Date: Mon, 4 May 2009 17:57:51 -0700 From: Mauro Calderara <mcalderara@phys.ethz.ch> To: freebsd-sparc@FreeBSD.org Subject: Re: 7.2-RELEASE working on Sun Fire V480R Message-ID: <51D049E9-2244-410E-AF62-A0D069DA19DB@phys.ethz.ch> In-Reply-To: <1241482033.86830.2.camel@main.lerwick.hopto.org> References: <4b8db2420905040623o6af3a0c2je96954880a1d32d9@mail.gmail.com> <1241482033.86830.2.camel@main.lerwick.hopto.org>
next in thread | previous in thread | raw e-mail | index | archive | help
> nics are Cassini's I think... > > found-> vendor=0x108e, dev=0xabba, revid=0x11 > > Correct Marius ?? Aww, if you could add support for these, that'd be great! They are also built into the B100s of which I have a few... mauro > On Mon, 2009-05-04 at 16:23 +0300, Olev wrote: >> As it is not listed in supported systems I gave it a shot. Installs >> ok. Onboard ethernet not working. The machine I tested it on has 2x >> PCI SCSI cards inside and it finds them too. Verbose dmesg below: >> >> Sun Fire 480R, No Keyboard >> Copyright 2007 Sun Microsystems, Inc. All rights reserved. >> OpenBoot 4.22.34, 4096 MB memory installed, Serial #53044977. >> Ethernet address 0:3:ba:29:66:f1, Host ID: 832966f1. >> >> Rebooting with command: boot >> Boot device: disk File and args: >> >>>> FreeBSD/sparc64 boot block >> Boot path: /pci@9,600000/SUNW,qlc@2/fp@0,0/ >> disk@w21000004cfb551b1,0:a >> Boot loader: /boot/loader >> Consoles: Open Firmware console >> >> Booting with sun4u support. >> >> FreeBSD/sparc64 bootstrap loader, Revision 1.0 >> (root@obrian.cse.buffalo.edu, Fri May 1 14:51:37 UTC 2009) >> bootpath="/pci@9,600000/SUNW,qlc@2/fp@0,0/disk@w21000004cfb551b1,0:a" >> Loading /boot/defaults/loader.conf >> /boot/kernel/kernel data=0x7c0348+0x78d48 >> syms=[0x8+0x823e0+0x8+0x70aa3] >> / >> Hit [Enter] to boot immediately, or any other key for command prompt. >> Booting [/boot/kernel/kernel] in 8 seconds... >> >> Type '?' for a list of commands, 'help' for more detailed help. >> OK boot -v >> jumping to kernel entry at 0xc0078000. >> Copyright (c) 1992-2009 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, >> 1994 >> The Regents of the University of California. All rights >> reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 7.2-RELEASE #0: Sat May 2 08:25:23 UTC 2009 >> root@obrian.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC >> Preloaded elf kernel "/boot/kernel/kernel" at 0xc092e000. >> real memory = 4294967296 (4096 MB) >> avail memory = 4174045184 (3980 MB) >> machine: SUNW,Sun-Fire-480R >> cpu0: Sun Microsystems UltraSparc-III+ Processor (900.00 MHz CPU) >> mask=0x23 maxtl=5 maxwin=7 >> initalizing intr_countp >> cpu1: Sun Microsystems UltraSparc-III+ Processor (900.00 MHz CPU) >> mask=0x23 maxtl=5 maxwin=7 >> INTR: Adding CPU 1 as a target >> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs >> wlan: <802.11 Link Layer> >> firmware: 'isp_1000' version 1: 20142 bytes loaded at 0xc05fd180 >> registered firmware set <isp_1000> >> firmware: 'isp_1040' version 1: 22944 bytes loaded at 0xc060202e >> registered firmware set <isp_1040> >> firmware: 'isp_1040_it' version 1: 32942 bytes loaded at 0xc06079ce >> registered firmware set <isp_1040_it> >> firmware: 'isp_1080' version 1: 31350 bytes loaded at 0xc060fa7c >> registered firmware set <isp_1080> >> firmware: 'isp_1080_it' version 1: 40644 bytes loaded at 0xc06174f2 >> registered firmware set <isp_1080_it> >> firmware: 'isp_12160' version 1: 28050 bytes loaded at 0xc06213b6 >> registered firmware set <isp_12160> >> firmware: 'isp_12160_it' version 1: 40604 bytes loaded at 0xc0628148 >> registered firmware set <isp_12160_it> >> firmware: 'isp_2100' version 1: 76770 bytes loaded at 0xc0631fe4 >> registered firmware set <isp_2100> >> firmware: 'isp_2200' version 1: 77214 bytes loaded at 0xc0644bc6 >> registered firmware set <isp_2200> >> firmware: 'isp_2300' version 1: 105078 bytes loaded at 0xc0657964 >> registered firmware set <isp_2300> >> firmware: 'isp_2322' version 1: 108856 bytes loaded at 0xc06713da >> registered firmware set <isp_2322> >> firmware: 'isp_2400' version 1: 172952 bytes loaded at 0xc068ef94 >> registered firmware set <isp_2400> >> random: <entropy source, Software, Yarrow> >> kbd0 at kbdmux0 >> nfslock: pseudo-device >> mem: <memory> >> null: <null device, zero device> >> openfirm: <Open Firmware control device> >> nexus0: <Open Firmware Nexus device> >> nexus0: <memory-controller> mem 0x40000400000-0x40000400047 type >> memory-controller (no driver attached) >> nexus0: <memory-controller> mem 0x40001400000-0x40001400047 type >> memory-controller (no driver attached) >> pcib0: <Sun Host-PCI bridge> mem >> 0x40004700000-0x40004717fff,0x40004410000-0x4000441004f, >> 0x7ffee000000-0x7ffee0000ff >> irq 563,560,561,564,565 on nexus0 >> pcib0: Schizo, version 4, IGN 0x8, bus B, 33MHz >> pcib0: DVMA map: 0xc0000000 to 0xffffffff >> pcib0: bus range 0 to 0; PCI bus 0 >> pcib0: [FILTER] >> pci0: <OFW PCI bus> on pcib0 >> pci0: domain=0, physical bus=0 >> found-> vendor=0x108e, dev=0x8001, revid=0x00 >> domain=0, bus=0, slot=0, func=0 >> class=06-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0146, statreg=0x0280, cachelnsz=0 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 >> ns) >> found-> vendor=0x1000, dev=0x000f, revid=0x14 >> domain=0, bus=0, slot=3, func=0 >> class=01-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0146, statreg=0x0200, cachelnsz=16 (dwords) >> lattimer=0x88 (4080 ns), mingnt=0x11 (4250 ns), maxlat=0x40 >> (16000 ns) >> intpin=a, irq=255 >> map[10]: type I/O Port, range 32, base 0x300, size 8, port >> disabled >> map[14]: type Memory, range 32, base 0x100000, size 8, >> enabled >> map[18]: type Memory, range 32, base 0x102000, size 12, >> enabled >> found-> vendor=0x1000, dev=0x000f, revid=0x14 >> domain=0, bus=0, slot=3, func=1 >> class=01-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0146, statreg=0x0200, cachelnsz=16 (dwords) >> lattimer=0x88 (4080 ns), mingnt=0x11 (4250 ns), maxlat=0x40 >> (16000 ns) >> intpin=b, irq=255 >> map[10]: type I/O Port, range 32, base 0x400, size 8, port >> disabled >> map[14]: type Memory, range 32, base 0x104000, size 8, >> enabled >> map[18]: type Memory, range 32, base 0x106000, size 12, >> enabled >> found-> vendor=0x1000, dev=0x000f, revid=0x14 >> domain=0, bus=0, slot=4, func=0 >> class=01-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0146, statreg=0x0200, cachelnsz=16 (dwords) >> lattimer=0x88 (4080 ns), mingnt=0x11 (4250 ns), maxlat=0x40 >> (16000 ns) >> intpin=a, irq=255 >> map[10]: type I/O Port, range 32, base 0x500, size 8, port >> disabled >> map[14]: type Memory, range 32, base 0x108000, size 8, >> enabled >> map[18]: type Memory, range 32, base 0x10a000, size 12, >> enabled >> found-> vendor=0x1000, dev=0x000f, revid=0x14 >> domain=0, bus=0, slot=4, func=1 >> class=01-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0146, statreg=0x0200, cachelnsz=16 (dwords) >> lattimer=0x88 (4080 ns), mingnt=0x11 (4250 ns), maxlat=0x40 >> (16000 ns) >> intpin=b, irq=255 >> map[10]: type I/O Port, range 32, base 0x600, size 8, port >> disabled >> map[14]: type Memory, range 32, base 0x10c000, size 8, >> enabled >> map[18]: type Memory, range 32, base 0x10e000, size 12, >> enabled >> found-> vendor=0x1095, dev=0x0646, revid=0x07 >> domain=0, bus=0, slot=6, func=0 >> class=01-01-8f, hdrtype=0x00, mfdev=0 >> cmdreg=0x0000, statreg=0x0290, cachelnsz=0 (dwords) >> lattimer=0x10 (480 ns), mingnt=0x02 (500 ns), maxlat=0x04 >> (1000 ns) >> intpin=a, irq=255 >> powerspec 1 supports D0 D1 D2 D3 current D0 >> map[10]: type I/O Port, range 32, base 0x700, size 3, port >> disabled >> map[14]: type I/O Port, range 32, base 0x718, size 2, enabled >> map[18]: type I/O Port, range 32, base 0x710, size 3, enabled >> map[1c]: type I/O Port, range 32, base 0x708, size 2, enabled >> map[20]: type I/O Port, range 32, base 0x720, size 4, enabled >> sym0: <875> port 0x300-0x3ff mem 0x100000-0x1000ff,0x102000-0x102fff >> at device 3.0 on pci0 >> sym0: Reserved 0x100 bytes for rid 0x14 type 3 at 0x100000 >> sym0: Reserved 0x1000 bytes for rid 0x18 type 3 at 0x102000 >> sym0: chip clock is 40218KHz >> sym0: No NVRAM, ID 7, Fast-20, SE, parity checking >> sym0: open drain IRQ line driver, using on-chip SRAM >> sym0: using LOAD/STORE-based firmware. >> sym0: [MPSAFE] >> sym0: [ITHREAD] >> sym1: <875> port 0x400-0x4ff mem 0x104000-0x1040ff,0x106000-0x106fff >> at device 3.1 on pci0 >> sym1: Reserved 0x100 bytes for rid 0x14 type 3 at 0x104000 >> sym1: Reserved 0x1000 bytes for rid 0x18 type 3 at 0x106000 >> sym1: chip clock is 40218KHz >> sym1: No NVRAM, ID 7, Fast-20, SE, parity checking >> sym1: open drain IRQ line driver, using on-chip SRAM >> sym1: using LOAD/STORE-based firmware. >> sym1: [MPSAFE] >> sym1: [ITHREAD] >> sym2: <875> port 0x500-0x5ff mem 0x108000-0x1080ff,0x10a000-0x10afff >> at device 4.0 on pci0 >> sym2: Reserved 0x100 bytes for rid 0x14 type 3 at 0x108000 >> sym2: Reserved 0x1000 bytes for rid 0x18 type 3 at 0x10a000 >> sym2: chip clock is 40218KHz >> sym2: No NVRAM, ID 7, Fast-20, SE, parity checking >> sym2: open drain IRQ line driver, using on-chip SRAM >> sym2: using LOAD/STORE-based firmware. >> sym2: [MPSAFE] >> sym2: [ITHREAD] >> sym3: <875> port 0x600-0x6ff mem 0x10c000-0x10c0ff,0x10e000-0x10efff >> at device 4.1 on pci0 >> sym3: Reserved 0x100 bytes for rid 0x14 type 3 at 0x10c000 >> sym3: Reserved 0x1000 bytes for rid 0x18 type 3 at 0x10e000 >> sym3: chip clock is 40218KHz >> sym3: No NVRAM, ID 7, Fast-20, SE, parity checking >> sym3: open drain IRQ line driver, using on-chip SRAM >> sym3: using LOAD/STORE-based firmware. >> sym3: [MPSAFE] >> sym3: [ITHREAD] >> atapci0: <SiI CMD 646U2 UDMA33 controller> port >> 0x700-0x707,0x718-0x71b,0x710-0x717,0x708-0x70b,0x720-0x72f at device >> 6.0 on pci0 >> atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x720 >> pcib0: belatedly registered as interrupt controller for vector 0x208 >> atapci0: [MPSAFE] >> atapci0: [ITHREAD] >> atapci0: HW has secondary channel disabled >> ata2: <ATA channel 0> on atapci0 >> atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x700 >> atapci0: Reserved 0x4 bytes for rid 0x14 type 4 at 0x718 >> ata2: reset tp1 mask=03 ostat0=00 ostat1=00 >> ata2: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb >> ata2: stat1=0x00 err=0x04 lsb=0x00 msb=0x00 >> ata2: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER> >> ata2: [MPSAFE] >> ata2: [ITHREAD] >> pcib1: <Sun Host-PCI bridge> mem >> 0x40004600000-0x40004617fff,0x40004410000-0x4000441004f, >> 0x7ffec000000-0x7ffec0000ff >> irq 562,560,561,564,566 on nexus0 >> pcib1: Schizo, version 4, IGN 0x8, bus A, 66MHz >> Timecounter "pcib1" frequency 150000000 Hz quality 100 >> pcib1: DVMA map: 0xc0000000 to 0xffffffff >> pcib1: bus range 0 to 0; PCI bus 0 >> pcib1: [FILTER] >> pcib1: [FILTER] >> pcib1: [FILTER] >> pcib1: [FILTER] >> pci1: <OFW PCI bus> on pcib1 >> pci1: domain=1, physical bus=0 >> found-> vendor=0x108e, dev=0x8001, revid=0x00 >> domain=1, bus=0, slot=0, func=0 >> class=06-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0146, statreg=0x02a0, cachelnsz=0 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 >> ns) >> pcib2: <Sun Host-PCI bridge> mem >> 0x40004f00000-0x40004f17fff,0x40004c10000-0x40004c1004f, >> 0x7ffea000000-0x7ffea0000ff >> irq 627,624,625,628,629 on nexus0 >> pcib2: Schizo, version 4, IGN 0x9, bus B, 33MHz >> pcib2: DVMA map: 0xc0000000 to 0xffffffff >> pcib2: bus range 0 to 0; PCI bus 0 >> pcib2: [FILTER] >> pci2: <OFW PCI bus> on pcib2 >> pci2: domain=2, physical bus=0 >> found-> vendor=0x108e, dev=0x8001, revid=0x00 >> domain=2, bus=0, slot=0, func=0 >> class=06-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0146, statreg=0x0280, cachelnsz=0 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 >> ns) >> found-> vendor=0x108e, dev=0x1100, revid=0x01 >> domain=2, bus=0, slot=1, func=0 >> class=06-80-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0146, statreg=0x0280, cachelnsz=16 (dwords) >> lattimer=0x50 (2400 ns), mingnt=0x0a (2500 ns), maxlat=0x19 >> (6250 ns) >> map[10]: type Memory, range 32, base 0x7d000000, size 24, >> enabled >> map[14]: type Memory, range 32, base 0x7e000000, size 23, >> enabled >> found-> vendor=0x108e, dev=0x1103, revid=0x01 >> domain=2, bus=0, slot=1, func=3 >> class=0c-03-10, hdrtype=0x00, mfdev=1 >> cmdreg=0x0000, statreg=0x0280, cachelnsz=16 (dwords) >> lattimer=0x50 (2400 ns), mingnt=0x0a (2500 ns), maxlat=0x05 >> (1250 ns) >> map[10]: type Memory, range 32, base 0x1000000, size 15, >> memory disabled >> found-> vendor=0x108e, dev=0xabba, revid=0x11 >> domain=2, bus=0, slot=2, func=0 >> class=02-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0144, statreg=0x04a0, cachelnsz=16 (dwords) >> lattimer=0xff (7650 ns), mingnt=0x40 (16000 ns), maxlat=0x40 >> (16000 ns) >> intpin=a, irq=255 >> map[10]: type Memory, range 32, base 0x200000, size 21, >> memory disabled >> ebus0: <PCI-EBus3 bridge> mem >> 0x7d000000-0x7dffffff,0x7e000000-0x7e7fffff at device 1.0 on pci2 >> ebus0: Reserved 0x1000000 bytes for rid 0x10 type 3 at 0x7d000000 >> ebus0: Reserved 0x800000 bytes for rid 0x14 type 3 at 0x7e000000 >> ebus0: <flashprom> addr 0-0x1fffff (no driver attached) >> ebus0: <bbc> addr 0x100000000-0x1000fffff (no driver attached) >> ebus0: <power> addr 0x10030002e-0x10030002f,0x100300600-0x100300607 >> (no driver attached) >> ebus0: <i2c> addr 0x10000002e-0x10000002f,0x10000002d irq 35 (no >> driver attached) >> ebus0: <i2c> addr 0x100000030-0x100000031 irq 35 (no driver attached) >> rtc0: <Real-Time Clock> addr 0x100300070-0x100300071 irq 36 on ebus0 >> rtc0: registered as a time-of-day clock (resolution 1000000us) >> rtc0: invalid timeebus0: <gpio> addr 0x100300600-0x100300607 (no >> driver attached) >> ebus0: <pmc> addr 0x100300700-0x100300701 (no driver attached) >> uart0: <16550 or compatible> addr 0x1003062f8-0x1003062ff irq 46 on >> ebus0 >> uart0: [FILTER] >> uart0: fast interrupt >> uart1: <16550 or compatible> addr 0x1003083f8-0x1003083ff irq 45 on >> ebus0 >> uart1: [FILTER] >> uart1: fast interrupt >> scc0: <Siemens SAB 82532 dual channel SCC> addr >> 0x100400000-0x10040007f irq 34 on ebus0 >> scc0: not resetting hardware >> scc0: [FILTER] >> uart2: <SAB 82532 v3.2, channel A> on scc0 >> uart2: [FILTER] >> uart2: CTS oflow >> uart2: fast interrupt >> uart2: console (9600,n,8,1) >> uart3: <SAB 82532 v3.2, channel B> on scc0 >> uart3: [FILTER] >> uart3: CTS oflow >> uart3: fast interrupt >> scc0: fast interrupt >> ohci0: <Sun PCIO-2 USB controller> mem 0x1000000-0x1007fff at >> device 1.3 on pci2 >> ohci0: Reserved 0x8000 bytes for rid 0x10 type 3 at 0x1000000 >> ohci0: (New OHCI DeviceId=0x1103108e) >> ohci0: [GIANT-LOCKED] >> ohci0: [ITHREAD] >> usb0: OHCI version 1.0, legacy support >> usb0: <Sun PCIO-2 USB controller> on ohci0 >> usb0: USB revision 1.0 >> uhub0: <(0x108e) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> >> on usb0 >> uhub0: 4 ports with 4 removable, self powered >> pci2: <network, ethernet> at device 2.0 (no driver attached) >> pcib3: <Sun Host-PCI bridge> mem >> 0x40004e00000-0x40004e17fff,0x40004c10000-0x40004c1004f, >> 0x7ffe8000000-0x7ffe80000ff >> irq 626,624,625,628,630 on nexus0 >> pcib3: Schizo, version 4, IGN 0x9, bus A, 66MHz >> Timecounter "pcib3" frequency 150000000 Hz quality 100 >> pcib3: DVMA map: 0xc0000000 to 0xffffffff >> pcib3: bus range 0 to 0; PCI bus 0 >> pcib3: [FILTER] >> pcib3: [FILTER] >> pcib3: [FILTER] >> pcib3: [FILTER] >> pci3: <OFW PCI bus> on pcib3 >> pci3: domain=3, physical bus=0 >> found-> vendor=0x108e, dev=0x8001, revid=0x00 >> domain=3, bus=0, slot=0, func=0 >> class=06-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0146, statreg=0x02a0, cachelnsz=0 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 >> ns) >> found-> vendor=0x108e, dev=0xabba, revid=0x11 >> domain=3, bus=0, slot=1, func=0 >> class=02-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0144, statreg=0x04a0, cachelnsz=16 (dwords) >> lattimer=0xff (7650 ns), mingnt=0x40 (16000 ns), maxlat=0x40 >> (16000 ns) >> intpin=a, irq=255 >> map[10]: type Memory, range 32, base 0x200000, size 21, >> memory disabled >> found-> vendor=0x1077, dev=0x2200, revid=0x05 >> domain=3, bus=0, slot=2, func=0 >> class=01-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0000, statreg=0x02b0, cachelnsz=16 (dwords) >> lattimer=0xf8 (7440 ns), mingnt=0x40 (16000 ns), maxlat=0x00 >> (0 ns) >> intpin=a, irq=255 >> powerspec 1 supports D0 D3 current D0 >> map[10]: type I/O Port, range 32, base 0x300, size 8, port >> disabled >> map[14]: type Memory, range 32, base 0x400000, size 12, >> memory disabled >> pci3: <network, ethernet> at device 1.0 (no driver attached) >> Qlogic ISP Driver, FreeBSD Version 5.9, Core Version 3.0 >> isp0: <Qlogic ISP 2200 PCI FC-AL Adapter> port 0x300-0x3ff mem >> 0x400000-0x400fff at device 2.0 on pci3 >> isp0: Reserved 0x1000 bytes for rid 0x14 type 3 at 0x400000 >> isp0: using Memory space register mapping >> isp0: [MPSAFE] >> isp0: [ITHREAD] >> isp0: Board Type 2200, Chip Revision 0x5, loaded F/W Revision 2.2.6 >> isp0: Last F/W revision was 2.1.105 >> isp0: 309 max I/O command limit set >> isp0: invalid NVRAM header >> isp0: invalid NVRAM header >> isp0: Using Node WWN 0x400000007f000009 >> isp0: Using Port WWN 0x400000007f000009 >> syscons0: no video adapter found. >> nexus0: <syscons> type unknown (no driver attached) >> Reducing kern.maxvnodes 134011 -> 100000 >> procfs registered >> Timecounter "tick" frequency 900000000 Hz quality 10 >> Timecounters tick every 1.000 msec >> lo0: bpf attached >> isp0: LIP Received >> isp0: Loop UP >> isp0: Port Database Changed >> ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=80 wire >> isp0: Firmware State <Config Wait->Ready> >> acd0: setting PIO4 on CMD 646U2 chip >> isp0: HBA PortID 0x000029 N-Port Handle 109, Connection Topology >> 'Private Loop' >> isp0: HBA WWNN 0x400000007f000009 HBA WWPN 0x400000007f000009 >> isp0: PortID 0x0000ef handle 0x0 role Target arrived at tgt 0 >> WWNN 0x20000004cfb551b1 WWPN 0x21000004cfb551b1 >> isp0: PortID 0x0000e8 handle 0x1 role Target arrived at tgt 1 >> WWNN 0x20000004cfb558ed WWPN 0x21000004cfb558ed >> acd0: <TOSHIBA DVD-ROM SD-C2512/1013> DVDR drive at ata2 as master >> acd0: read 4134KB/s (4134KB/s) write 172KB/s, 512KB buffer, PIO4 >> acd0: Reads: CDDA >> acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write >> acd0: Audio: play, 16 volume levels >> acd0: Mechanism: ejectable tray, unlocked >> acd0: Medium: no/blank disc >> Waiting 5 seconds for SCSI devices to settle >> (noperiph:sym0:0:-1:-1): SCSI BUS reset delivered. >> (noperiph:sym1:0:-1:-1): SCSI BUS reset delivered. >> (noperiph:sym2:0:-1:-1): SCSI BUS reset delivered. >> (noperiph:sym3:0:-1:-1): SCSI BUS reset delivered. >> (probe0:isp0:0:0:0): Retrying Command >> (probe1:isp0:0:1:0): Retrying Command >> pass0 at isp0 bus 0 target 0 lun 0 >> pass0: <SEAGATE ST336605FSUN36G 0638> Fixed Direct Access SCSI-3 >> device >> pass0: Serial Number 3FP233TR00007316NY71 >> pass0: 100.000MB/s transfers >> pass0: Command Queueing Enabled >> pass1 at isp0 bus 0 target 1 lun 0 >> pass1: <SEAGATE ST336605FSUN36G 0638> Fixed Direct Access SCSI-3 >> device >> pass1: Serial Number 3FP239L000007315HL0H >> pass1: 100.000MB/s transfers WWNN 0x20000004cfb558ed WWPN >> 0x21000004cfb558ed PortID 0xe8 >> pass1: Command Queueing Enabled >> GEOM: new disk da0 >> GEOM: new disk da1 >> da0 at isp0 bus 0 target 0 lun 0 >> da0: <SEAGATE ST336605FSUN36G 0638> Fixed Direct Access SCSI-3 device >> da0: Serial Number 3FP233TR00007316NY71 >> da0: 100.000MB/s transfers >> da0: Command Queueing Enabled >> da0: 34732MB (71132959 512 byte sectors: 255H 63S/T 4427C) >> da1 at isp0 bus 0 target 1 lun 0 >> da1: <SEAGATE ST336605FSUN36G 0638> Fixed Direct Access SCSI-3 device >> da1: Serial Number 3FP239L000007315HL0H >> da1: 100.000MB/s transfers WWNN 0x20000004cfb558ed WWPN >> 0x21000004cfb558ed PortID 0xe8 >> da1: Command Queueing Enabled >> da1: 34732MB (71132959 512 byte sectors: 255H 63S/T 4427C) >> SMP: AP CPU #1 Launched! >> _______________________________________________ >> freebsd-sparc64@freebsd.org mailing list >> http://lists.freebsd.org/mailman/listinfo/freebsd-sparc64 >> To unsubscribe, send any mail to "freebsd-sparc64-unsubscribe@freebsd.org >> " > > _______________________________________________ > freebsd-sparc64@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-sparc64 > To unsubscribe, send any mail to "freebsd-sparc64-unsubscribe@freebsd.org > "
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?51D049E9-2244-410E-AF62-A0D069DA19DB>