Date: Fri, 22 Dec 2006 17:33:59 -0500 From: Mike Jakubik <mikej@rogers.com> To: John Polstra <jdp@polstra.com> Cc: hardware@freebsd.org Subject: Re: Is Dell SC1435 likely to work with FreeBSD? Message-ID: <458C5D57.2060003@rogers.com> In-Reply-To: <XFMail.20061222142407.jdp@polstra.com> References: <XFMail.20061222142407.jdp@polstra.com>
next in thread | previous in thread | raw e-mail | index | archive | help
John Polstra wrote: > On 22-Dec-2006 Mike Jakubik wrote: > >> John Polstra wrote: >> >>> I just booted the 6.2-RC1 install CD on the system, and it seems to >>> work fine. It recognized the SATA controller, the hard drive, and the >>> network ports, and the outputs from fdisk and disklabel were >>> correct. I didn't see any signs of problems. >>> >>> I've been running -current on the system for a week or two without >>> any problems. >>> >>> >> Excellent, thank you. Just to be clear though, it is detected as a >> HT1000 SATA controller, not a generic one, right? >> > > Right. I've attached the dmesg output for you to look at. > > I asked Soeren Schmidt about this message: > > ad4: DMA limited to UDMA33, device found non-ATA66 cable > > He says it's because the BIOS set up the SATA controller in ATA > compatibility mode. I asked him whether it affects performance, and > he said "not much". He noted that the memory-mapped region does > appear for the SATA controllers, and said that it may be possible to > modify ata-chipset.c slightly to make it use native SATA mode. I > haven't pursued that because (a) I know very little about SATA, and > (b) the hard drive seems to work fine. > > John > Thanks again John, I've CC'd the list for others that may find this information useful. Also, i made a mistake, i referred to Scott L, when i meant Soren S, thanks for the work Soren. > ------------------------------------------------------------------------ > > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 6.2-RC1 #0: Thu Nov 16 05:01:36 UTC 2006 > root@opus.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC > ACPI APIC Table: <DELL PE_SC3 > > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Dual-Core AMD Opteron(tm) Processor 2210 (1800.08-MHz 686-class CPU) > Origin = "AuthenticAMD" Id = 0x40f12 Stepping = 2 > Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,C > MOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> > Features2=0x2001<SSE3,CX16> > AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow+,3DNow> > AMD Features2=0x1f<LAHF,CMP,<b2>,<b3>,CR8> > Cores per package: 2 > real memory = 2146402304 (2046 MB) > avail memory = 2091376640 (1994 MB) > ioapic0: Changing APIC ID to 2 > ioapic1: Changing APIC ID to 3 > ioapic1: WARNING: intbase 32 != expected base 16 > ioapic2: Changing APIC ID to 4 > ioapic2: WARNING: intbase 64 != expected base 48 > MADT: Forcing active-low polarity and level trigger for SCI > ioapic0 <Version 1.1> irqs 0-15 on motherboard > ioapic1 <Version 1.1> irqs 32-47 on motherboard > ioapic2 <Version 1.1> irqs 64-79 on motherboard > kbd1 at kbdmux0 > ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) > acpi0: <DELL PE_SC3> on motherboard > acpi0: Power Button (fixed) > Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 > acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 > cpu0: <ACPI CPU> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 > pci3: <ACPI PCI bus> on pcib1 > pcib2: <ACPI PCI-PCI bridge> at device 13.0 on pci3 > pci4: <ACPI PCI bus> on pcib2 > atapci0: <ServerWorks HT1000 SATA150 controller> port 0xecb0-0xecb7,0xeca0-0xeca > 3,0xecb8-0xecbf,0xeca4-0xeca7,0xece0-0xecef mem 0xefdfe000-0xefdfffff irq 6 at d > evice 14.0 on pci3 > ata2: <ATA channel 0> on atapci0 > ata3: <ATA channel 1> on atapci0 > atapci1: <ServerWorks HT1000 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x > 177,0x376,0x8c0-0x8cf at device 2.1 on pci0 > ata0: <ATA channel 0> on atapci1 > ata1: <ATA channel 1> on atapci1 > isab0: <PCI-ISA bridge> at device 2.2 on pci0 > isa0: <ISA bus> on isab0 > ohci0: <OHCI (generic) USB controller> port 0xd000-0xd0ff mem 0xefbed000-0xefbed > fff irq 11 at device 3.0 on pci0 > ohci0: [GIANT-LOCKED] > usb0: OHCI version 1.0, legacy support > usb0: SMM does not respond, resetting > usb0: <OHCI (generic) USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > ohci1: <OHCI (generic) USB controller> port 0xd400-0xd4ff mem 0xefbee000-0xefbee > fff irq 11 at device 3.1 on pci0 > ohci1: [GIANT-LOCKED] > usb1: OHCI version 1.0, legacy support > usb1: <OHCI (generic) USB controller> on ohci1 > usb1: USB revision 1.0 > uhub1: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 2 ports with 2 removable, self powered > ehci0: <EHCI (generic) USB 2.0 controller> port 0xd800-0xd8ff mem 0xefbef000-0xe > fbeffff irq 11 at device 3.2 on pci0 > ehci0: [GIANT-LOCKED] > usb2: EHCI version 1.0 > usb2: companion controllers, 2 ports each: usb0 usb1 > usb2: <EHCI (generic) USB 2.0 controller> on ehci0 > usb2: USB revision 2.0 > uhub2: (0x1166) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 > uhub2: 4 ports with 4 removable, self powered > uhub3: vendor 0x413c product 0xa001, class 9/0, rev 2.00/0.00, addr 2 > uhub3: multiple transaction translators > uhub3: 2 ports with 2 removable, self powered > pci0: <display, VGA> at device 4.0 (no driver attached) > pcib3: <ACPI PCI-PCI bridge> irq 32 at device 7.0 on pci0 > pci5: <ACPI PCI bus> on pcib3 > pcib4: <ACPI PCI-PCI bridge> irq 33 at device 8.0 on pci0 > pci1: <ACPI PCI bus> on pcib4 > bge0: <Broadcom BCM5750 C1, ASIC rev. 0x4201> mem 0xefef0000-0xefefffff irq 33 a > t device 0.0 on pci1 > miibus0: <MII bus> on bge0 > brgphy0: <BCM5750 10/100/1000baseTX PHY> on miibus0 > brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX > -FDX, auto > bge0: Ethernet address: 00:18:8b:78:b7:b1 > pcib5: <ACPI PCI-PCI bridge> irq 37 at device 9.0 on pci0 > pci2: <ACPI PCI bus> on pcib5 > bge1: <Broadcom BCM5750 C1, ASIC rev. 0x4201> mem 0xefff0000-0xefffffff irq 37 a > t device 0.0 on pci2 > miibus1: <MII bus> on bge1 > brgphy1: <BCM5750 10/100/1000baseTX PHY> on miibus1 > brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX > -FDX, auto > bge1: Ethernet address: 00:18:8b:78:b7:b2 > pcib6: <ACPI PCI-PCI bridge> irq 35 at device 10.0 on pci0 > pci6: <ACPI PCI bus> on pcib6 > pcib7: <ACPI PCI-PCI bridge> irq 36 at device 11.0 on pci0 > pci7: <ACPI PCI bus> on pcib7 > sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 > sio0: type 16550A, console > sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 > sio1: type 16550A > pmtimer0 on isa0 > orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xc9000-0xc9fff,0xec000-0xeffff > on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > ppc0: parallel port not found. > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x100> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > Timecounter "TSC" frequency 1800080089 Hz quality 800 > Timecounters tick every 1.000 msec > md0: Preloaded image </boot/mfsroot> 4423680 bytes at 0xc0af4014 > acd0: CDROM <HL-DT-ST GCR-8240N/1.10> at ata0-master UDMA33 > ad4: DMA limited to UDMA33, device found non-ATA66 cable > ad4: 238418MB <WDC WD2500JS-75NCB3 10.02E04> at ata2-master UDMA33 > Trying to mount root from ufs:/dev/md0 > /stand/sysinstall running as init on serial console >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?458C5D57.2060003>