Date: Mon, 27 May 2002 08:29:07 +0400 From: Alex Deiter <tiamat@komi.mts.ru> To: "David O'Brien" <obrien@FreeBSD.ORG> Cc: freebsd-sparc@FreeBSD.ORG Subject: problem with gem on receive: MAC rx fault, status 3 Message-ID: <106342023423.20020527082907@komi.mts.ru> In-Reply-To: <20020526083846.B8434@dragon.nuxi.com> References: <616092620.20020523092222@komi.mts.ru> <20020526083846.B8434@dragon.nuxi.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Hello David,
Sunday, May 26, 2002, 7:38:46 PM, you wrote:
>> > \
>> \: unknown command
>> ^^^^^^^^^^^^^^^^^^^
>> >>>> Why there is this error?
DOB> The loader does not have Ficl support yet, and thus cannot properly
DOB> interrupt one of the start up scripts. You can ignore this "error"; it
DOB> hurts nothing right now.
Thanks!
On Netra T1 installed two 10/100 Mbps ethernet ports. Why one is accessible only?
severina# ifconfig -l
gem0 lo0 ppp0
What to do with an error 'MAC rx fault, status 3' ?
# dmesg |egrep 'phy|gem'
gem0: <Sun ERI 10/100 Ethernet Adaptor> mem 0xe0400000-0xe041ffff irq 6 at devic
e 12.1 on pci2
miibus0: <MII bus> on gem0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
gem0: Ethernet address: 00:03:ba:13:30:71
using internal phy
# ifconfig gem0
gem0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 10.50.1.9 netmask 0xffffff00 broadcast 10.50.1.255
ether 00:03:ba:13:30:71
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
ftp> get ports.tar.bz2
local: ports.tar.bz2 remote: ports.tar.bz2
229 Entering Extended Passive Mode (|||49385|)
150 Opening BINARY mode data connection for 'ports.tar.bz2' (52432031 bytes).
0% | | 0 0.00 KB/s --:-- ETAM
AC rx fault, status 3
16% |***** | 8608 KB 3.99 MB/s 00:10 ETAM
AC rx fault, status 3
23% |******** | 12115 KB 3.82 MB/s 00:09 ETAM
AC rx fault, status 2
30% |*********** | 15516 KB 3.69 MB/s 00:09 ETAM
AC rx fault, status 3
30% |*********** | 15574 KB 2.50 MB/s 00:13 ETAM
AC rx fault, status 3
32% |*********** | 16854 KB 2.31 MB/s 00:14 ETAM
AC rx fault, status 3
35% |************ | 18138 KB 2.18 MB/s 00:14 ETAM
AC rx fault, status 3
41% |*************** | 21100 KB 2.26 MB/s 00:12 ETAM
AC rx fault, status 3
43% |*************** | 22345 KB 1.96 MB/s 00:14 ETAM
AC rx fault, status 3
58% |********************* | 30119 KB 1.62 MB/s 00:12 ETAM
AC rx fault, status 3
59% |********************* | 30210 KB 1.27 MB/s 00:16 ETAM
AC rx fault, status 3
72% |************************** | 37271 KB 1.44 MB/s 00:09 ETAM
AC rx fault, status 3
87% |******************************** | 44727 KB 1.61 MB/s 00:03 ETAM
AC rx fault, status 3
87% |******************************** | 44787 KB 1.55 MB/s 00:04 ETAM
AC rx fault, status 3
92% |********************************** | 47401 KB 1.58 MB/s 00:02 ETAM
AC rx fault, status 3
100% |*************************************| 51203 KB 1.60 MB/s 00:00 ETA
100% |*************************************| 51203 KB 1.60 MB/s 00:00 ETA2
26 Transfer complete.
52432031 bytes received in 00:31 (1.59 MB/s)
Thanks!
--
Best regards,
Alex mailto:tiamat@komi.mts.ru
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-sparc" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?106342023423.20020527082907>