device ie0 at isa? port 0x300 irq 10 iomem 0xd0000
#device fe0 at isa? port 0x300
#device le0 at isa? port 0x300 irq 5 iomem 0xd0000
#device lnc0 at isa? port 0x280 irq 10 drq 0
#device cs0 at isa? port 0x300
#device sn0 at isa? port 0x300 irq 10
# Pseudo devices - the number indicates how many units to allocated.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
#pseudo-device sl 1 # Kernel SLIP
#pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif 4 # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# USB support
#device uhci # UHCI PCI->USB interface
#device ohci # OHCI PCI->USB interface
#device usb # USB Bus (required)
#device ugen # Generic
#device uhid # "Human Interface Devices"
#device ukbd # Keyboard
#device ulpt # Printer
#device umass # Disks/Mass storage - Requires scbus and da
#device ums # Mouse
# USB Ethernet, requires mii
#device aue # ADMtek USB ethernet
#device cue # CATC USB ethernet
#device kue # Kawasaki LSI USB ethernet
--Multipart_Mon_Jan_29_14:34:25_2001-1--
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200101292235.f0TMZ4L03610>