Date: Wed, 22 Feb 2012 13:36:20 +0100 From: zulu <zulu@openvps.biz> To: "freebsd-usb@freebsd.org" <freebsd-usb@freebsd.org> Subject: fantec db 229 U3 Message-ID: <1329914180.4f44e14401943@gpo.cellcontainer.com>
next in thread | raw e-mail | index | archive | help
Hi, I can't use my external HDD attached to my la= ptop. The drive enclosure is a Fantec db 229 U3 case (USB3). My lapt= op has only USB2 ports. I have tested this with both FreeBSD = 9.0 RELEASE and FreeBSD 9 STABLE - same issues. Tested wi= th linux too on the same hardware and it is working fine. The manual= which came with the drive enclosure states Linux, Mac OSX and Windo= ws support. Can someone please point me to the right directio= n? I have included some dumps bellow. Many than= ks, Peter dmesg: usb_alloc_device: set = address 2 failed (USB_ERR_STALLED, ignored) usbd_setup_device= _desc: getting device descriptor at addr 2 failed, USB_ERR_STALL= ED usbd_req_re_enumerate: addr=3D2, set address failed! (USB_ERR_STALL= ED, ignored) usbd_setup_device_desc: getting device descriptor= at addr 2 failed, USB_ERR_STALLED usbd_req_re_enumerate: ad= dr=3D2, set address failed! (USB_ERR_STALLED, ignored) usbd_setu= p_device_desc: getting device descriptor at addr 2 failed, USB_ERR_S= TALLED ugen1.2: at usbus1 (disconnected) uhub_reattach_por= t: could not allocate new device usbconfig output: u= gen0.1: at usbus0, cfg=3D0 md=3DHOST spd=3DFULL (12Mbps) pwr=3DSAVE= ugen1.1: at usbus1, cfg=3D0 md=3DHOST spd=3DFULL (12Mbps) pwr=3DSA= VE ugen2.1: at usbus2, cfg=3D0 md=3DHOST spd=3DHIGH (480Mbps) pwr= =3DSAVE ugen3.1: at usbus3, cfg=3D0 md=3DHOST spd=3DFULL (12Mbps) p= wr=3DSAVE ugen4.1: at usbus4, cfg=3D0 md=3DHOST spd=3DFULL (12Mbps) = pwr=3DSAVE ugen5.1: at usbus5, cfg=3D0 md=3DHOST spd=3DFULL (12Mbps= ) pwr=3DSAVE ugen6.1: at usbus6, cfg=3D0 md=3DHOST spd=3DHIGH (480M= bps) pwr=3DSAVE ugen0.2: at usbus0, cfg=3D0 md=3DHOST spd=3DFULL (1= 2Mbps) pwr=3DON ugen0.3: at usbus0, cfg=3D0 md=3DHOST spd=3DFULL (1= 2Mbps) pwr=3DON ugen4.2: at usbus4, cfg=3D0 md=3DHOST spd=3DFULL (1= 2Mbps) pwr=3DON pciconf: uhci2@pci0:0:29:0:class=3D0= x0c0300 card=3D0x20aa17aa chip=3D0x28308086 rev=3D0x03 hdr=3D0x00= vendor =3D 'Intel Corporation' device =3D '82801H (ICH8 Family)= USB UHCI Controller' class =3D serial bus subclass =3D = USB bar [20] =3D type I/O Port, range 32, base 0x18a0, size 32, ena= bled uhci3@pci0:0:29:1:class=3D0x0c0300 card=3D0x20aa17aa chip=3D0x283= 18086 rev=3D0x03 hdr=3D0x00 vendor =3D 'Intel Corporation' d= evice =3D '82801H (ICH8 Family) USB UHCI Controller' class =3D seria= l bus subclass =3D USB bar [20] =3D type I/O Port, range 32, bas= e 0x18c0, size 32, enabled uhci4@pci0:0:29:2:class=3D0x0c0300 card= =3D0x20aa17aa chip=3D0x28328086 rev=3D0x03 hdr=3D0x00 vendor = =3D 'Intel Corporation' device =3D '82801H (ICH8 Family) USB UHCI Co= ntroller' class =3D serial bus subclass =3D USB bar [20] = =3D type I/O Port, range 32, base 0x18e0, size 32, enabled ehci1@pci0:= 0:29:7:class=3D0x0c0320 card=3D0x20ab17aa chip=3D0x28368086 rev=3D0x= 03 hdr=3D0x00 vendor =3D 'Intel Corporation' device =3D '82801H = (ICH8 Family) USB2 EHCI Controller' class =3D serial bus subcla= ss =3D USB bar [10] =3D type Memory, range 32, base 0xfe227000, size= 1024, enabled cap 01[50] =3D powerspec 2 supports D0 D3 current D= 0 cap 0a[58] =3D EHCI Debug Port at offset 0xa0 in map 0x1= 4
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1329914180.4f44e14401943>