Date: Tue, 28 May 2013 14:29:53 +0900 From: YongHyeon PYUN <pyunyh@gmail.com> To: Daniel Braniss <danny@cs.huji.ac.il> Cc: freebsd-stable@freebsd.org Subject: Re: SunFire X2200 ilo's bge1 DOWN/UP Message-ID: <20130528052953.GA1457@michelle.cdnetworks.com> In-Reply-To: <E1UgsL2-000DBa-El@kabab.cs.huji.ac.il> References: <E1UgsL2-000DBa-El@kabab.cs.huji.ac.il>
next in thread | previous in thread | raw e-mail | index | archive | help
On Mon, May 27, 2013 at 10:59:28AM +0300, Daniel Braniss wrote: > > On Fri, May 24, 2013 at 05:31:13PM +0300, Daniel Braniss wrote: > > > hi, after upgrading to 9.1-stable, this particular hardware - SunFire X2200, > > > > Show me dmesg(bge(4) and brgphy(4) only) and 'ifconfig bge1' output. > > > > bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x009003> mem > 0xfdff0000-0xfdffffff,0xfdfe0000-0xfdfeffff irq 17 at device 4.0 on pci6 > bge0: CHIP ID 0x00009003; ASIC REV 0x09; CHIP REV 0x90; PCI-X 133 MHz > miibus2: <MII bus> on bge0 > brgphy0: <BCM5714 1000BASE-T media interface> PHY 1 on miibus2 > brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, > 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow > bge0: Ethernet address: 00:1b:24:5d:5b:bd > bge1: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x009003> mem > 0xfdfc0000-0xfdfcffff,0xfdfb0000-0xfdfbffff irq 18 at device 4.1 on pci6 > bge1: CHIP ID 0x00009003; ASIC REV 0x09; CHIP REV 0x90; PCI-X 133 MHz > miibus3: <MII bus> on bge1 > brgphy1: <BCM5714 1000BASE-T media interface> PHY 1 on miibus3 > brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, > 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow > bge1: Ethernet address: 00:1b:24:5d:5b:be > > sf-10> ifconfig bge1 > bge1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=8009b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,LINKSTA > TE> > ether 00:1b:24:5d:5b:be > nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> > media: Ethernet autoselect (100baseTX <full-duplex>) > status: active > Because bge1 is not UP, I wonder how you get link UP/DOWN events. Do you have some network script run by cron? > > > is toggeling bge1 DOWN/UP every few hours, this port is being used by the ILO. > > > To check, I upgraded another identical host, and the same problem appears. > > > > What is the last known working revision? > > I have no idea, but I have older versions, and ill start from the oldets > (9.1-prerelease), but > it will take time, since it takes hours till it happens. > ok.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20130528052953.GA1457>