Date: Sat, 08 Oct 2005 07:13:36 +0100 From: Jayton Garnett <jay@codegurus.org> To: freebsd-stable@freebsd.org Subject: acpi_bus_number: can't get _ADR Message-ID: <43476390.4010806@codegurus.org>
next in thread | raw e-mail | index | archive | help
Hello, I have recently upgraded my system (hardware wise). I bought: Foxconn/Winfast motherboard with the nForce 4 (CK8-04 standard) http://www.foxconnchannel.com/products_motherboard_2.cfm?pName=NF4K8AC-8EKRS AMD Athlon 64 3000+ 1GB DDR400 ATi X300SE 128mb PCI-E When I booted my 32bit FreeBSD 5.4-P7 (only ever upgraded the kernel) I noticed this message: acpi_bus_number: can't get _ADR I searched the archives and found this in the 6-betas (so far) Does anybody know what this means and how to sort it out? Should I worry about it or forget about it? Could this message have something to do with the fact I plugged a 20-pin ATX power connector into a 24-pin ATX power connector on the motherboard, The motherboard manual says that you can but they recommend using a 24-pin connector. (Cant see me buying a new PSU that has 24pin ATX connectors just yet as they cost £££/$$$'s, but will pickup a convertor soon) Please see below for a full dmseg output. Cheers, Jayton desktop# dmesg Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.4-RELEASE-p7 #1: Sun Sep 18 16:01:22 BST 2005 jay@desktop.jayton.plus.com:/usr/src/sys/i386/compile/UBERHACKER Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: AMD Athlon(tm) 64 Processor 3000+ (1808.34-MHz 686-class CPU) Origin = "AuthenticAMD" Id = 0x20ff0 Stepping = 0 Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2> AMD Features=0xe0500000<NX,AMIE,LM,DSP,3DNow!> real memory = 1073676288 (1023 MB) avail memory = 1041092608 (992 MB) ACPI APIC Table: <Nvidia AWRDACPI> ioapic0 <Version 1.1> irqs 0-23 on motherboard npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <Nvidia AWRDACPI> on motherboard acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR acpi0: Power Button (fixed) acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 cpu0: <ACPI CPU> port 0x530-0x537 on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 ACPI link \\_SB_.PCI0.APC3 has invalid initial irq 7, ignoring ACPI link \\_SB_.PCI0.APC4 has invalid initial irq 5, ignoring pci0: <ACPI PCI bus> on pcib0 pci0: <memory> at device 0.0 (no driver attached) isab0: <PCI-ISA bridge> at device 1.0 on pci0 isa0: <ISA bus> on isab0 pci0: <serial bus, SMBus> at device 1.1 (no driver attached) ohci0: <OHCI (generic) USB controller> mem 0xfebff000-0xfebfffff irq 22 at device 2.0 on pci0 usb0: OHCI version 1.0, legacy support usb0: SMM does not respond, resetting usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 10 ports with 10 removable, self powered pci0: <serial bus, USB> at device 2.1 (no driver attached) pcm0: <nVidia nForce4> port 0xec00-0xecff,0xf000-0xf0ff mem 0xfebfd000-0xfebfdfff irq 20 at device 4.0 on pci0 pcm0: <Avance Logic ALC655 AC97 Codec> atapci0: <nVidia nForce4 UDMA133 controller> port 0xe000-0xe00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 6.0 on pci0 ata0: channel #0 on atapci0 ata1: channel #1 on atapci0 atapci1: <GENERIC ATA controller> port 0xcc00-0xcc0f,0xb70-0xb73,0x970-0x977,0xbf0-0xbf3,0x9f0-0x9f7 irq 22 at device 7.0 on pci0 ata2: channel #0 on atapci1 ata3: channel #1 on atapci1 atapci2: <GENERIC ATA controller> port 0xb800-0xb80f,0xb60-0xb63,0x960-0x967,0xbe0-0xbe3,0x9e0-0x9e7 irq 21 at device 8.0 on pci0 ata4: channel #0 on atapci2 ata5: channel #1 on atapci2 pcib1: <ACPI PCI-PCI bridge> at device 9.0 on pci0 pci1: <ACPI PCI bus> on pcib1 ndis0: <OvisLink WL-8000PCI> mem 0xfe9c0000-0xfe9dffff,0xfe9fe000-0xfe9fffff irq 19 at device 7.0 on pci1 ndis0: NDIS API version: 5.1 ndis0: Ethernet address: 00:4f:62:01:2c:4e ndis0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps ndis0: 11g rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps pci0: <bridge> at device 10.0 (no driver attached) pcib2: <ACPI PCI-PCI bridge> at device 11.0 on pci0 pci2: <ACPI PCI bus> on pcib2 pcib3: <ACPI PCI-PCI bridge> at device 12.0 on pci0 pci3: <ACPI PCI bus> on pcib3 pcib4: <ACPI PCI-PCI bridge> at device 13.0 on pci0 pci4: <ACPI PCI bus> on pcib4 pcib5: <ACPI PCI-PCI bridge> at device 14.0 on pci0 pci5: <ACPI PCI bus> on pcib5 pci5: <display, VGA> at device 0.0 (no driver attached) pci5: <display> at device 0.1 (no driver attached) acpi_tz0: <Thermal Zone> port 0x530-0x537 on acpi0 fdc0: <floppy drive controller> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 pmtimer0 on isa0 orm0: <ISA Option ROMs> at iomem 0xcc000-0xcd7ff,0xc0000-0xcbfff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 ugen0: Logitech Camera, rev 1.10/1.00, addr 2 ums0: Acrox USB & PS/2 Mouse, rev 1.10/0.01, addr 3, iclass 3/1 ums0: 5 buttons and Z dir. Timecounter "TSC" frequency 1808342385 Hz quality 800 Timecounters tick every 10.000 msec ad0: 76319MB <WDC WD800BB-00JHA0/05.01C05> [155061/16/63] at ata0-master UDMA100ad1: 238475MB <WDC WD2500JB-00GVA0/08.02D08> [484521/16/63] at ata0-slave UDMA100 acd0: DVDR <ATAPI DVD RW 8XMax/130D> at ata1-slave PIO4 Mounting root from ufs:/dev/ad1s2a ndis0: link up
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?43476390.4010806>