Date: Sun, 25 Jan 2004 14:21:54 -0700 From: Tom Ponsford <tponsford@theriver.com> To: freebsd-alpha@freebsd.org, freebsd-current@FreeBSD.ORG Subject: Re: Same problem, new year 2100A machine check Message-ID: <40143372.8090207@theriver.com> In-Reply-To: <4011B6F6.5040306@theriver.com> References: <4011B6F6.5040306@theriver.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi All, Well I'm now 99% sure this it is not a pilot error or a config error. I booted, in MP mode: Windows NT, VMS, Redhat Linux 7.2 (the HP/compaq edition) Tru64 and in uniprocessor mode: FreeBSD 4.6, 4.7-Release/Stable into sysinstall NetBSD (really surprised..but it didn't see the disks) into the install program. It DOES NOT boot: FreeBSD 4.xx MP kernel -machine check as it probes PCI/EISA bus FreeBSD 5.0, 5.2 uniprocessor kernel or MP kernel--machine check as it probes PCI/EISA bus. I'll file a bug report soon. Cheers Tom Ponsford > Hi All, > > I decided to replace a disk on the ol' 2100A. I had been running VMS on > it without any troubles, until a disk started giving me errors. After > replacing the disk, I decided to give 5.2 a go, thinking maybe some of > the problems of last year may have been resolved. > > No such luck. > > As you can see below, it's doing the machine check at almost the same > point as last year. In combing the archives, it seems that there were > problems with some cards, so I yanked out all the pci cards (there were > no EISA cards), still a machine check. > > This machine booted and ran stable under 4-xx with a uniprocessor kernel > > It seems you may have to disable the machine checks in order to get this > beast to boot, any pointers on where to start? > I'd like to play with it with FBSD before going back to VMS. > > Below is the console firmware pre-boot diag and then the actual boot -v > output and then the show config and show fru. > > Cheers > > Tom > > > #################################################### > VMS PALcode V5.56-7, OSF PALcode V1.45-12 > > starting console on CPU 0 > initialized idle PCB > initializing semaphores > initializing heap > initial heap 1c0c0 > memory low limit = 13c000 > heap = 1c0c0, 13fc0 > initializing driver structures > initializing idle process PID > XDELTA not enabled > initializing file system > initializing timer data structures > lowering IPL > CPU 0 speed is 3.64 ns (275MHz) > create dead_eater > create poll > create timer > create powerup > access NVRAM > entering idle loop > Starting Memory Diagnostics > Testing CSIC on Memory Module 0 > Testing CSIC on Memory Module 3 > Testing 1st 8MB(s) on memory module 0 > Testing all memory banks in parallel > Testing Memory bank 0 > Testing Memory bank 1 > Testing Memory bank 2 > Testing Memory bank 3 > Configuring Memory Modules > Configured memory size = 28000000 > Memory Diagnostics completed > probing hose 0, PCI > probing PCI-to-EISA bridge, bus 1 > probing PCI-to-PCI bridge, bus 2 > bus 2, slot 1 -- pka -- NCR 53C810 > starting console on CPU 1 > initialized idle PCB > initializing idle process PID > lowering IPL > CPU 1 speed is 3.64 ns (275MHz) > create powerup > antering idle loopst > rting console on CPU 2 > initialized idle PCB > initializing idle process PID > lowering IPL > starting console on CPU 3 > initialized idle PCB > initializing idle process PID > lowering IPL > CPU 2 speed is 3.64 ns (275MHz) > create powerup > CPU 3 speed is 3.64 ns (275MHz) > create powerup > os_type: UNIX - console CIPCA driver not started > Memory Testing and Configuration Status > Module Size Base Addr Intlv Mode Intlv Unit Status > ------ ----- --------- ---------- ---------- ------ > 0 128MB 20000000 1-Way 0 Passed > 3 512MB 00000000 1-Way 0 Passed > Total Bad Pages 0 > Testing the System > Testing the Disks (read only) > AlphaServer 2100A Console V5.3-10, built on Oct 16 1998 at 14:06:58 > > > ################################################################ > P00>>>boot dka500 > (boot dka500.5.0.2001.0) > block 0 of dka500.5.0.2001.0 is a valid boot block > reading 393 blocks from dka500.5.0.2001.0 > bootstrap code read in > base = 200000, image_start = 0, image_bytes = 31200 > initializing HWRPB at 2000 > initializing page table at 27ff0000 > initializing machine state > setting affinity to the primary CPU > jumping to bootstrap code > Console: SRM firmware console > VMS PAL rev: 0x4000700010538 > OSF PAL rev: 0x4000c0002012d > Switch to OSF PAL code succeeded. > > FreeBSD/alpha SRM CD9660 boot, Revision 1.2 > (root@mithlond.btc.adaptec.com, Sat Jan 10 12:52:28 GMT 2004) > Memory: 655360 k > Loading /boot/defaults/loader.conf > /boot/kernel/kernel data=0x508f30+0x418f0 syms=[0x8+0x671d0+0x8+0x5115f] > | > Hit [Enter] to boot immediately, or any other key for command prompt. > Booting [/boot/kernel/kernel] in 9 seconds... > > Type '?' for a list of commands, 'help' for more detailed help. > OK boot -v > Entering /boot/kernel/kernel at 0xfffffc0000342f20... > Copyright (c) 1992-2004 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 5.2-RELEASE #0: Sun Jan 11 01:06:36 GMT 2004 > root@mithlond.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC > Preloaded elf kernel "/boot/kernel/kernel" at 0xfffffc0000d3e000. > Preloaded mfs_root "/boot/mfsroot" at 0xfffffc0000d3e0e0. > DEC AlphaServer 2100A > AlphaServer 2100A 4/275, 274MHz > 8192 byte page size, 4 processors. > CPU: EV45 (21064A) major=6 minor=2 > OSF PAL rev: 0x4000c0002012d > real memory = 668917760 (637 MB) > Physical memory chunk(s): > 0x00d60000 - 0x2767bfff, 647086080 bytes (78990 pages) > avail memory = 637779968 (608 MB) > smp_start_secondary: starting cpu 1 > smp_start_secondary: cpu 1 started > smp_start_secondary: starting cpu 2 > smp_start_secondary: cpu 2 started > smp_start_secondary: starting cpu 3 > smp_start_secondary: cpu 3 started > FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs > null: <null device, zero device> > random: <entropy source> > mem: <memory & I/O> > t20: using interrupt type 1 on pci bus 0 > t20: <T2 Core Logic chipset> > pcib0: <T2 PCI host bus adapter> on t20 > pci0: <PCI bus> on pcib0 > pci0: physical bus=0 > found-> vendor=0x8086, dev=0x0482, revid=0x15 > bus=0, slot=2, func=0 > class=00-00-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords) > lattimer=0xf8 (7440 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > found-> vendor=0x1011, dev=0x0001, revid=0x02 > bus=0, slot=3, func=0 > class=06-04-00, hdrtype=0x01, mfdev=0 > cmdreg=0x0007, statreg=0x0a80, cachelnsz=8 (dwords) > lattimer=0xf8 (7440 ns), mingnt=0x27 (9750 ns), maxlat=0x00 (0 ns) > eisab0: <PCI-EISA bridge> at device 2.0 on pci0 > > unexpected machine check: > > mces = 0x1 > vector = 0x670 > param = 0xfffffc0000006000 > pc = 0xfffffc00003b48d4 > ra = 0xfffffc00003b4908 > curproc = 0xfffffc0000810ee0 > pid = 0, comm = swapper > > panic: machine check > cpuid = 0; > Uptime: 1s > Automatic reboot in 15 seconds - press a key on the console to abort > > > ###################################################### > P00>>>show fru > > Rev Events logged > Slot Option Part# Hw Sw Serial# SDD TDD > 0 IO 24283-01 C2 0 KA713VPLRL 00 00 > 1 CPU2 B2024-AA D4 9 KA525BATCW 00 00 > 2 CPU0 B2024-AA D4 9 KA510UEZ56 00 00 > 3 CPU1 B2024-AA D4 11 AY63613177 00 00 > 5 CPU3 B2024-AA D4 9 KA537DKVWJ 00 00 > 4 MEM0 B2022-DA B1 0 AY72239742 00 00 > 7 MEM3 B2022-FA B1 0 AY52311544 00 00 > > Slot Option Hose 0, Bus 2, PCI on Primary I/O > > Slot Option Hose 0, Bus 0, PCI on Primary I/O > > Slot Option Hose 0, Bus 1, EISA on Primary I/O > ###################################################### > P00>>>show config > Digital Equipment Corporation > AlphaServer 2100A 4/275 > > SRM Console V5.3-10 VMS PALcode V5.56-7, OSF PALcode V1.45-12 > > Component Status Module ID > CPU 0 P B2024-AA DECchip (tm) 21064A-2 > CPU 1 P B2024-AA DECchip (tm) 21064A-2 > CPU 2 P B2024-AA DECchip (tm) 21064A-2 > CPU 3 P B2024-AA DECchip (tm) 21064A-2 > Memory 0 P B2022-DA 128 MB > Memory 3 P B2022-FA 512 MB > I/O 24283-01 > dva0.0.0.1000.0 RX26/RX23 > > Slot Option Hose 0, Bus 0, PCI > 2 Intel 82375 Bridge to Bus 1, > EISA > 3 DECchip 21050-AA Bridge to Bus 2, > PCI > > Slot Option Hose 0, Bus 1, EISA > > Slot Option Hose 0, Bus 2, PCI > 1 NCR 53C810 pka0.7.0.2001.0 SCSI Bus ID 7 > dka0.0.0.2001.0 RZ28D > dka300.3.0.2001.0 SEAGATE ST15230W > SUN4.2G > dka500.5.0.2001.0 RRD45 > > > > > _______________________________________________ > freebsd-alpha@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-alpha > To unsubscribe, send any mail to "freebsd-alpha-unsubscribe@freebsd.org" >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?40143372.8090207>