Date: Sun, 19 Dec 2004 15:24:35 +0100 From: Daniel Graupner <listen@danielgraupner.de> To: freebsd-acpi@freebsd.org Subject: Re: S3 on Dell laptops.. Message-ID: <41C58F23.2070005@danielgraupner.de>
next in thread | raw e-mail | index | archive | help
>Prior to today, I've been running 5.3-RELEASE on a Dell laptop. Only
>one power save mode worked for me, S1.
>Today, I updated my src tree, and sucked in the recently posted acpi
>patches and rebuilt world.
>Prior to doing that, attempting to go into S3 would result in immediate
>reboot, whereas now, it actually begins to run the disk, blank the
>screen, and THEN reboots. So progress has been made :)
I have a Dell Inspiron 510m and experienced the same problems. Everything worked fine with 5.2.1,
but with 5.1 only S1 works.
Here is some additional info from my machine, hope you can fix this.
Regards, Daniel.
mars@~:sysctl hw.acpi
hw.acpi.supported_sleep_state: S1 S3 S4 S5
hw.acpi.power_button_state: S5
hw.acpi.sleep_button_state: S1
hw.acpi.lid_switch_state: NONE
hw.acpi.standby_state: S1
hw.acpi.suspend_state: S3
hw.acpi.sleep_delay: 1
hw.acpi.s4bios: 1
hw.acpi.verbose: 0
hw.acpi.reset_video: 1
hw.acpi.cpu.throttle_max: 8
hw.acpi.cpu.throttle_state: 8
hw.acpi.cpu.cx_supported: C1/1 C2/1 C3/85 C4/185
hw.acpi.cpu.cx_lowest: C4
hw.acpi.cpu.cx_usage: 0.00% 100.00% 0.00% 0.00%
hw.acpi.thermal.min_runtime: 0
hw.acpi.thermal.polling_rate: 10
hw.acpi.thermal.tz0.temperature: 49.5C
hw.acpi.thermal.tz0.active: -1
hw.acpi.thermal.tz0.thermal_flags: 0
hw.acpi.thermal.tz0._PSV: -1
hw.acpi.thermal.tz0._HOT: -1
hw.acpi.thermal.tz0._CRT: 101.0C
hw.acpi.thermal.tz0._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1
hw.acpi.acline: 1
hw.acpi.battery.life: 100
hw.acpi.battery.time: -1
hw.acpi.battery.state: 0
hw.acpi.battery.units: 2
hw.acpi.battery.info_expire: 5
mars@~:dmesg
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.3-STABLE #1: Sun Dec 19 12:03:44 CET 2004
root@mars:/usr/obj/usr/src/sys/DAEL
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) M processor 1.70GHz (1698.56-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6d6 Stepping = 6
Features=0xafe9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,P
BE>
real memory = 535470080 (510 MB)
avail memory = 514310144 (490 MB)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL CPi R > on motherboard
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU (4 Cx states)> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_cmbat1: <Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI link \\_SB_.PCI0.LNKB has invalid initial irq 11, ignoring
pci0: <ACPI PCI bus> on pcib0
pci0: <base peripheral> at device 0.1 (no driver attached)
pci0: <base peripheral> at device 0.3 (no driver attached)
agp0: <Intel 82855GME (855GME GMCH) SVGA controller> port 0xc000-0xc007 mem
0xfaf80000-0xfaffffff,0xf0000000-0xf7ffffff i
rq 11 at device 2.0 on pci0
agp0: detected 892k stolen memory
agp0: aperture size is 128M
pci0: <display> at device 2.1 (no driver attached)
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xbf80-0xbf9f irq 11 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xbf40-0xbf5f irq 11 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ums0: vendor 0x1241 product 0x1177, rev 1.10/2.00, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xbf20-0xbf3f irq 11 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib1
cbb0: <TI4510 PCI-CardBus Bridge> at device 1.0 on pci1
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fwohci0: <1394 Open Host Controller Interface> mem 0xfcff8000-0xfcffbfff,0xfcfff800-0xfcffffff irq
11 at device 1.1 on pc
i1
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 33:4f:c0:00:02:8c:a0:30
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 32:4f:c0:8c:a0:30
fwe0: Ethernet address: 32:4f:c0:8c:a0:30
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
pci1: <network> at device 3.0 (no driver attached)
fxp0: <Intel 82801DB (ICH4) Pro/100 VE Ethernet> port 0xecc0-0xecff mem 0xfcffd000-0xfcffdfff irq 11
at device 8.0 on pci
1
miibus0: <MII bus> on fxp0
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:0f:1f:c2:08:a9
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port 0xbfa0-0xbfaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at
device 31.1 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
pcm0: <Intel ICH4 (82801DB)> port 0xdc40-0xdc7f,0xd800-0xd8ff mem
0xfaeff400-0xfaeff4ff,0xfaeff800-0xfaeff9ff irq 5 at de
vice 31.5 on pci0
pcm0: [GIANT-LOCKED]
pcm0: <SigmaTel STAC9750/51 AC97 Codec>
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model GlidePoint, device ID 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ppc0: <ECP parallel printer port> port 0x778-0x77b,0x378-0x37f irq 7 drq 1 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
orm0: <ISA Option ROMs> at iomem
0xcf800-0xcffff,0xcf000-0xcf7ff,0xce800-0xcefff,0xce000-0xce7ff,0xcd800-0xcdfff,0xc0000-
0xcd7ff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1698563078 Hz quality 800
Timecounters tick every 10.000 msec
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
cpu0: Performance states changed
ad0: 38154MB <HTS548040M9AT00/MG2OA53A> [77520/16/63] at ata0-master UDMA100
acd0: CDRW <NEC DVD+RW ND-6100A/104D> at ata1-master UDMA33
...
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?41C58F23.2070005>