Date: Wed, 23 Dec 1998 18:25:51 -0800 (PST) From: "Kevin G. Eliuk" <kevin_eliuk@sunshine.net> To: FreeBSD Current <freebsd-current@FreeBSD.ORG> Subject: Once more - ACER ALI and second device Message-ID: <Pine.BSF.4.02A.9812231745010.605-100000@vanessa.eliuk.org>
next in thread | raw e-mail | index | archive | help
On a build as of Dec 21 and after trying a number of different kernels
and swapping positions I was only able to get the cdrom(4X ATAPI) to be
recognized as a slave to the 8.4GB maxtor.
____
Copyright (c) 1992-1998 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 3.0-CURRENT #0: Wed Dec 23 02:19:48 PST 1998
root@vanessa.eliuk.org:/usr/src/sys/compile/CATHERNA
Timecounter "i8254" frequency 1193286 Hz
Timecounter "TSC" frequency 99878456 Hz
CPU: Pentium/P54C (99.88-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x526 Stepping=6
Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
real memory = 33554432 (32768K bytes)
avail memory = 30121984 (29416K bytes)
Bad DMI table checksum!
Probing for devices on PCI bus 0:
chip0: <Host to PCI bridge (vendor=10b9 device=1531)> rev 0xb3 on pci0.0.0
chip1: <AcerLabs M1533 portable PCI-ISA bridge> rev 0xb4 on pci0.2.0
vga0: <S3 ViRGE graphics accelerator> rev 0x06 int a irq 0 on pci0.6.0
ide_pci0: <PCI IDE controller (busmaster capable)> rev 0x20 int a irq 0 on pci0.11.0
ide_pci: controller is simplex, no DMA on secondary channel
Probing for PnP devices:
CSN 1 Vendor ID: YMH0800 [0x0008a865] Serial 0xffffffff Comp ID: PNPb02f [0x2fb0d041]
Probing for devices on the ISA bus:
VESA: v1.2, 4096k memory, flags:0x0, mode table:0xf00c4ab5 (c0004ab5)
VESA: S3 Incorporated. 86C325
sc0 at 0x60-0x6f irq 1 on motherboard
sc0: VGA color <16 virtual consoles, flags=0x0>
sio0 at 0x3f8-0x3ff irq 4 on isa
sio0: type 16550A
sio3 at 0x2e8-0x2ef irq 3 on isa
sio3: tYpe 16550A
lpt0 at 0x378-0x37f irq 7 on isa
lpt0: Interrupt-driven port
lp0: TCP/IP capable interface
... try to identify the yamaha
pcm0 at 0x530 irq 5 drq 0 flags 0xc113 on isa
mss_attach <mss>0 at 0x530 irq 5 dma 0:3 flags 0xc113
setting up yamaha registers
set yamaha master volume to max
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: FIFO enabled, 8 bytes threshold
fd0: 1.44MB 3.5in
wdc0 at 0x1f0-0x1f7 irq 14 flags 0xa0ff on isa
ide_pci: generic_dmainit 01f0:0: warning, IDE controller timing not set
wdc0: unit 0 (wd0): <Maxtor 90840D6>, DMA, 32-bit, multi-block-16
wd0: 8010MB (16406208 sectors), 16276 cyls, 16 heads, 63 S/T, 512 B/S
wdc1 not found at 0x170
npx0 flags 0x1 on motherboard
npx0: INT 16 interface
Intel Pentium detected, installing workaround for F00F bug
changing root device to wd0s2a
wd0: reverting to PIO mode reading fsbn 0 (status 51<rdy,seekdone,err> error 84<badblk,abort>)
Currently:
Primary Master: Maxtor 90840D6
No Slave
Secondary Master: Maxtor 71084AP
Secondary Slave: Torisan CDR-S1G 4X
MB PCChips M560 <http://www.pcchips.com/m560.html>;
Any suggestions to have my 1GB maxtor IDE to be recognized on the
secondary?
--
Regards,
Kevin G. Eliuk
Discover Rock Solid, Discover FreeBSD | http://www.FreeBSD.Org
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.02A.9812231745010.605-100000>