Date: Sat, 24 Nov 2001 07:08:25 +0100 From: Emiel Kollof <coolvibe@hackerheaven.org> To: Andy Sparrow <spadger@best.com> Cc: current@freebsd.org, mobile@freebsd.org Subject: Re: PCCARD/NEWCARD won't configure on 5.0 Message-ID: <20011124070825.D24976@laptop.hackerheaven.org> In-Reply-To: <20011124055209.D0E203E31@CRWdog.demon.co.uk> References: <20011124055209.D0E203E31@CRWdog.demon.co.uk>
next in thread | previous in thread | raw e-mail | index | archive | help
--fUYQa+Pmc3FrFX/N
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
* Andy Sparrow (spadger@best.com) wrote:
> As -STABLE won't configure the sound device in my HP Omnibook 6100, I gave
> 5.0-CURRENT a whirl.
CURRENT and STABLE both have support for the ESS1988
(Allegro-1/Maestro3). It's a mere kldload snd_maestro3 away.
My -current running laptop also has a ESS1988 soundcard, and my sound
works just fine under CURRENT and STABLE. No problems with pcmcia
either. I am _not_ running NEWCARD. Never had, never needed to. I
suggest the same for the Omnibook as well.
Attached is my dmesg, just FYI.
Did you try totally powering off the Omnibook and turning it back on?
Sometimes on some laptops, just rebooting leaves the pcmcia in some
undefined state.
Hope that helped,
Cheers,
Emiel
> With a NEWCARD-based kernel, it won't configure the Cardbus controller (which
> works under -STABLE) but it /will/ configure the sound device (an ESS
> Allegro-1).
>
> With a PCCARD-based kernel, 5.0 won't configure the card controller or the
> sound.
>
> Setting or unsetting PCI_ENABLE_IO_MODES in the config file doesn't seem to
> make any difference to the behaviour.
>
> The verbose output of both kernels is attached. With the latest XFree86 from
> CVS, this laptop is this close -><- to working, but I can't choose between
> PCCARD (I don't /need/ Cardbus) or sound.
>
> To add insult to injury, it allegedly Just Works in Hed Rat.
>
> Verbose boot output attached. Anyone got any ideas?
>
>
> Regards,
>
> AS
>
>
>
Content-Description: dmesg-50-pccard-verbose.txt
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD 5.0-CURRENT #1: Sat Nov 24 21:41:33 PST 2001
> root@tureg.geek4food.org:/home/Current/src/sys/i386/compile/test-gen
> Preloaded elf kernel "/boot/kernel/kernel" at 0xc0449000.
> Calibrating clock(s) ... TSC clock: 1129543867 Hz, i8254 clock: 1193154 Hz
> CLK_USE_I8254_CALIBRATION not specified - using default frequency
> Timecounter "i8254" frequency 1193182 Hz
> CLK_USE_TSC_CALIBRATION not specified - using old calibration method
> Timecounter "TSC" frequency 1129576835 Hz
> CPU: Pentium III/Pentium III Xeon/Celeron (1129.58-MHz 686-class CPU)
> Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
> Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
> real memory = 267780096 (261504K bytes)
> Physical memory chunk(s):
> 0x00001000 - 0x0009efff, 647168 bytes (158 pages)
> 0x00470000 - 0x0ff57fff, 263094272 bytes (64232 pages)
> avail memory = 256245760 (250240K bytes)
> bios32: Found BIOS32 Service Directory header at 0xc00f6670
> bios32: Entry = 0xfd7f2 (c00fd7f2) Rev = 0 Len = 1
> pcibios: PCI BIOS entry at 0xfd7f0+0x178
> pnpbios: Found PnP BIOS data at 0xc00f6690
> pnpbios: Entry = f0000:a2e4 Rev = 1.0
> pnpbios: Event flag at 4b4
> Other BIOS signatures found:
> null: <null device, zero device>
> random: <entropy source>
> mem: <memory & I/O>
> Pentium Pro MTRR support enabled
> pci_open(1): mode 1 addr port (0x0cf8) is 0x8000f904
> pci_open(1a): mode1res=0x80000000 (0x80000000)
> pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=35758086)
> Using $PIR table, 14 entries at 0xc00fdee0
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> pcib0: <Host to PCI bridge> at pcibus 0 on motherboard
> pci0: physical bus=0
> map[10]: type 3, range 32, base e0000000, size 28, enabled
> found-> vendor=0x8086, dev=0x3575, revid=0x02
> bus=0, slot=0, func=0
> class=06-00-00, hdrtype=0x00, mfdev=0
> found-> vendor=0x8086, dev=0x3576, revid=0x02
> bus=0, slot=1, func=0
> class=06-04-00, hdrtype=0x01, mfdev=0
> map[20]: type 4, range 32, base 00001800, size 5, enabled
> found-> vendor=0x8086, dev=0x2482, revid=0x01
> bus=0, slot=29, func=0
> class=0c-03-00, hdrtype=0x00, mfdev=0
> intpin=a, irq=10
> found-> vendor=0x8086, dev=0x2448, revid=0x41
> bus=0, slot=30, func=0
> class=06-04-00, hdrtype=0x01, mfdev=0
> found-> vendor=0x8086, dev=0x248c, revid=0x01
> bus=0, slot=31, func=0
> class=06-01-00, hdrtype=0x00, mfdev=1
> map[10]: type 4, range 32, base 000001f0, size 3, enabled
> map[14]: type 4, range 32, base 000003f4, size 2, enabled
> map[18]: type 4, range 32, base 00000170, size 3, enabled
> map[1c]: type 4, range 32, base 00000374, size 2, enabled
> map[20]: type 4, range 32, base 00001820, size 4, enabled
> map[24]: type 1, range 32, base d0000000, size 10, memory disabled
> found-> vendor=0x8086, dev=0x248a, revid=0x01
> bus=0, slot=31, func=1
> class=01-01-8a, hdrtype=0x00, mfdev=0
> intpin=a, irq=255
> map[20]: type 4, range 32, base 00001840, size 5, enabled
> found-> vendor=0x8086, dev=0x2483, revid=0x01
> bus=0, slot=31, func=3
> class=0c-05-00, hdrtype=0x00, mfdev=0
> intpin=b, irq=10
> pci0: <PCI bus> on pcib0
> pcib1: <PCI-PCI bridge> at device 1.0 on pci0
> pcib1: secondary bus 1
> pcib1: subordinate bus 1
> pcib1: I/O decode 0x2000-0x2fff
> pcib1: memory decode 0xd0100000-0xd01fffff
> pcib1: prefetched decode 0xd8000000-0xdfffffff
> pci1: physical bus=1
> map[10]: type 3, range 32, base d8000000, size 27, enabled
> map[14]: type 4, range 32, base 00002000, size 8, enabled
> map[18]: type 1, range 32, base d0100000, size 16, enabled
> found-> vendor=0x1002, dev=0x4c59, revid=0x00
> bus=1, slot=0, func=0
> class=03-00-00, hdrtype=0x00, mfdev=0
> intpin=a, irq=10
> powerspec 2 supports D0 D1 D2 D3 current D0
> pci1: <PCI bus> on pcib1
> pci1: <display, VGA> at device 0.0 (no driver attached)
> uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1800-0x181f irq 10 at device 29.0 on pci0
> usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
> usb0: USB revision 1.0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> pcib2: <PCI-PCI bridge> at device 30.0 on pci0
> pcib2: secondary bus 2
> pcib2: subordinate bus 2
> pcib2: I/O decode 0x3000-0x3fff
> pcib2: memory decode 0xd0200000-0xd02fffff
> pcib2: prefetched decode 0xf0000000-0xf00fffff
> pci2: physical bus=2
> map[10]: type 3, range 32, base f0018000, size 6, enabled
> map[14]: type 3, range 32, base f0000000, size 16, enabled
> map[18]: type 3, range 32, base f0010000, size 15, enabled
> map[1c]: type 4, range 32, base 00003400, size 6, enabled
> found-> vendor=0x10b7, dev=0x1007, revid=0x00
> bus=2, slot=2, func=0
> class=07-80-00, hdrtype=0x00, mfdev=0
> intpin=a, irq=10
> powerspec 2 supports D0 D2 D3 current D0
> map[10]: type 4, range 32, base 00003000, size 8, port disabled
> found-> vendor=0x125d, dev=0x1988, revid=0x12
> bus=2, slot=3, func=0
> class=04-01-00, hdrtype=0x00, mfdev=0
> intpin=a, irq=5
> powerspec 2 supports D0 D1 D2 D3 current D0
> found-> vendor=0x104c, dev=0xac51, revid=0x00
> bus=2, slot=5, func=0
> class=06-07-00, hdrtype=0x02, mfdev=1
> intpin=a, irq=255
> powerspec 2 supports D0 D1 D2 D3 current D0
> found-> vendor=0x104c, dev=0xac51, revid=0x00
> bus=2, slot=5, func=1
> class=06-07-00, hdrtype=0x02, mfdev=1
> intpin=b, irq=255
> powerspec 2 supports D0 D1 D2 D3 current D0
> map[10]: type 1, range 32, base d0200000, size 12, enabled
> map[14]: type 4, range 32, base 00003440, size 6, enabled
> found-> vendor=0x8086, dev=0x1038, revid=0x41
> bus=2, slot=8, func=0
> class=02-00-00, hdrtype=0x00, mfdev=0
> intpin=a, irq=10
> powerspec 2 supports D0 D1 D2 D3 current D0
> pci2: <PCI bus> on pcib2
> pci2: <simple comms> at device 2.0 (no driver attached)
> pci2: <multimedia, audio> at device 3.0 (no driver attached)
> pci_cfgintr_search: linked (62) to configured irq 0 at 0:31:0
> pci_cfgintr: 0:30 INTC routed to irq 0
> pcib2: routed slot 5 INTA to irq 0
> pcic0: <TI PCI-1420 PCI-CardBus Bridge> irq 0 at device 5.0 on pci2
> pcib2: device pcic0 requested unsupported memory range 0x44000000-0xffffffff (decoding 0xd0200000-0xd02fffff, 0xf0000000-0xf00fffff)
> pcic0: Could not grab register memory
> device_probe_and_attach: pcic0 attach returned 12
> pci_cfgintr_linked: linked (63) to hard-routed irq 10
> pci_cfgintr: 0:30 INTD routed to irq 10
> pcib2: routed slot 5 INTB to irq 10
> pcic0: <TI PCI-1420 PCI-CardBus Bridge> irq 10 at device 5.1 on pci2
> pcib2: device pcic0 requested unsupported memory range 0x44000000-0xffffffff (decoding 0xd0200000-0xd02fffff, 0xf0000000-0xf00fffff)
> pcic0: Could not grab register memory
> device_probe_and_attach: pcic0 attach returned 12
> fxp0: <Intel Pro/100 Ethernet> port 0x3440-0x347f mem 0xd0200000-0xd0200fff irq 10 at device 8.0 on pci2
> pcib2: device fxp0 requested decoded memory range 0xd0200000-0xd0200fff
> fxp0: using memory space register mapping
> fxp0: Ethernet address 00:c0:9f:04:82:0c
> fxp0: PCI IDs: 8086 1038 103c 001a 0041
> fxp0: Dynamic Standby mode is disabled
> inphy0: <i82562EM 10/100 media interface> on miibus0
> inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> bpf: fxp0 attached
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH3 ATA100 controller> port 0x1820-0x182f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 mem 0xd0000000-0xd00003ff at device 31.1 on pci0
> ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1820
> ata0: mask=03 ostat0=50 ostat2=00
> ata0-master: ATAPI probe 00 00
> ata0-slave: ATAPI probe 00 00
> ata0: mask=03 stat0=50 stat1=00
> ata0-master: ATA probe 01 a5
> ata0: devices=01
> ata0: at 0x1f0 irq 14 on atapci0
> ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1828
> ata1: mask=03 ostat0=50 ostat2=00
> ata1-master: ATAPI probe 14 eb
> ata1-slave: ATAPI probe 00 00
> ata1: mask=03 stat0=00 stat1=00
> ata1: devices=04
> ata1: at 0x170 irq 15 on atapci0
> pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
> ata-: ata0 already exists, skipping it
> ata-: ata1 already exists, skipping it
> Trying Read_Port at 203
> Trying Read_Port at 243
> Trying Read_Port at 283
> Trying Read_Port at 2c3
> Trying Read_Port at 303
> Trying Read_Port at 343
> Trying Read_Port at 383
> Trying Read_Port at 3c3
> pnpbios: 17 devices, largest 234 bytes
> PNP0c02: adding io range 0x10-0x1f, size=0x10, align=0x1
> PNP0c02: adding io range 0x24-0x25, size=0x2, align=0x1
> PNP0c02: adding io range 0x28-0x29, size=0x2, align=0x1
> PNP0c02: adding io range 0x2c-0x2d, size=0x2, align=0x1
> PNP0c02: adding io range 0x30-0x31, size=0x2, align=0x1
> PNP0c02: adding io range 0x34-0x35, size=0x2, align=0x1
> PNP0c02: adding io range 0x38-0x39, size=0x2, align=0x1
> PNP0c02: adding io range 0x3c-0x3d, size=0x2, align=0x1
> PNP0c02: adding io range 0x50-0x53, size=0x4, align=0x1
> PNP0c02: adding io range 0x72-0x73, size=0x2, align=0x1
> PNP0c02: adding io range 0x74-0x75, size=0x2, align=0x1
> PNP0c02: adding io range 0x76-0x77, size=0x2, align=0x1
> PNP0c02: adding io range 0x80-0x80, size=0x1, align=0x1
> PNP0c02: adding io range 0x90-0x91, size=0x2, align=0x1
> PNP0c02: adding io range 0x92-0x92, size=0x1, align=0x1
> PNP0c02: adding io range 0x93-0x9f, size=0xd, align=0x1
> PNP0c02: adding io range 0xa4-0xa5, size=0x2, align=0x1
> PNP0c02: adding io range 0xa8-0xa9, size=0x2, align=0x1
> PNP0c02: adding io range 0xac-0xad, size=0x2, align=0x1
> PNP0c02: adding io range 0xb0-0xb1, size=0x2, align=0x1
> PNP0c02: adding io range 0xb2-0xb3, size=0x2, align=0x1
> PNP0c02: adding io range 0xb4-0xb5, size=0x2, align=0x1
> PNP0c02: adding io range 0xb8-0xb9, size=0x2, align=0x1
> PNP0c02: adding io range 0xbc-0xbd, size=0x2, align=0x1
> PNP0c02: adding fixed memory32 range 0xfebffc00-0xfebfffff, size=0x400
> PNP0c02: adding fixed memory32 range 0xfff00000-0xffffffff, size=0x100000
> pnpbios: handle 1 device ID PNP0c02 (020cd041)
> PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
> PNP0c01: adding fixed memory32 range 0xe0000-0xfffff, size=0x20000
> PNP0c01: adding fixed memory32 range 0x100000-0x1007fbff, size=0xff7fc00
> pnpbios: handle 2 device ID PNP0c01 (010cd041)
> PNP0200: adding io range 0-0xf, size=0x10, align=0x1
> PNP0200: adding io range 0x81-0x8f, size=0xf, align=0x1
> PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0x1
> PNP0200: adding dma mask 0x10
> pnpbios: handle 3 device ID PNP0200 (0002d041)
> PNP0000: adding io range 0x20-0x21, size=0x2, align=0x1
> PNP0000: adding io range 0xa0-0xa1, size=0x2, align=0x1
> PNP0000: adding irq mask 0x4
> pnpbios: handle 4 device ID PNP0000 (0000d041)
> PNP0100: adding io range 0x40-0x43, size=0x4, align=0x1
> PNP0100: adding irq mask 0x1
> pnpbios: handle 5 device ID PNP0100 (0001d041)
> PNP0b00: adding io range 0x70-0x71, size=0x2, align=0x1
> PNP0b00: adding irq mask 0x100
> pnpbios: handle 6 device ID PNP0b00 (000bd041)
> PNP0303: adding io range 0x60-0x60, size=0x1, align=0x1
> PNP0303: adding io range 0x64-0x64, size=0x1, align=0x1
> PNP0303: adding irq mask 0x2
> pnpbios: handle 7 device ID PNP0303 (0303d041)
> PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0x1
> PNP0c04: adding irq mask 0x2000
> pnpbios: handle 8 device ID PNP0c04 (040cd041)
> PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
> pnpbios: handle 9 device ID PNP0800 (0008d041)
> PNP0c02: adding fixed memory32 range 0xce000-0xcffff, size=0x2000
> pnpbios: handle 10 device ID PNP0c02 (020cd041)
> PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0x1
> pnpbios: handle 11 device ID PNP0a03 (030ad041)
> PNP0c02: adding io range 0x4d0-0x4d1, size=0x2, align=0x1
> PNP0c02: adding io range 0x1000-0x105f, size=0x60, align=0x1
> PNP0c02: adding io range 0x1060-0x107f, size=0x20, align=0x1
> PNP0c02: adding io range 0x1180-0x11bf, size=0x40, align=0x1
> pnpbios: handle 12 device ID PNP0c02 (020cd041)
> INT0800: adding fixed memory32 range 0xffb80000-0xffbfffff, size=0x80000
> INT0800: adding fixed memory32 range 0xffb00000-0xffb7ffff, size=0x80000
> INT0800: adding fixed memory32 range 0xffa80000-0xffafffff, size=0x80000
> INT0800: adding fixed memory32 range 0xffa00000-0xffa7ffff, size=0x80000
> INT0800: adding fixed memory32 range 0xff980000-0xff9fffff, size=0x80000
> INT0800: adding fixed memory32 range 0xff900000-0xff97ffff, size=0x80000
> INT0800: adding fixed memory32 range 0xff880000-0xff8fffff, size=0x80000
> INT0800: adding fixed memory32 range 0xff800000-0xff87ffff, size=0x80000
> INT0800: adding fixed memory32 range 0xff000000-0xff07ffff, size=0x80000
> pnpbios: handle 13 device ID INT0800 (0008d425)
> PNP0401: adding io range 0x378-0x37f, size=0x8, align=0x8
> PNP0401: adding io range 0x778-0x77a, size=0x3, align=0x8
> PNP0401: adding irq mask 0x80
> PNP0401: adding dma mask 0x2
> pnpbios: handle 16 device ID PNP0401 (0104d041)
> PNP0700: adding io range 0x3f0-0x3f5, size=0x6, align=0x8
> PNP0700: adding io range 0x3f7-0x3f7, size=0x1, align=0x1
> PNP0700: adding irq mask 0x40
> PNP0700: adding dma mask 0x4
> pnpbios: handle 18 device ID PNP0700 (0007d041)
> PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0x8
> PNP0501: adding irq mask 0x10
> pnpbios: handle 19 device ID PNP0501 (0105d041)
> PNP0f13: adding irq mask 0x1000
> pnpbios: handle 23 device ID PNP0f13 (130fd041)
> ex_isa_identify()
> sc-: sc0 already exists, skipping it
> vga-: vga0 already exists, skipping it
> isa_probe_children: disabling PnP devices
> isa_probe_children: probing non-PnP devices
> orm0: <Option ROM> at iomem 0xc0000-0xcdfff on isa0
> adv0 failed to probe on isa0
> aha0 failed to probe on isa0
> aic0 failed to probe on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> atkbd: the current kbd controller command byte 0047
> atkbd: keyboard ID 0x41ab (2)
> kbd0 at atkbd0
> kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
> psm0: current command byte:0047
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
> psm0: config:00000000, flags:00000000, packet size:3
> psm0: syncmask:c0, syncbits:00
> bt0 failed to probe on isa0
> cs0 failed to probe at port 0x300-0x31f on isa0
> ed0 failed to probe at port 0x280-0x29f iomem 0xd8000 irq 10 on isa0
> fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
> fdc0: FIFO enabled, 8 bytes threshold
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> fe0 failed to probe at port 0x300-0x31f on isa0
> ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
> le0 failed to probe at port 0x300 iomem 0xd0000 irq 5 on isa0
> lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0
> pcic0: <Intel i82365SL-DF> at port 0x3e0 iomem 0xd0000 on isa0
> pcic0: Polling mode
> pccard0: <PC Card bus (classic)> on pcic0
> pccard1: <PC Card bus (classic)> on pcic0
> pcic1: not probed (disabled)
> pmtimer0 on isa0
> ppc0: parallel port found at 0x378
> ppc0: using extended I/O port range
> ppc0: ECP SPP SPP
> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 1/0/0 bytes threshold
> plip0: <PLIP network interface> on ppbus0
> bpf: lp0 attached
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
> sio0: irq maps: 0x41 0x51 0x41 0x41
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: irq maps: 0x41 0x41 0x41 0x41
> sio1: probe failed test(s): 0 1 2 4 6 7 9
> sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
> sio2: not probed (disabled)
> sio3: not probed (disabled)
> sn0: Cannot allocate irq
> sn0 failed to probe at port 0x300-0x30f irq 10 on isa0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> fb0: vga0, vga, type:VGA (5), flags:0x7007f
> fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
> fb0: init mode:24, bios mode:3, current mode:24
> fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
> vga0: vga: WARNING: video mode switching is not fully supported on this adapter
> VGA parameters upon power-up
> 50 18 10 00 00 00 03 00 02 67 ce 4f 7f 83 84 92
> 28 92 00 6f 0d 0e 00 00 07 80 d5 88 8f 28 1f d4
> e4 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> VGA parameters in BIOS for mode 24
> 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
> bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
> b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> EGA/VGA parameters to be used for mode 24
> 50 18 10 00 00 00 03 00 02 67 ce 4f 7f 83 84 92
> 28 92 00 6f 0d 0e 00 00 07 80 d5 88 8f 28 1f d4
> e4 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> vt0 failed to probe on isa0
> isa_probe_children: probing PnP devices
> unknown: <PNP0303> can't assign resources
> unknown: <PNP0303> at port 0x60 on isa0
> unknown: <PNP0800> failed to probe at port 0x61 on isa0
> unknown: <INT0800> failed to probe at iomem 0xffb80000-0xffbfffff,0xffb00000-0xffb7ffff,0xffa80000-0xffafffff,0xffa00000-0xffa7ffff,0xff980000-0xff9fffff,0xff900000-0xff97ffff,0xff880000-0xff8fffff,0xff800000-0xff87ffff,0xff000000-0xff07ffff on isa0
> unknown: <PNP0401> can't assign resources
> unknown: <PNP0401> at port 0x378-0x37f on isa0
> unknown: <PNP0700> can't assign resources
> unknown: <PNP0700> at port 0x3f0-0x3f5 on isa0
> unknown: <PNP0501> can't assign resources
> unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
> unknown: <PNP0f13> can't assign resources
> unknown: <PNP0f13> at irq 12 on isa0
> BIOS Geometries:
> 0:03feef3f 0..1022=1023 cylinders, 0..239=240 heads, 1..63=63 sectors
> 0 accounted for
> Device configuration finished.
> bpf: lo0 attached
> ad0: success setting UDMA5 on Intel chip
> Creating DISK ad0
> ad0: <IC25N030ATDA04-0/DA4OA70A> ATA-5 disk at ata0-master
> ad0: 28615MB (58605120 sectors), 58140 C, 16 H, 63 S, 512 B
> ad0: 16 secs/int, 1 depth queue, UDMA100
> ad0: piomode=4 dmamode=2 udmamode=5 cblid=1
> ata1-master: piomode=4 dmamode=2 udmamode=-1 dmaflag=1
> ata1-master: success setting PIO4 on generic chip
> acd0: <TOSHIBA CD/DVD-ROM SD-C2502/1915> DVD-ROM drive at ata1 as master
> acd0: read 4134KB/s (34515KB/s), 128KB buffer, PIO4
> acd0: Reads: CD-R, CD-RW, CD-DA stream, DVD-ROM, DVD-R, packet
> acd0: Writes:
> acd0: Audio: play, 16 volume levels
> acd0: Mechanism: ejectable tray, unlocked
> acd0: Medium: no/blank disc
> Mounting root from ufs:/dev/ad0s2a
> ad0s1: type 0xa0, start 63, end = 45359, size 45297 : OK
> ad0s2: type 0xa5, start 45360, end = 58605119, size 58559760 : OK
> start_init: trying /sbin/init
Content-Description: dmesg-50-newcard-verbose.txt
> Copyright (c) 1992-2001 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD 5.0-CURRENT #1: Sat Nov 24 18:38:34 PST 2001
> root@tureg.geek4food.org:/home/Current/src/sys/i386/compile/test
> Preloaded elf kernel "/boot/kernel/kernel" at 0xc045d000.
> Calibrating clock(s) ... TSC clock: 1129541230 Hz, i8254 clock: 1193151 Hz
> CLK_USE_I8254_CALIBRATION not specified - using default frequency
> Timecounter "i8254" frequency 1193182 Hz
> CLK_USE_TSC_CALIBRATION not specified - using old calibration method
> Timecounter "TSC" frequency 1129576993 Hz
> CPU: Pentium III/Pentium III Xeon/Celeron (1129.58-MHz 686-class CPU)
> Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
> Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
> real memory = 267780096 (261504K bytes)
> Physical memory chunk(s):
> 0x00001000 - 0x0009efff, 647168 bytes (158 pages)
> 0x00484000 - 0x0ff57fff, 263012352 bytes (64212 pages)
> avail memory = 256163840 (250160K bytes)
> bios32: Found BIOS32 Service Directory header at 0xc00f6670
> bios32: Entry = 0xfd7f2 (c00fd7f2) Rev = 0 Len = 1
> pcibios: PCI BIOS entry at 0xfd7f0+0x178
> pnpbios: Found PnP BIOS data at 0xc00f6690
> pnpbios: Entry = f0000:a2e4 Rev = 1.0
> pnpbios: Event flag at 4b4
> Other BIOS signatures found:
> null: <null device, zero device>
> random: <entropy source>
> mem: <memory & I/O>
> Pentium Pro MTRR support enabled
> pci_open(1): mode 1 addr port (0x0cf8) is 0x8000f904
> pci_open(1a): mode1res=0x80000000 (0x80000000)
> pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=35758086)
> Using $PIR table, 14 entries at 0xc00fdee0
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> pcib0: <Host to PCI bridge> at pcibus 0 on motherboard
> pci0: physical bus=0
> map[10]: type 3, range 32, base e0000000, size 28, enabled
> found-> vendor=0x8086, dev=0x3575, revid=0x02
> bus=0, slot=0, func=0
> class=06-00-00, hdrtype=0x00, mfdev=0
> found-> vendor=0x8086, dev=0x3576, revid=0x02
> bus=0, slot=1, func=0
> class=06-04-00, hdrtype=0x01, mfdev=0
> map[20]: type 4, range 32, base 00001800, size 5, enabled
> found-> vendor=0x8086, dev=0x2482, revid=0x01
> bus=0, slot=29, func=0
> class=0c-03-00, hdrtype=0x00, mfdev=0
> intpin=a, irq=10
> found-> vendor=0x8086, dev=0x2448, revid=0x41
> bus=0, slot=30, func=0
> class=06-04-00, hdrtype=0x01, mfdev=0
> found-> vendor=0x8086, dev=0x248c, revid=0x01
> bus=0, slot=31, func=0
> class=06-01-00, hdrtype=0x00, mfdev=1
> map[10]: type 4, range 32, base 000001f0, size 3, enabled
> map[14]: type 4, range 32, base 000003f4, size 2, enabled
> map[18]: type 4, range 32, base 00000170, size 3, enabled
> map[1c]: type 4, range 32, base 00000374, size 2, enabled
> map[20]: type 4, range 32, base 00001820, size 4, enabled
> map[24]: type 1, range 32, base d0000000, size 10, memory disabled
> found-> vendor=0x8086, dev=0x248a, revid=0x01
> bus=0, slot=31, func=1
> class=01-01-8a, hdrtype=0x00, mfdev=0
> intpin=a, irq=255
> map[20]: type 4, range 32, base 00001840, size 5, enabled
> found-> vendor=0x8086, dev=0x2483, revid=0x01
> bus=0, slot=31, func=3
> class=0c-05-00, hdrtype=0x00, mfdev=0
> intpin=b, irq=10
> pci0: <PCI bus> on pcib0
> pcib1: <PCI-PCI bridge> at device 1.0 on pci0
> pcib1: secondary bus 1
> pcib1: subordinate bus 1
> pcib1: I/O decode 0x2000-0x2fff
> pcib1: memory decode 0xd0100000-0xd01fffff
> pcib1: prefetched decode 0xd8000000-0xdfffffff
> pci1: physical bus=1
> map[10]: type 3, range 32, base d8000000, size 27, enabled
> map[14]: type 4, range 32, base 00002000, size 8, enabled
> map[18]: type 1, range 32, base d0100000, size 16, enabled
> found-> vendor=0x1002, dev=0x4c59, revid=0x00
> bus=1, slot=0, func=0
> class=03-00-00, hdrtype=0x00, mfdev=0
> intpin=a, irq=10
> powerspec 2 supports D0 D1 D2 D3 current D0
> pci1: <PCI bus> on pcib1
> pci1: <display, VGA> at device 0.0 (no driver attached)
> uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1800-0x181f irq 10 at device 29.0 on pci0
> usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
> usb0: USB revision 1.0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> pcib2: <PCI-PCI bridge> at device 30.0 on pci0
> pcib2: secondary bus 2
> pcib2: subordinate bus 2
> pcib2: I/O decode 0x3000-0x3fff
> pcib2: memory decode 0xd0200000-0xd02fffff
> pcib2: prefetched decode 0xf0000000-0xf00fffff
> pci2: physical bus=2
> map[10]: type 3, range 32, base f0018000, size 6, enabled
> map[14]: type 3, range 32, base f0000000, size 16, enabled
> map[18]: type 3, range 32, base f0010000, size 15, enabled
> map[1c]: type 4, range 32, base 00003400, size 6, enabled
> found-> vendor=0x10b7, dev=0x1007, revid=0x00
> bus=2, slot=2, func=0
> class=07-80-00, hdrtype=0x00, mfdev=0
> intpin=a, irq=10
> powerspec 2 supports D0 D2 D3 current D0
> map[10]: type 4, range 32, base 00003000, size 8, port disabled
> found-> vendor=0x125d, dev=0x1988, revid=0x12
> bus=2, slot=3, func=0
> class=04-01-00, hdrtype=0x00, mfdev=0
> intpin=a, irq=5
> powerspec 2 supports D0 D1 D2 D3 current D0
> found-> vendor=0x104c, dev=0xac51, revid=0x00
> bus=2, slot=5, func=0
> class=06-07-00, hdrtype=0x02, mfdev=1
> intpin=a, irq=255
> powerspec 2 supports D0 D1 D2 D3 current D0
> found-> vendor=0x104c, dev=0xac51, revid=0x00
> bus=2, slot=5, func=1
> class=06-07-00, hdrtype=0x02, mfdev=1
> intpin=b, irq=255
> powerspec 2 supports D0 D1 D2 D3 current D0
> map[10]: type 1, range 32, base d0200000, size 12, enabled
> map[14]: type 4, range 32, base 00003440, size 6, enabled
> found-> vendor=0x8086, dev=0x1038, revid=0x41
> bus=2, slot=8, func=0
> class=02-00-00, hdrtype=0x00, mfdev=0
> intpin=a, irq=10
> powerspec 2 supports D0 D1 D2 D3 current D0
> pci2: <PCI bus> on pcib2
> pci2: <simple comms> at device 2.0 (no driver attached)
> pci2: <multimedia, audio> at device 3.0 (no driver attached)
> pccbb0: <TI1420 PCI-CardBus Bridge> at device 5.0 on pci2
> pcib2: device pccbb0 requested unsupported memory range 0x10000000-0xffffffff (decoding 0xd0200000-0xd02fffff, 0xf0000000-0xf00fffff)
> pccbb0: Could not grab register memory
> device_probe_and_attach: pccbb0 attach returned 12
> pccbb0: <TI1420 PCI-CardBus Bridge> at device 5.1 on pci2
> pcib2: device pccbb0 requested unsupported memory range 0x10000000-0xffffffff (decoding 0xd0200000-0xd02fffff, 0xf0000000-0xf00fffff)
> pccbb0: Could not grab register memory
> device_probe_and_attach: pccbb0 attach returned 12
> fxp0: <Intel Pro/100 Ethernet> port 0x3440-0x347f mem 0xd0200000-0xd0200fff irq 10 at device 8.0 on pci2
> pcib2: device fxp0 requested decoded memory range 0xd0200000-0xd0200fff
> fxp0: using memory space register mapping
> fxp0: Ethernet address 00:c0:9f:04:82:0c
> fxp0: PCI IDs: 8086 1038 103c 001a 0041
> fxp0: Dynamic Standby mode is disabled
> inphy0: <i82562EM 10/100 media interface> on miibus0
> inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> bpf: fxp0 attached
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH3 ATA100 controller> port 0x1820-0x182f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 mem 0xd0000000-0xd00003ff at device 31.1 on pci0
> ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1820
> ata0: mask=03 ostat0=50 ostat2=00
> ata0-master: ATAPI probe 00 00
> ata0-slave: ATAPI probe 00 00
> ata0: mask=03 stat0=50 stat1=00
> ata0-master: ATA probe 01 a5
> ata0: devices=01
> ata0: at 0x1f0 irq 14 on atapci0
> ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1828
> ata1: mask=03 ostat0=50 ostat2=00
> ata1-master: ATAPI probe 14 eb
> ata1-slave: ATAPI probe 00 00
> ata1: mask=03 stat0=00 stat1=00
> ata1: devices=04
> ata1: at 0x170 irq 15 on atapci0
> pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
> ata-: ata0 already exists, skipping it
> ata-: ata1 already exists, skipping it
> Trying Read_Port at 203
> Trying Read_Port at 243
> Trying Read_Port at 283
> Trying Read_Port at 2c3
> Trying Read_Port at 303
> Trying Read_Port at 343
> Trying Read_Port at 383
> Trying Read_Port at 3c3
> ex_isa_identify()
> pnpbios: 17 devices, largest 234 bytes
> PNP0c02: adding io range 0x10-0x1f, size=0x10, align=0x1
> PNP0c02: adding io range 0x24-0x25, size=0x2, align=0x1
> PNP0c02: adding io range 0x28-0x29, size=0x2, align=0x1
> PNP0c02: adding io range 0x2c-0x2d, size=0x2, align=0x1
> PNP0c02: adding io range 0x30-0x31, size=0x2, align=0x1
> PNP0c02: adding io range 0x34-0x35, size=0x2, align=0x1
> PNP0c02: adding io range 0x38-0x39, size=0x2, align=0x1
> PNP0c02: adding io range 0x3c-0x3d, size=0x2, align=0x1
> PNP0c02: adding io range 0x50-0x53, size=0x4, align=0x1
> PNP0c02: adding io range 0x72-0x73, size=0x2, align=0x1
> PNP0c02: adding io range 0x74-0x75, size=0x2, align=0x1
> PNP0c02: adding io range 0x76-0x77, size=0x2, align=0x1
> PNP0c02: adding io range 0x80-0x80, size=0x1, align=0x1
> PNP0c02: adding io range 0x90-0x91, size=0x2, align=0x1
> PNP0c02: adding io range 0x92-0x92, size=0x1, align=0x1
> PNP0c02: adding io range 0x93-0x9f, size=0xd, align=0x1
> PNP0c02: adding io range 0xa4-0xa5, size=0x2, align=0x1
> PNP0c02: adding io range 0xa8-0xa9, size=0x2, align=0x1
> PNP0c02: adding io range 0xac-0xad, size=0x2, align=0x1
> PNP0c02: adding io range 0xb0-0xb1, size=0x2, align=0x1
> PNP0c02: adding io range 0xb2-0xb3, size=0x2, align=0x1
> PNP0c02: adding io range 0xb4-0xb5, size=0x2, align=0x1
> PNP0c02: adding io range 0xb8-0xb9, size=0x2, align=0x1
> PNP0c02: adding io range 0xbc-0xbd, size=0x2, align=0x1
> PNP0c02: adding fixed memory32 range 0xfebffc00-0xfebfffff, size=0x400
> PNP0c02: adding fixed memory32 range 0xfff00000-0xffffffff, size=0x100000
> pnpbios: handle 1 device ID PNP0c02 (020cd041)
> PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
> PNP0c01: adding fixed memory32 range 0xe0000-0xfffff, size=0x20000
> PNP0c01: adding fixed memory32 range 0x100000-0x1007fbff, size=0xff7fc00
> pnpbios: handle 2 device ID PNP0c01 (010cd041)
> PNP0200: adding io range 0-0xf, size=0x10, align=0x1
> PNP0200: adding io range 0x81-0x8f, size=0xf, align=0x1
> PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0x1
> PNP0200: adding dma mask 0x10
> pnpbios: handle 3 device ID PNP0200 (0002d041)
> PNP0000: adding io range 0x20-0x21, size=0x2, align=0x1
> PNP0000: adding io range 0xa0-0xa1, size=0x2, align=0x1
> PNP0000: adding irq mask 0x4
> pnpbios: handle 4 device ID PNP0000 (0000d041)
> PNP0100: adding io range 0x40-0x43, size=0x4, align=0x1
> PNP0100: adding irq mask 0x1
> pnpbios: handle 5 device ID PNP0100 (0001d041)
> PNP0b00: adding io range 0x70-0x71, size=0x2, align=0x1
> PNP0b00: adding irq mask 0x100
> pnpbios: handle 6 device ID PNP0b00 (000bd041)
> PNP0303: adding io range 0x60-0x60, size=0x1, align=0x1
> PNP0303: adding io range 0x64-0x64, size=0x1, align=0x1
> PNP0303: adding irq mask 0x2
> pnpbios: handle 7 device ID PNP0303 (0303d041)
> PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0x1
> PNP0c04: adding irq mask 0x2000
> pnpbios: handle 8 device ID PNP0c04 (040cd041)
> PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
> pnpbios: handle 9 device ID PNP0800 (0008d041)
> PNP0c02: adding fixed memory32 range 0xce000-0xcffff, size=0x2000
> pnpbios: handle 10 device ID PNP0c02 (020cd041)
> PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0x1
> pnpbios: handle 11 device ID PNP0a03 (030ad041)
> PNP0c02: adding io range 0x4d0-0x4d1, size=0x2, align=0x1
> PNP0c02: adding io range 0x1000-0x105f, size=0x60, align=0x1
> PNP0c02: adding io range 0x1060-0x107f, size=0x20, align=0x1
> PNP0c02: adding io range 0x1180-0x11bf, size=0x40, align=0x1
> pnpbios: handle 12 device ID PNP0c02 (020cd041)
> INT0800: adding fixed memory32 range 0xffb80000-0xffbfffff, size=0x80000
> INT0800: adding fixed memory32 range 0xffb00000-0xffb7ffff, size=0x80000
> INT0800: adding fixed memory32 range 0xffa80000-0xffafffff, size=0x80000
> INT0800: adding fixed memory32 range 0xffa00000-0xffa7ffff, size=0x80000
> INT0800: adding fixed memory32 range 0xff980000-0xff9fffff, size=0x80000
> INT0800: adding fixed memory32 range 0xff900000-0xff97ffff, size=0x80000
> INT0800: adding fixed memory32 range 0xff880000-0xff8fffff, size=0x80000
> INT0800: adding fixed memory32 range 0xff800000-0xff87ffff, size=0x80000
> INT0800: adding fixed memory32 range 0xff000000-0xff07ffff, size=0x80000
> pnpbios: handle 13 device ID INT0800 (0008d425)
> PNP0401: adding io range 0x378-0x37f, size=0x8, align=0x8
> PNP0401: adding io range 0x778-0x77a, size=0x3, align=0x8
> PNP0401: adding irq mask 0x80
> PNP0401: adding dma mask 0x2
> pnpbios: handle 16 device ID PNP0401 (0104d041)
> PNP0700: adding io range 0x3f0-0x3f5, size=0x6, align=0x8
> PNP0700: adding io range 0x3f7-0x3f7, size=0x1, align=0x1
> PNP0700: adding irq mask 0x40
> PNP0700: adding dma mask 0x4
> pnpbios: handle 18 device ID PNP0700 (0007d041)
> PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0x8
> PNP0501: adding irq mask 0x10
> pnpbios: handle 19 device ID PNP0501 (0105d041)
> PNP0f13: adding irq mask 0x1000
> pnpbios: handle 23 device ID PNP0f13 (130fd041)
> sc-: sc0 already exists, skipping it
> vga-: vga0 already exists, skipping it
> isa_probe_children: disabling PnP devices
> isa_probe_children: probing non-PnP devices
> orm0: <Option ROM> at iomem 0xc0000-0xcdfff on isa0
> fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
> fdc0: FIFO enabled, 8 bytes threshold
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> adv0 failed to probe on isa0
> bt0 failed to probe on isa0
> aha0 failed to probe on isa0
> aic0 failed to probe on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> atkbd: the current kbd controller command byte 0047
> atkbd: keyboard ID 0x41ab (2)
> kbd0 at atkbd0
> kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
> psm0: current command byte:0047
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
> psm0: config:00000000, flags:00000000, packet size:3
> psm0: syncmask:c0, syncbits:00
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> fb0: vga0, vga, type:VGA (5), flags:0x7007f
> fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
> fb0: init mode:24, bios mode:3, current mode:24
> fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
> vga0: vga: WARNING: video mode switching is not fully supported on this adapter
> VGA parameters upon power-up
> 50 18 10 00 00 00 03 00 02 67 ce 4f 7f 83 84 92
> 28 92 00 6f 0d 0e 00 00 07 80 d5 88 8f 28 1f d4
> e4 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> VGA parameters in BIOS for mode 24
> 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
> bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
> b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> EGA/VGA parameters to be used for mode 24
> 50 18 10 00 00 00 03 00 02 67 ce 4f 7f 83 84 92
> 28 92 00 6f 0d 0e 00 00 07 80 d5 88 8f 28 1f d4
> e4 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
> vt0 failed to probe on isa0
> pmtimer0 on isa0
> pcic0 failed to probe at port 0x3e0 iomem 0xd0000 irq 10 on isa0
> sio0: irq maps: 0x41 0x51 0x41 0x41
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: irq maps: 0x41 0x41 0x41 0x41
> sio1: probe failed test(s): 0 1 2 4 6 7 9
> sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
> sio2: not probed (disabled)
> sio3: not probed (disabled)
> ppc0: parallel port found at 0x378
> ppc0: using extended I/O port range
> ppc0: ECP SPP SPP
> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 1/0/0 bytes threshold
> plip0: <PLIP network interface> on ppbus0
> bpf: lp0 attached
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> ed0 failed to probe at port 0x280-0x29f iomem 0xd8000 irq 10 on isa0
> cs0 failed to probe at port 0x300-0x31f on isa0
> sn0: Cannot allocate irq
> sn0 failed to probe at port 0x300-0x30f irq 10 on isa0
> ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
> fe0 failed to probe at port 0x300-0x31f on isa0
> le0 failed to probe at port 0x300 iomem 0xd0000 irq 5 on isa0
> lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0
> isa_probe_children: probing PnP devices
> unknown: <PNP0303> can't assign resources
> unknown: <PNP0303> at port 0x60 on isa0
> unknown: <PNP0800> failed to probe at port 0x61 on isa0
> unknown: <INT0800> failed to probe at iomem 0xffb80000-0xffbfffff,0xffb00000-0xffb7ffff,0xffa80000-0xffafffff,0xffa00000-0xffa7ffff,0xff980000-0xff9fffff,0xff900000-0xff97ffff,0xff880000-0xff8fffff,0xff800000-0xff87ffff,0xff000000-0xff07ffff on isa0
> unknown: <PNP0401> can't assign resources
> unknown: <PNP0401> at port 0x378-0x37f on isa0
> unknown: <PNP0700> can't assign resources
> unknown: <PNP0700> at port 0x3f0-0x3f5 on isa0
> unknown: <PNP0501> can't assign resources
> unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
> unknown: <PNP0f13> can't assign resources
> unknown: <PNP0f13> at irq 12 on isa0
> BIOS Geometries:
> 0:03feef3f 0..1022=1023 cylinders, 0..239=240 heads, 1..63=63 sectors
> 0 accounted for
> Device configuration finished.
> bpf: lo0 attached
> ad0: success setting UDMA5 on Intel chip
> Creating DISK ad0
> ad0: <IC25N030ATDA04-0/DA4OA70A> ATA-5 disk at ata0-master
> ad0: 28615MB (58605120 sectors), 58140 C, 16 H, 63 S, 512 B
> ad0: 16 secs/int, 1 depth queue, UDMA100
> ad0: piomode=4 dmamode=2 udmamode=5 cblid=1
> ata1-master: piomode=4 dmamode=2 udmamode=-1 dmaflag=1
> ata1-master: success setting PIO4 on generic chip
> acd0: <TOSHIBA CD/DVD-ROM SD-C2502/1915> DVD-ROM drive at ata1 as master
> acd0: read 4134KB/s (34515KB/s), 128KB buffer, PIO4
> acd0: Reads: CD-R, CD-RW, CD-DA stream, DVD-ROM, DVD-R, packet
> acd0: Writes:
> acd0: Audio: play, 16 volume levels
> acd0: Mechanism: ejectable tray, unlocked
> acd0: Medium: no/blank disc
> Mounting root from ufs:/dev/ad0s2a
> ad0s1: type 0xa0, start 63, end = 45359, size 45297 : OK
> ad0s2: type 0xa5, start 45360, end = 58605119, size 58559760 : OK
> start_init: trying /sbin/init
--
Anyone can make an omelet with eggs. The trick is to make one with
none.
--fUYQa+Pmc3FrFX/N
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="dmesg.txt"
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #8: Sat Nov 24 03:08:32 CET 2001
root@tiamat.ipv6.hackerheaven.org:/usr/obj/usr/src/sys/TIAMAT
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0593000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc05930a8.
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 696974952 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (696.97-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory = 134152192 (131008K bytes)
avail memory = 124796928 (121872K bytes)
Pentium Pro MTRR support enabled
VESA: v2.0, 8128k memory, flags:0x0, mode table:0xc04a2502 (1000022)
VESA: ATI MACH64
Using $PIR table, 9 entries at 0xc00fdf30
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <PTLTD RSDT > on motherboard
Timecounter "ACPI" frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_acad0: <AC adapter> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_pcib0: <Host-PCI bridge> port 0xcf8-0xcff,0x22 on acpi0
pci0: <PCI bus> on acpi_pcib0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0x1050-0x105f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x1060-0x107f irq 5 at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: Logitech USB Mouse, rev 1.10/4.00, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
pcic0: <TI PCI-1410 PCI-CardBus Bridge> irq 9 at device 8.0 on pci0
pcic0: PCI Memory allocated: 0x44000000
pcic0: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][CSC serial isa irq]
pccard0: <PC Card bus (classic)> on pcic0
dc0: <Conexant LANfinity MiniPCI 10/100BaseTX> port 0x1400-0x14ff mem 0xf4000000-0xf4003fff irq 9 at device 9.0 on pci0
dc0: Ethernet address: 00:50:8b:fa:2e:0b
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <simple comms> at device 9.1 (no driver attached)
pci0: <multimedia, audio> at device 10.0 (no driver attached)
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
ppc0 port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
fdc0: <NEC 72065B or clone> port 0x3f7,0x3f0-0x3f5 irq 6 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata-: ata0 already exists, skipping it
ata-: ata1 already exists, skipping it
atkbdc-: atkbdc0 already exists, skipping it
fdc-: fdc0 already exists, skipping it
pcic-: pcic0 already exists, skipping it
ppc-: ppc0 already exists, skipping it
sio-: sio0 already exists, skipping it
sc-: sc0 already exists, skipping it
vga-: vga0 already exists, skipping it
orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
acpi_cpu: CPU throttling enabled, 8 steps from 100% to 12.5%
ad0: 9590MB <TOSHIBA MK1016GAP> [19485/16/63] at ata0-master UDMA33
acd0: DVD-ROM <TOSHIBA DVD-ROM SD-C2502> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s1a
pcm0: <ESS Technology Allegro-1> port 0x1800-0x18ff irq 5 at device 10.0 on pci0
--fUYQa+Pmc3FrFX/N--
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20011124070825.D24976>