Date: Sat, 06 Jul 2002 11:44:07 -0700 From: Randy Bush <randy@psg.com> To: Orion Hodson <hodson@icir.org> Cc: freebsd-multimedia@freebsd.org Subject: Re: ADI 1885 audio support Message-ID: <E17QuXP-00008t-00@rip.psg.com> References: <E17QtUf-000HQ7-00@rip.psg.com> <200207061821.g66ILRC63814@puma.icir.org>
next in thread | previous in thread | raw e-mail | index | archive | help
> % mixer vol 80 pcm 80
> % mpg123 sometune.mp3
same old same old. i do get clicks when booting etc. and i do have the
speakers plugged into the line-out/speaker jack (there is just the single
jack on the intel mobo).
> If that doesn't do it, can you post the output of a verbose boot.
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.6-STABLE #1: Sat Jul 6 11:12:21 PDT 2002
root@rip.psg.com:/usr/obj/usr/src/sys/RIP
Calibrating clock(s) ... TSC clock: 1694820052 Hz, i8254 clock: 1193161 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC" frequency 1694858164 Hz
CPU: Pentium 4 (1694.86-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf12 Stepping = 2
Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,<b28>,ACC>
real memory = 536608768 (524032K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x003b8000 - 0x1ffb7fff, 532676608 bytes (130048 pages)
avail memory = 518492160 (506340K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00fda60
bios32: Entry = 0xfda74 (c00fda74) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xda95
pnpbios: Found PnP BIOS data at 0xc00f27a0
pnpbios: Entry = f0000:209a Rev = 1.0
Other BIOS signatures found:
ACPI: 000ff980
Preloaded elf kernel "kernel" at 0xc0391000.
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000005c
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25308086)
Using $PIR table, 13 entries at 0xc00f2d90
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x2530, revid=0x04
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base f8000000, size 26
found-> vendor=0x8086, dev=0x2532, revid=0x04
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x8086, dev=0x244e, revid=0x04
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=2 secondarybus=2
found-> vendor=0x8086, dev=0x2440, revid=0x04
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x244b, revid=0x04
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000ffa0, size 4
found-> vendor=0x8086, dev=0x2442, revid=0x04
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=5
map[20]: type 1, range 32, base 0000ef80, size 5
found-> vendor=0x8086, dev=0x2443, revid=0x04
class=0c-05-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=b, irq=10
map[20]: type 1, range 32, base 0000efa0, size 4
found-> vendor=0x8086, dev=0x2445, revid=0x04
class=04-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=b, irq=10
map[10]: type 1, range 32, base 0000e800, size 8
map[14]: type 1, range 32, base 0000ef00, size 6
pci0: <PCI bus> on pcib0
pcib1: <PCI to PCI bridge (vendor=8086 device=2532)> at device 1.0 on pci0
found-> vendor=0x102b, dev=0x0525, revid=0x82
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base f2000000, size 25
map[14]: type 1, range 32, base fe9fc000, size 14
map[18]: type 1, range 32, base fe000000, size 23
pci1: <PCI bus> on pcib1
pci1: <Matrox MGA G400 AGP graphics accelerator> (vendor=0x102b, dev=0x0525) at 0.0 irq 11
pcib2: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
found-> vendor=0x1033, dev=0x0035, revid=0x41
class=0c-03-10, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base feafc000, size 12
found-> vendor=0x1033, dev=0x0035, revid=0x41
class=0c-03-10, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=b, irq=7
map[10]: type 1, range 32, base feafd000, size 12
found-> vendor=0x1033, dev=0x00e0, revid=0x02
class=0c-03-20, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=c, irq=9
map[10]: type 1, range 32, base feafec00, size 8
found-> vendor=0x8086, dev=0x2449, revid=0x03
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base feafb000, size 12
map[14]: type 1, range 32, base 0000df00, size 6
found-> vendor=0x9005, dev=0x0081, revid=0x02
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base 0000d800, size 8
map[14]: type 1, range 64, base feaff000, size 12
found-> vendor=0x109e, dev=0x036e, revid=0x02
class=04-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base f57fe000, size 12
found-> vendor=0x109e, dev=0x0878, revid=0x02
class=04-80-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base f57ff000, size 12
pci2: <PCI bus> on pcib2
ohci0: <NEC uPD 9210 USB controller> mem 0xfeafc000-0xfeafcfff irq 5 at device 1.0 on pci2
usb0: OHCI version 1.0
usb0: SMM does not respond, resetting
usb0: <NEC uPD 9210 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ohci1: <NEC uPD 9210 USB controller> mem 0xfeafd000-0xfeafdfff irq 7 at device 1.1 on pci2
usb1: OHCI version 1.0
usb1: SMM does not respond, resetting
usb1: <NEC uPD 9210 USB controller> on ohci1
usb1: USB revision 1.0
uhub1: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
pci2: <USB controller> (vendor=0x1033, dev=0x00e0) at 1.2 irq 9
fxp0: <Intel Pro/100 Ethernet> port 0xdf00-0xdf3f mem 0xfeafb000-0xfeafbfff irq 11 at device 8.0 on pci2
fxp0: using memory space register mapping
fxp0: Ethernet address 00:03:47:fa:d9:e7
fxp0: PCI IDs: 8086 2449 8086 3013 0003
fxp0: Dynamic Standby mode is disabled
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: fxp0 attached
ahc0: <Adaptec 19160B Ultra160 SCSI adapter> port 0xd800-0xd8ff mem 0xfeaff000-0xfeafffff irq 9 at device 11.0 on pci2
ahc0: Reading SEEPROM...done.
ahc0: BIOS eeprom is present
ahc0: Secondary Low byte termination Enabled
ahc0: Primary Low Byte termination Enabled
ahc0: Primary High Byte termination Enabled
ahc0: Downloading Sequencer Program... 419 instructions downloaded
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
bktr0: <BrookTree 878> mem 0xf57fe000-0xf57fefff irq 10 at device 12.0 on pci2
iicbb0: <I2C bit-banging driver> on bti2c0
iicbus0: <Philips I2C bus> on iicbb0 master-only
iicbus: iic devclass not found
iicbus1: <Philips I2C bus> on iicbb0 master-only
iicbus: iic devclass not found
smbus0: <System Management Bus> on bti2c0
smbus: smb devclass not found
brooktree0: PCI bus latency is 32.
bktr0: buffer size 3555328, addr 0x5000000
bktr0: GPIO is 0x00fffffb
bktr0: subsystem 0x0070 0x13eb
bktr0: Hauppauge Model 61111 A M
bktr0: Detected a MSP3430G-A1 at 0x80
bktr0: Hauppauge WinCast/TV, Philips NTSC tuner, msp3400c stereo.
pci2: <unknown card> (vendor=0x109e, dev=0x0878) at 12.1 irq 10
isab0: <Intel 82801BA/BAM (ICH2) PCI to LPC bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH2 ATA100 controller> port 0xffa0-0xffaf at device 31.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xffa0
ata0: mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI 14 eb
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=00 stat1=00
ata0: devices=04
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xffa8
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port 0xef80-0xef9f irq 5 at device 31.2 on pci0
using shared irq5.
usb2: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <unknown card> (vendor=0x8086, dev=0x2443) at 31.3 irq 10
pcm0: <Intel 82801BA (ICH2)> port 0xef00-0xef3f,0xe800-0xe8ff irq 10 at device 31.5 on pci0
using shared irq10.
pcm0: ac97 codec id 0x41445360 (Analog Devices AD1885)
pcm0: ac97 codec features headphone, 6 bit master volume, Analog Devices Phat Stereo
pcm0: ac97 primary codec extended features variable rate PCM
pcm0: sndbuf_setmap b000, 4000; 0xd5e16000 -> b000
pcm0: sndbuf_setmap f000, 4000; 0xd5e1a000 -> f000
ata-: ata0 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROM> at iomem 0xc0000-0xc87ff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata2 failed to probe at port 0x1f0 irq 14 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 06 40 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x441 0x451 0x441 0x441
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x441 0x449 0x441 0x441
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
IP packet filtering initialized, divert disabled, rule-based forwarding disabled, default to deny, unlimited logging
ata0-master: piomode=4 dmamode=2 udmamode=2 dmaflag=1
ata0-master: success setting PIO4 on generic chip
acd0: <SONY CD-RW CRX185E1/XYS2> CD-RW drive at ata0 as master
acd0: read 24750KB/s (32026KB/s) write 172KB/s (5500KB/s), 2048KB buffer, PIO4
acd0: Reads: CD-R, CD-RW, CD-DA stream, packet
acd0: Writes: CD-R, CD-RW, test write, burnproof
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
Waiting 5 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
pcm0: measured ac97 link rate at 55930 Hz
(ahc0:A:0:0): Sending PPR bus_width 1, period 9, offset 7f, ppr_options 2
(ahc0:A:0:0): Received PPR width 1, period 9, offset 3f,options 2
Filtered to width 1, period 9, offset 3f, options 2
ahc0: target 0 using 16bit transfers
ahc0: target 0 synchronous at 80.0MHz DT, offset = 0x3f
Creating DISK da0
pass0 at ahc0 bus 0 target 0 lun 0
pass0: <IBM IC35L036UWPR15-0 S80C> Fixed Direct Access SCSI-3 device
pass0: Serial Number PVY1B326
pass0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da0 at ahc0 bus 0 target 0 lun 0
da0: <IBM IC35L036UWPR15-0 S80C> Fixed Direct Access SCSI-3 device
da0: Serial Number PVY1B326
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da0: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)
Mounting root from ufs:/dev/da0s1a
da0s1: type 0xa5, start 63, end = 71682029, size 71681967 : OK
start_init: trying /sbin/init
Linux ELF exec handler installed
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-multimedia" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?E17QuXP-00008t-00>