Date: Tue, 01 Aug 2000 23:20:56 -0600 From: Brett Glass <brett@lariat.org> To: Darryl Okahata <darrylo@soco.agilent.com> Cc: Mike Smith <msmith@FreeBSD.ORG>, Greg Lehey <grog@lemis.com>, Jay Kuri <jay@oneway.com>, hardware@FreeBSD.ORG Subject: Re: FreeBSD on Dell Inspiron Message-ID: <4.3.2.7.2.20000801231512.046c0650@localhost> In-Reply-To: <200008020116.SAA15805@mina.soco.agilent.com> References: <Your message of "Tue, 01 Aug 2000 15:43:42 MDT." <4.3.2.7.2.20000801154059.04c50b80@localhost>
next in thread | previous in thread | raw e-mail | index | archive | help
At 07:16 PM 8/1/2000, Darryl Okahata wrote:
> Whatever you have, it's not an Inspiron 7500-clone. The sound on
>the 7500 uses only one IRQ (#5).
>
> You could try using polling mode for the pcic. That should free up
>IRQ 10. Also, go into the BIOS and disable everything that you don't
>use. On my 7500, I've disabled the IR port and the parallel port.
>
> You also haven't provided a (verbose, preferably) dmesg, which is
>pretty much mandatory if you want help for these problems.
Here's a dmesg. Note that I've forced the pcic to IRQ 9. The default was
10, and since 5 and 11 are committed (5 to the sound card, 11 to video)
leaving it at 10 would leave no IRQ for ep0. In short, if I did the
standard install from floppies, the machine couldn't allocate an IRQ
for the Ethernet card and therefore couldn't complete the install.
I don't understand why it's so restrictive about the IRQs it will
allow to be used for PCMCIA.
--Brett
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1-RELEASE #0: Thu Jul 27 04:44:16 GMT 2000
root@usw4.freebsd.org:/usr/src/sys/compile/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (497.84-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x681 Stepping = 1
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,XMM>
real memory = 67043328 (65472K bytes)
config> di sio1
config> di sn0
config> di lnc0
config> di le0
config> di ie0
config> di fe0
config> di cs0
config> di bt0
config> di aic0
config> di aha0
config> di adv0
config> en pcic0
config> po pcic0 0x3e0
config> ir pcic0 9
config> iom pcic0 0xd0000
config> f pcic0 0
config> en ed0
config> po ed0 0x280
config> ir ed0 10
config> iom ed0 0xd8000
config> f ed0 0
config> q
avail memory = 61087744 (59656K bytes)
Preloaded elf kernel "kernel" at 0xc040d000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc040d09c.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <ATI Mobility-1 graphics accelerator> at 0.0 irq 11
pcic-pci0: <TI PCI-1225 PCI-CardBus Bridge> at device 4.0 on pci0
pcic-pci0: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][FUNC pci int + CSC serial isa irq]
pcic-pci1: <TI PCI-1225 PCI-CardBus Bridge> at device 4.1 on pci0
pcic-pci1: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][FUNC pci int + CSC serial isa irq]
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0x1050-0x105f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x1060-0x107f irq 5 at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub0: port 1 power on failed, IOERROR
uhub0: port 2 power on failed, IOERROR
chip1: <Intel 82371AB Power management controller> port 0x1040-0x104f at device 7.3 on pci0
chip2: <ESS Technology Maestro 2E Audio controller> port 0x1400-0x14ff irq 5 at device 8.0 on pci0
pci0: <unknown card> (vendor=0x11c1, dev=0x0449) at 16.0 irq 5
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
pcic0: <VLSI 82C146> at port 0x3e0 iomem 0xd0000 irq 9 drq 0 on isa0
pcic0: management irq 9
pccard0: <PC Card bus -- kludge version> on pcic0
pccard1: <PC Card bus -- kludge version> on pcic0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
pccard: card inserted, slot 0
ata1-slave: ata_command: timeout waiting for intr
ata1-slave: identify failed
ad0: 11513MB <TOSHIBA MK1214GAP> [23392/16/63] at ata0-master using UDMA33
acd0: DVD-ROM <TOSHIBA DVD-ROM SD-C2402> at ata1-master using PIO4
Mounting root from ufs:/dev/ad0s1a
logo_saver: no suitable graphics mode
module_register_init: MOD_LOAD (logo_saver, c0d6fa60, 0) error 19
ep0: <3Com Etherlink III 3C589> at port 0x240-0x24f irq 10 slot 0 on pccard0
ep0: Ethernet address 0a:0b:0c:0d:0e:0f
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hardware" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4.3.2.7.2.20000801231512.046c0650>