Date: Mon, 31 Jan 2000 16:02:13 +0100 From: "Karsten W. Rohrbach" <karsten@rohrbach.de> To: Nick Hibma <n_hibma@webweaving.org> Cc: Gorden Fischer <gfish123@pacbell.net>, mobile@FreeBSD.ORG Subject: Re: Vaio 505S + fdc driver Message-ID: <20000131160213.B89178@rohrbach.de> In-Reply-To: <Pine.BSF.4.20.0001231256060.3332-100000@localhost>; from n_hibma@webweaving.org on Sun, Jan 23, 2000 at 12:58:19PM %2B0000 References: <Pine.BSF.4.21.0001222233180.27574-100000@uniqsite.com> <Pine.BSF.4.20.0001231256060.3332-100000@localhost>
next in thread | previous in thread | raw e-mail | index | archive | help
my n505x has a "Y-E Data Flashbuster" USB floppy, it gets attached as ugen0. didnt try the umass driver, since my -current is 20000105 i dont know the status of the umass code... /k Nick Hibma(n_hibma@webweaving.org)@Sun, Jan 23, 2000 at 12:58:19PM +0000: > > It's not a USB device. The 505's with a USB floppy come with the floppy > on a proper USB connector. If you want to prove it to yourself, compile > ugen module (cd /sys/modules/ugen; make load) and run usbd -e. If that > does not make a device show up, then there is no USB device connected to > your system. > > The replicator is a normal floppy drive for all I know. > > Nick > > > Has anyone try to make the fdc driver work for Vaio 505S? The drive is > > attached to a replicator (looks and feels like a USB device for me). > > > > I am unable to mount the floppy disk. The dmesg output verifies the > > problem. Is this problem been asked before? If so, can you tell me how > > to make it work? > > > > Fischer > > > > > > dmesg output: > > > > ======================================================================== > > Copyright (c) 1992-1999 FreeBSD Inc. > > Copyright (c) 1982, 1986, 1989, 1991, 1993 > > The Regents of the University of California. All rights reserved. > > FreeBSD 3.4-RELEASE #0: Sat Jan 22 21:11:24 PST 2000 > > root@sony.uniqsite.com:/usr/src/sys/compile/Sony > > Timecounter "i8254" frequency 1193182 Hz > > CPU: Celeron (331.58-MHz 686-class CPU) > > Origin = "GenuineIntel" Id = 0x66a Stepping = 10 > > Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR> > > real memory = 67108864 (65536K bytes) > > avail memory = 62357504 (60896K bytes) > > Pentium Pro MTRR support enabled > > Probing for devices on PCI bus 0: > > chip0: <Intel 82443BX host to PCI bridge (AGP disabled)> rev 0x03 on pci0.0.0 > > fxp0: <Intel EtherExpress Pro 10/100B Ethernet> rev 0x08 int a irq 9 on pci0.6.0 > > fxp0: Ethernet address 08:00:46:04:57:a0 > > chip1: <Intel 82371AB PCI to ISA bridge> rev 0x02 on pci0.7.0 > > ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.7.1 > > uhci0: <Intel 82371AB/EB USB Host Controller> rev 0x01 int d irq 9 on pci0.7.2 > > chip2: <Intel 82371AB Power management controller> rev 0x02 on pci0.7.3 > > vga0: <NeoMagic model 0005 VGA-compatible display device> rev 0x12 int a irq 9 on pci0.8.0 > > pcic0: <Ricoh RL5C475 PCI-CardBus Bridge> rev 0x00 int a irq 255 on pci0.10.0 > > RL5C4XX PCI Config Reg: [CSC isa irq] > > Probing for PnP devices: > > Probing for devices on the ISA bus: > > sc0 on isa > > sc0: VGA color <16 virtual consoles, flags=0x0> > > pcm0 not found > > atkbdc0 at 0x60-0x6f on motherboard > > atkbd0 irq 1 on isa > > psm0 irq 12 flags 0x800 on isa > > psm0: model Generic PS/2 mouse, device ID 0 > > sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa > > sio0: type 16550A > > sio1: configured irq 3 not in bitmap of probed irqs 0 > > sio1 not found at 0x2f8 > > fdc0: direction bit not set > > fdc0: cmd 3 failed at out byte 1 of 3 > > fdc0 not found at 0x3f0 > > wdc0 at 0x1f0-0x1f7 irq 14 flags 0xa0ffa0ff on isa > > wdc0: unit 0 (wd0): <IBM-DBCA-206480>, DMA, 32-bit, multi-block-16 > > wd0: 6194MB (12685680 sectors), 13424 cyls, 15 heads, 63 S/T, 512 B/S > > wdc1 not found at 0x170 > > pcic0 at 0x3e0-0x3e1 irq 11 on isa > > PC-Card ctlr(0) Ricoh RL5C475/476 [CardBus bridge mode] (5 mem & 2 I/O windows) > > pcic0: slot 0 controller I/O address 0x3e0 > > pcic1: sharing irq 11 with other pcic > > pcic1 not found at 0x3e2 > > pcic1: sharing irq 11 with other pcic > > pcic1 not found at 0x3e4 > > vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa > > npx0 on motherboard > > npx0: INT 16 interface > > apm0 on isa > > apm: found APM BIOS version 1.2 > > usb0: <Intel 82371AB/EB USB Host Controller> > > uhub0 at usb0 > > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > > uhub0: 2 ports with 2 removable, self powered > > Initializing PC-card drivers: fdc sio wdc > > changing root device to wd0s2a > > Card inserted, slot 0 > > > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > with "unsubscribe freebsd-mobile" in the body of the message > > > > -- > n_hibma@webweaving.org > n_hibma@freebsd.org USB project > http://www.etla.net/~n_hibma/ > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-mobile" in the body of the message -- > question = ( to ) ? be : ! be; // Wm. Shakespeare http://www.webmonster.de http://www.apache.de http://www.splatterworld.de (NIC-HDL KR433/KR11-RIPE) To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20000131160213.B89178>