Date: Sun, 29 Aug 2004 18:05:48 +0200 (CEST) From: Gheorghe Ardelean <ardelean@ww.uni-erlangen.de> To: <ticso@cicely.de> Cc: freebsd-alpha@freebsd.org Subject: Re: 5.3-BETA1 for Alpha available Message-ID: <Pine.LNX.4.33.0408291755430.26321-100000@servww6.ww.uni-erlangen.de> In-Reply-To: <20040829131149.GA59909@cicely12.cicely.de>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi,
> Mmm - it's dereferencing nonsense.
> Guess this bug is old and just triggered as a result of the timeout.
> I'm missing an IRQ in the probe, so the timeout is reasonable.
> Normaly we should see:
> sym0: interrupting at ISA irq 11
> A complete boot -v output would be interessting to see routing
> decisions - sounds much like someone broke IRQ routing on alpha.
> LCA based alphas are the only alphas so far that we have enabled
> interrupt routing and possibly the only alphas that share ISA and PCI
> interrupts.
I've tried to do the boot -v and the interesting thing is that it worked
up to the instalation point! The VGA card is a Matrox Millenium PCI (but
I am using a serial console)! Here is the output:
CPU 0 speed is 6.00 ns (167MHz)
Powerup process has started
CPU ID = 0
Initialize configuration locks etc.
Configure the memory
Initialising ISA/PCI interrupts.
Configure the PCI Bus
Start tt class, port (graphics, keyboard, then serial) drivers
entering idle loop
change stdin/out/err channels from nl to tt
Memory size = 96Mbytes
testing memory from 800000 to 5e16000 ...
Start driver phase 4
access NVRAM
Build this processor's slot in the hwrpb
Backup Cache size = 256Kb
Init SCSI class driver
Start driver phase 5
AXPpci33 Common Console X4.7-1860, built on Nov 1 1996 at 06:00:01
>>>show dev
dkb200.2.0.12.0 DKB200 TOSHIBA CD-ROM XM-5701TA 1557
dkb400.4.0.12.0 DKB400 FUJITSU M2684S-512 2035
dkb600.6.0.12.0 DKB600 SEAGATE ST3600N 8394
dva0.0.0.0.1 DVA0
ewa0.0.0.8.0 EWA0 00-E0-29-15-23-70
pka0.7.0.6.0 PKA0 SCSI Bus ID 7
pkb0.7.0.12.0 PKB0 SCSI Bus ID 7
>>>boot dkb200
(boot dkb200.2.0.12.0 -flags 0)
block 0 of dkb200.2.0.12.0 is a valid boot block
reading 409 blocks from dkb200.2.0.12.0
bootstrap code read in
base = 110000, image_start = 0, image_bytes = 33200
initializing HWRPB at 2000
initializing page table at 102000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Console: SRM firmware console
VMS PAL rev: 0x1000400010538
OSF PAL rev: 0x100090002012d
Switch to OSF PAL code succeeded.
FreeBSD/alpha SRM CD9660 boot, Revision 1.2
(root@ds10.wbnet, Mon Aug 23 08:53:04 UTC 2004)
Memory: 98304 k
OK boot -v
Entering /boot/kernel/kernel at 0xfffffc0000347100...
Unrecognized boot flag '0'.
GDB: debug ports: sio
GDB: current port: sio
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.3-BETA1 #0: Mon Aug 23 22:50:09 UTC 2004
root@ds10.wbnet:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xfffffc0000e02000.
Preloaded mfs_root "/boot/mfsroot" at 0xfffffc0000e020e0.
DEC AXPpci
Alpha PC AXPpci33, 166MHz
8192 byte page size, 1 processor.
CPU: LCA Family major=4 minor=2
OSF PAL rev: 0x100090002012d
real memory = 98590720 (94 MB)
Physical memory chunk(s):
0x00e24000 - 0x05d8dfff, 83271680 bytes (10165 pages)
avail memory = 81739776 (77 MB)
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
mem: <memory>
lca0: <21066 Core Logic chipset>
pcib0: <21066 PCI host bus adapter> on lca0
pci0: <PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 4, range 32, base 00010100, size 8, enabled
map[14]: type 1, range 32, base 81854100, size 8, enabled
found-> vendor=0x1000, dev=0x0001, revid=0x01
bus=0, slot=6, func=0
class=00-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0047, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0xff (7650 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
found-> vendor=0x8086, dev=0x0484, revid=0x03
bus=0, slot=7, func=0
class=00-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 4, range 32, base 00010200, size 7, enabled
map[14]: type 1, range 32, base 81854200, size 7, enabled
found-> vendor=0x1011, dev=0x0014, revid=0x21
bus=0, slot=8, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0047, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0xff (7650 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
map[10]: type 3, range 32, base 88000000, size 24, enabled
map[14]: type 1, range 32, base 81850000, size 14, enabled
map[18]: type 1, range 32, base 81000000, size 23, enabled
found-> vendor=0x102b, dev=0x051b, revid=0x00
bus=0, slot=11, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0xf8 (7440 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
map[10]: type 4, range 32, base 00010000, size 8, enabled
map[14]: type 1, range 32, base 81854000, size 8, enabled
found-> vendor=0x1000, dev=0x0001, revid=0x23
bus=0, slot=12, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0047, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0xff (7650 ns), mingnt=0x08 (2000 ns), maxlat=0x40 (16000
ns)
intpin=a, irq=255
powerspec 1 supports D0 D3 current D0
sym0: <810> port 0x10100-0x101ff mem 0x81854100-0x818541ff at device 6.0
on pci0
sym0: Reserved 0x100 bytes for rid 0x14 type 3 at 0x81854100
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: open drain IRQ line driver
sym0: using NCR-generic firmware.
sym0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 00/00/00/00/00/00
sym0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 03/c8/00/00/08/00
sym0: Delay (GEN=11): 232 msec, 38311 KHz
sym0: Delay (GEN=11): 277 msec, 32087 KHz
sym0: Delay (GEN=11): 277 msec, 32087 KHz
sym0: interrupting at ISA irq 11
sym0: [GIANT-LOCKED]
PCI-ISA bridge with incorrect subclass 0x0
PCI-ISA bridge with incorrect subclass 0x0
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
de0: <Digital 21041 Ethernet> port 0x10200-0x1027f mem
0x81854200-0x8185427f at device 8.0 on pci0
de0: Reserved 0x80 bytes for rid 0x14 type 3 at 0x81854200
de0: interrupting at ISA irq 5
de0: [GIANT-LOCKED]
de0: SMC 21041 [10Mb/s] pass 2.1
de0: bpf attached
de0: Ethernet address: 00:e0:29:15:23:70
pci0: <display, VGA> at device 11.0 (no driver attached)
sym1: <810a> port 0x10000-0x100ff mem 0x81854000-0x818540ff at device 12.0
on pci0
sym1: Reserved 0x100 bytes for rid 0x14 type 3 at 0x81854000
sym1: Symbios NVRAM, ID 7, Fast-10, SE, parity checking
sym1: open drain IRQ line driver
sym1: using LOAD/STORE-based firmware.
sym1: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 00/00/00/00/00/00
sym1: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 03/ce/a0/01/08/00
sym1: Delay (GEN=11): 242 msec, 36728 KHz
sym1: Delay (GEN=11): 277 msec, 32087 KHz
sym1: Delay (GEN=11): 277 msec, 32087 KHz
sym1: interrupting at ISA irq 10
sym1: [GIANT-LOCKED]
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
ata0 at port 0x3f6,0x1f0-0x1f7 irq 14 on isa0
ata0: reset tp1 mask=00 ostat0=ff ostat1=ff
ata0: interrupting at ISA irq 14
ata0: [MPSAFE]
ata1 at port 0x376,0x170-0x177 irq 15 on isa0
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ata1: interrupting at ISA irq 15
ata1: [MPSAFE]
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0: atkbd0, generic (0), config:0x0, flags:0x1f0000
atkbd0: interrupting at ISA irq 1
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0061
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: interrupting at ISA irq 6
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0
Calibrating clock(s) ... PCC clock: 167005489 Hz (firmware 166666666 Hz)
i8254 clock: 1193178 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <Parallel port> at port 0x3bc-0x3c3 irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Polled port
ppi0: <Parallel I/O> on ppbus0
ppc0: interrupting at ISA irq 7
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x0>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0 0 0 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio0: interrupting at ISA irq 4
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0 0 0 0
sio1 at port 0x2f8-0x2ff irq 3 flags 0x80 on isa0
sio1: type 16550A
sio1: interrupting at ISA irq 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xb8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 60 4f 50 83 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 67 60 4f 50 83 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff
isa_probe_children: probing PnP devices
procfs registered
Timecounter "i8254" frequency 1193182 Hz quality 0
Timecounter "alpha" frequency 167005489 Hz quality 0
Timecounters tick every 0.976 msec
lo0: bpf attached
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
(noperiph:sym1:0:-1:-1): SCSI BUS reset delivered.
md0: Preloaded image </boot/mfsroot> 4423680 bytes at 0xfffffc00009c63d8
GEOM: Configure md0a, start 8192 length 4415488 end 4423679
GEOM: Configure md0c, start 0 length 4423680 end 4423679
(probe11:sym1:0:4:0): Retrying Command
(probe9:sym1:0:2:0): Retrying Command
(probe9:sym1:0:2:0): error 22
(probe9:sym1:0:2:0): Unretryable Error
pass0 at sym1 bus 0 target 2 lun 0
pass0: <TOSHIBA CD-ROM XM-5701TA 1557> Removable CD-ROM SCSI-2 device
pass0: 10.000MB/s transfers (10.000MHz, offset 8)
pass1 at sym1 bus 0 target 4 lun 0
pass1: <FUJITSU M2684S-512 2035> Fixed Direct Access SCSI-2 device
pass1: Serial Number 00090868
pass1: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
pass2 at sym1 bus 0 target 6 lun 0
pass2: <SEAGATE ST3600N 8394> Fixed Direct Access SCSI-2 device
pass2: Serial Number 00882508
pass2: 10.000MB/s transfers (10.000MHz, offset 8)
cd0 at sym1 bus 0 target 2 lun 0
cd0: <TOSHIBA CD-ROM XM-5701TA 1557> Removable CD-ROM SCSI-2 device
cd0: 10.000MB/s transfers (10.000MHz, offset 8)
cd0: cd present [141295 x 2048 byte records]
da0 at sym1 bus 0 target 4 lun 0
da0: <FUJITSU M2684S-512 2035> Fixed Direct Access SCSI-2 device
da0: Serial Number 00090868
da0: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
da0: 507MB (1039329 512 byte sectors: 64H 32S/T 507C)
da1 at sym1 bus 0 target 6 lun 0
da1: <SEAGATE ST3600N 8394> Fixed Direct Access SCSI-2 device
da1: Serial Number 00882508
da1: 10.000MB/s transfers (10.000MHz, offset 8)
da1: 499MB (1023484 512 byte sectors: 64H 32S/T 499C)
GEOM: new disk cd0
GEOM: new disk da0
GEOM: new disk da1
GEOM: Configure da0a, start 0 length 263192576 end 263192575
GEOM: Configure da0b, start 263192576 length 268943872 end 532136447
GEOM: Configure da0c, start 0 length 532136448 end 532136447
GEOM: Configure da1c, start 0 length 524023808 end 524023807
GEOM: Configure da1e, start 0 length 524023808 end 524023807
Mounting root from ufs:/dev/md0
WARNING: clock gained 7310 days -- CHECK AND RESET THE DATE!
start_init: trying /sbin/init
start_init: trying /sbin/oinit
start_init: trying /sbin/init.bak
start_init: trying /stand/sysinstall
/stand/sysinstall running as init on serial console
These are the predefined terminal types available to
sysinstall when running stand-alone. Please choose the
closest match for your particular terminal.
1 ...................... Standard ANSI terminal.
2 ...................... VT100 or compatible terminal.
3 ...................... FreeBSD system console (color).
4 ...................... FreeBSD system console (monochrome).
5 ...................... xterm terminal emulator.
Your choice: (1-5)
=======
Tomorrow I will try also the AlphaPC64 with Matrox VGA inseatd of S3
Virge.
Regards,
G. Ardelean
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.LNX.4.33.0408291755430.26321-100000>