Date: Sat, 22 Jul 2000 13:16:49 -0700 From: "David O'Brien" <obrien@FreeBSD.ORG> To: Matthew Jacob <mjacob@feral.com> Cc: alpha@FreeBSD.ORG Subject: Re: 4.1-20000719-RC#2 Message-ID: <20000722131648.E44856@dragon.nuxi.com> In-Reply-To: <Pine.BSF.4.05.10007211228120.8451-100000@semuta.feral.com>; from mjacob@feral.com on Fri, Jul 21, 2000 at 12:30:00PM -0700 References: <14712.41758.459790.390526@grasshopper.cs.duke.edu> <Pine.BSF.4.05.10007211228120.8451-100000@semuta.feral.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Fri, Jul 21, 2000 at 12:30:00PM -0700, Matthew Jacob wrote:
> I think you need to put into RELNOTES that Alpha 4100 isn't supported.
More testing. Using the CDROM that boots fine on my Miata(MX5) on the
4100, I find that the CDROM isn't accessable from the loader. Even doing
an ``ls'' from the loader hangs. Note that this has always worked on my
Miata (even with the current /boot/cdboot rather than the 4.0-R one).
This behavior seems the same with floppies. So for some reason the
loader is unable to access any of our bits from the installation media
[in the non-harddisk case].
P00>>>boot dka500
Initializing...
SROM V2.0 on cpu0
SROM V2.0 on cpu1
XSROM V5.3 on cpu0
XSROM V5.3 on cpu1
BCache testing complete on cpu0
BCache testing complete on cpu1
mem_pair0 - 512 MB
20..20..21..21..23..
please wait 12 seconds for T24 to complete
24..24..
Memory testing complete on cpu1
Memory testing complete on cpu0
starting console on CPU 0
sizing memory
0 512 MB EDO
starting console on CPU 1
probing IOD1 hose 1
bus 0 slot 1 - NCR 53C810
bus 0 slot 2 - DECchip 21140-AA
probing IOD0 hose 0
bus 0 slot 1 - PCEB
probing EISA Bridge, bus 1
bus 0 slot 2 - S3 Trio64/Trio32
bus 0 slot 4 - PCI-PCI Bridge
probing PCI-PCI Bridge, bus 2
bus 2 slot 0 - QLogic ISP1020
** keyboard error **
configuring I/O adapters...
ncr0, hose 1, bus 0, slot 1
tulip0, hose 1, bus 0, slot 2
floppy0, hose 0, bus 1, slot 0
isp0, hose 0, bus 2, slot 0
System temperature is 30 degrees C
AlphaServer 4100 Console V5.3-1, 27-OCT-1998 11:16:38
CPU 0 booting
(boot dka500.5.0.1.1)
block 0 of dka500.5.0.1.1 is a valid boot block
reading 356 blocks from dka500.5.0.1.1
bootstrap code read in
Building FRU table
base = 200000, image_start = 0, image_bytes = 2c800
initializing HWRPB at 2000
initializing page table at 1f2000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Console: SRM firmware console
VMS PAL rev: 0x4001200010113
OSF PAL rev: 0x4001a00020115
Switch to OSF PAL code succeeded.
FreeBSD/alpha SRM CD9660 boot, Revision 0.1
(jkh@beast.freebsd.org, Mon Mar 20 21:08:56 GMT 2000)
Memory: 524288 k
> echo \007\007
> autoboot 10
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [kernel] in 6 seconds...
Type '?' for a list of commands, 'help' for more detailed help.
ok ls -l
<HANGS for minutes>
failed to send Read to dka500.5.0.1.1
halt code = 7
pcb 0
!!! Console entry context is not valid - Reset the system !!!
Brk 0 at 0006621C
0006621C ! BPT
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-alpha" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20000722131648.E44856>