Date: Sat, 1 Jun 2002 13:31:31 +0300 From: Ruslan Ermilov <ru@FreeBSD.org> To: Soren Schmidt <sos@FreeBSD.org> Cc: qa@FreeBSD.org Subject: acd0: MODE_SENSE_BIG command timeout - resetting Message-ID: <20020601103131.GA59274@sunbay.com>
next in thread | raw e-mail | index | archive | help
Hi!
This is the completely new box, on which the minimal standard
4.5-RELEASE was installed. In a blind attempt to have my sis0
card working, I attempted to upgrade it to 4.6-RC. After the
new 4.6-RC kernel was installed, "atacd" started complaining
with "MODE_SENSE_BIG command timeout - resetting" on boot.
This is the pristine machine, no /boot/loader.conf settings,
etc. This machine also happens to preserve the dmesg buffer
between reboots, so what follows is dmesg from 4.5-RELEASE
kernel run, and then reboot after the 4.6-RC kernel was
installed. Any highlights?
Soren, if this is a known issue, just tell me and I will
shut up and wait for the better days.
$ sysctl hw.ata
hw.ata.ata_dma: 1
hw.ata.wc: 1
hw.ata.tags: 0
hw.ata.atapi_dma: 0
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-RELEASE #0: Mon Jan 28 14:31:56 GMT 2002
murray@builder.freebsdmall.com:/usr/src/sys/compile/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium 4 (1614.38-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf12 Stepping = 2
Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,<b28>,ACC>
real memory = 251641856 (245744K bytes)
avail memory = 240136192 (234508K bytes)
Preloaded elf kernel "kernel" at 0xc0496000.
md0: Malloc disk
Using $PIR table, 6 entries at 0xc00f1970
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib2: <PCI to PCI bridge (vendor=1039 device=0001)> at device 1.0 on pci0
pci1: <PCI bus> on pcib2
pci1: <SiS model 6325 VGA-compatible display device> at 0.0 irq 11
isab0: <SiS 85c503 PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
ohci0: <SiS 5571 USB controller> mem 0xe7000000-0xe7000fff irq 12 at device 2.2 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <SiS 5571 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ohci1: <SiS 5571 USB controller> mem 0xe6800000-0xe6800fff irq 12 at device 2.3 on pci0
usb1: OHCI version 1.0, legacy support
usb1: <SiS 5571 USB controller> on ohci1
usb1: USB revision 1.0
uhub1: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
atapci0: <SiS 5591 ATA100 controller> port 0xb800-0xb80f at device 2.5 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x1039, dev=0x7012) at 2.7 irq 10
sis0: <SiS 900 10/100BaseTX> port 0xa000-0xa0ff mem 0xe6000000-0xe6000fff irq 10 at device 3.0 on pci0
sis0: Ethernet address: 00:e0:18:64:bb:d3
sis0: MII without any PHY!
device_probe_and_attach: sis0 attach returned 6
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x9800-0x983f mem 0xe5000000-0xe50fffff,0xe5800000-0xe5800fff irq 12 at device 16.0 on pci0
fxp0: Ethernet address 00:90:27:75:55:4f
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib1: <SiS 5591 host to AGP bridge> on motherboard
pci2: <PCI bus> on pcib1
orm0: <Option ROMs> at iomem 0xc0000-0xcbfff,0xcc000-0xccfff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 76319MB <ST380021A> [155061/16/63] at ata0-master UDMA100
acd0: CDROM <SONY CD-ROM CDU523 1> at ata1-master using PIO4
Mounting root from ufs:/dev/ad0a
Waiting (max 60 seconds) for system process `vnlru' to stop...stopped
Waiting (max 60 seconds) for system process `bufdaemon' to stop...stopped
Waiting (max 60 seconds) for system process `syncer' to stop...stopped
syncing disks... 4
done
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.6-RC #0: Sat Jun 1 19:19:36 GMT 2002
install@harbour.sunbay.com.au:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium 4 (1614.39-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf12 Stepping = 2
Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,<b28>,ACC>
real memory = 251641856 (245744K bytes)
avail memory = 239865856 (234244K bytes)
Preloaded elf kernel "kernel" at 0xc04d8000.
md0: Malloc disk
Using $PIR table, 6 entries at 0xc00f1970
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib2: <PCI to PCI bridge (vendor=1039 device=0001)> at device 1.0 on pci0
pci1: <PCI bus> on pcib2
pci1: <SiS model 6325 VGA-compatible display device> at 0.0 irq 11
isab0: <SiS 85c503 PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
ohci0: <SiS 5571 USB controller> mem 0xe7000000-0xe7000fff irq 12 at device 2.2 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <SiS 5571 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ohci1: <SiS 5571 USB controller> mem 0xe6800000-0xe6800fff irq 12 at device 2.3 on pci0
usb1: OHCI version 1.0, legacy support
usb1: <SiS 5571 USB controller> on ohci1
usb1: USB revision 1.0
uhub1: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
atapci0: <SiS 5591 ATA100 controller> port 0xb800-0xb80f at device 2.5 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x1039, dev=0x7012) at 2.7 irq 10
sis0: <SiS 900 10/100BaseTX> port 0xa000-0xa0ff mem 0xe6000000-0xe6000fff irq 10 at device 3.0 on pci0
sis0: Ethernet address: 00:e0:18:64:bb:d3
sis0: MII without any PHY!
device_probe_and_attach: sis0 attach returned 6
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x9800-0x983f mem 0xe5000000-0xe50fffff,0xe5800000-0xe5800fff irq 12 at device 16.0 on pci0
fxp0: Ethernet address 00:90:27:75:55:4f
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib1: <SiS 5591 host to AGP bridge> on motherboard
pci2: <PCI bus> on pcib1
orm0: <Option ROMs> at iomem 0xc0000-0xcbfff,0xcc000-0xccfff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 76319MB <ST380021A> [155061/16/63] at ata0-master UDMA100
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done
acd0: CDROM <SONY CD-ROM CDU523 1> at ata1-master PIO4
Mounting root from ufs:/dev/ad0a
--
Ruslan Ermilov Sysadmin and DBA,
ru@sunbay.com Sunbay Software AG,
ru@FreeBSD.org FreeBSD committer,
+380.652.512.251 Simferopol, Ukraine
http://www.FreeBSD.org The Power To Serve
http://www.oracle.com Enabling The Information Age
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-qa" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020601103131.GA59274>