Date: Thu, 19 Dec 2002 19:08:15 -0500 (EST) From: Mark Stosberg <mark@summersault.com> To: freebsd-hardware@freebsd.org Subject: trouble with VIA EPIA 5000 system- WRITE command failed Message-ID: <Pine.BSF.4.51.0212191905230.8899@nollie.summersault.com>
next in thread | raw e-mail | index | archive | help
Hello, I recently upgraded my home FreeBSD machine to a system based around the VIA EPIA 5000 motherboard. (Which is a great system that's small, fanless, and cheap. I paid about $222 for fully integrated MB, CD-ROM and case from http://www.computergate.com/ ). FreeBSD 4.7 has worked well on this hardware with a few exceptions. Currently I'm experiencing a critical problem that leaves my computer unusable after just an hour or so of uptime. There appears to a problem with hard disk writes, followed by immediate failure of my USB keyboard to work. Here's what the logs report: ### Dec 18 18:53:14 asana /kernel: ad1: WRITE command timeout tag=0 serv=0 - resetting Dec 18 18:53:49 asana /kernel: ata0: resetting devices .. done Dec 18 18:53:49 asana /kernel: ad1: WRITE command timeout tag=0 serv=0 - resetting Dec 18 18:53:49 asana /kernel: ata0: resetting devices .. done Dec 18 18:53:49 asana /kernel: ad1: WRITE command timeout tag=0 serv=0 - resetting Dec 18 18:53:49 asana /kernel: ata0: resetting devices .. done Dec 18 18:53:49 asana /kernel: ad1: WRITE command timeout tag=0 serv=0 - resetting Dec 18 18:53:49 asana /kernel: ad1: timeout waiting for cmd=ef s=d0 e=00 Dec 18 18:53:49 asana /kernel: ad1: trying fallback to PIO mode Dec 18 18:53:49 asana /kernel: ata0: resetting devices .. done Dec 18 18:56:21 asana /kernel: uhub1: at uhub0 port 2 (addr 2) disconnected Dec 18 18:56:21 asana /kernel: ukbd0: detached Dec 18 18:56:31 asana /kernel: uhub1: detached Dec 18 18:58:45 asana /kernel: uhub0: port error, restarting port 2 Dec 18 18:59:06 asana /kernel: uhub0: device problem, disabling port 1 ### What's happening with the USB related entries there is that I have un-plugged and re-plugged the keyboard, but it won't recognize it at this point. My "dmesg" output is attached for full system details. Here are some additional notes: - The drive is brand new, attached with new 80 wire IDE cables. - I've been trying to get APM to work, specifically get the hard drive to spin down. I never got that to work, and eventually tried disabling APM in kernel.conf and rc.conf. Either way, these desk errors still happen. - My USB keyboard (the "Happy Hacking" keyboard), has exhibited other weird behavior before. At least once, some weird characters were ghost-typed into the terminal window I was working in, and then the computer rebooted with a kernel panic. Another time, the keyboard registered the same key press over and over, even though the key wasn't being pressed. I use the exact same model on a Mac at work without problems. - My computer dual-boots into Linux. I could try testing with it for comparison, though I'd prefer to get this fixed and keep using FreeBSD. Thanks for any suggestions! -mark http://mark.stosberg.com/ Copyright (c) 1991-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.7-RELEASE #0: Wed Dec 18 19:40:55 EST 2002 root@asana.summersault.com:/usr/src/sys/compile/ASANA_EDEN-2002-12-18 Timecounter "i8254" frequency 1193182 Hz CPU: VIA C3 Samuel 2 (533.36-MHz 686-class CPU) Origin = "CentaurHauls" Id = 0x673 Stepping = 3 Features=0x803035<FPU,DE,TSC,MSR,MTRR,PGE,MMX> real memory = 260046848 (253952K bytes) config> enable apm avail memory = 249487360 (243640K bytes) Preloaded elf kernel "kernel" at 0xc037e000. Preloaded userconfig_script "/boot/kernel.conf" at 0xc037e09c. Preloaded elf module "snd_via82c686.ko" at 0xc037e0ec. Preloaded elf module "snd_pcm.ko" at 0xc037e194. md0: Malloc disk Using $PIR table, 5 entries at 0xc00fdc70 apm0: <APM BIOS> on motherboard apm: found APM BIOS v1.2, connected at v1.2 npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Host to PCI bridge> on motherboard pci0: <PCI bus> on pcib0 pcib1: <PCI to PCI bridge (vendor=1106 device=8601)> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pci1: <Trident model 8500 VGA-compatible display device> at 0.0 irq 10 isab0: <PCI to ISA bridge (vendor=1106 device=8231)> at device 17.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <VIA 8231 ATA100 controller> port 0xd000-0xd00f at device 17.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 3 at device 17.2 on pci0 usb0: <VIA 83C572 USB controller> on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhub1: Chicony Generic USB Hub, class 9/0, rev 1.10/1.00, addr 2 uhub1: 1 port with 0 removable, bus powered ukbd0: Chicony PFU-65 USB Keyboard, rev 1.10/1.00, addr 3, iclass 3/1 kbd0 at ukbd0 uhci1: <VIA 83C572 USB controller> port 0xd800-0xd81f irq 3 at device 17.3 on pci0 usb1: <VIA 83C572 USB controller> on uhci1 usb1: USB revision 1.0 uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered chip1: <PCI to Other bridge (vendor=1106 device=8235)> at device 17.4 on pci0 pcm0: <VIA VT82C686A> port 0xe400-0xe403,0xe000-0xe003,0xdc00-0xdcff irq 5 at device 17.5 on pci0 vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xe800-0xe8ff mem 0xe4001000-0xe40010ff irq 10 at device 18.0 on pci0 vr0: Ethernet address: 00:40:63:c1:1a:5f miibus0: <MII bus> on vr0 ukphy0: <Generic IEEE 802.3u media interface> on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xec00-0xec7f mem 0xe4000000-0xe400007f irq 11 at device 20.0 on pci0 xl0: Ethernet address: 00:01:02:bd:77:24 miibus1: <MII bus> on xl0 xlphy0: <3Com internal media interface> on miibus1 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto orm0: <Option ROMs> at iomem 0xc0000-0xcbfff,0xcc000-0xcffff,0xd0000-0xd97ff on isa0 fdc0: ready for input in output fdc0: cmd 3 failed at out byte 1 of 3 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: configured irq 3 not in bitmap of probed irqs 0 ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 ad1: 19073MB <WDC WD200BB-75CAA0> [38752/16/63] at ata0-slave UDMA100 acd0: CDROM <SR244W> at ata1-master PIO4 Mounting root from ufs:/dev/ad1s1a WARNING: / was not properly dismounted To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-hardware" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.51.0212191905230.8899>