Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 11 Oct 2004 05:55:24 +0700
From:      Muhammad Reza <reza@mra.co.id>
To:        grog@freebsd.org
Cc:        freebsd-questions@freebsd.org
Subject:   Re: RAID 1 in HP NetServer LC 2000
Message-ID:  <4169BDDC.20500@mra.co.id>
In-Reply-To: <200410092122.25811.Emanuel.Strobl@gmx.net>
References:  <41669A62.9040700@mra.co.id> <200410092122.25811.Emanuel.Strobl@gmx.net>

next in thread | previous in thread | raw e-mail | index | archive | help
Ok.. vinum then..
but i have error when applied this vinum.conf

drive drive1 device /dev/da0s1e
drive drive2 device /dev/da1s1e
 volume usr setupstate
  plex org concat
    sd length 13887091s drive drive1
  plex org concat
    sd length 13887091s drive drive2
 volume var setupstate
  plex org concat
    sd length 0 drive drive1
  plex org concat
    sd length 0 drive drive2

mail# vinum
vinum -> create -f /etc/vinum.conf
   2: drive drive2 device /dev/da1s1e
/*** 2 : Invalid argument*/
1 drives:
D drive1                State: up       Device /dev/da0s1e      Avail: 
0/16488 MB (0%)
D drive2                State: referenced       Device /dev/da1s1e      
Avail: 0/0 MB
 
2 volumes:
V usr                   State: up       Plexes:       2 Size:       6780 MB
V var                   State: up       Plexes:       2 Size:       9707 MB
 
4 plexes:
P usr.p0              C State: up       Subdisks:     1 Size:       6780 MB
P usr.p1              C State: up       Subdisks:     1 Size:       6780 MB
P var.p0              C State: up       Subdisks:     1 Size:       9707 MB
P var.p1              C State: up       Subdisks:     1 Size:          0  B
 
4 subdisks:
S usr.p0.s0             State: up       PO:        0  B Size:       6780 MB
S usr.p1.s0             State: up       PO:        0  B Size:       6780 MB
S var.p0.s0             State: up       PO:        0  B Size:       9707 MB
S var.p1.s0             State: up       PO:        0  B Size:          0  B

which argumen is invalid ? i use 4.10 ..
please help me...

regards
reza

>Am Freitag, 8. Oktober 2004 15:47 schrieb Muhammad Reza:
>  
>
>>Dear All,
>>Howto setup RAID 1 in HP NetServer LC 2000 ? I have 2 Seagate HDD that
>>want to be mirror 1:1,
>>Can i do that from Symbios software or tool from my FreeBSD 4.10 ?
>>    
>>
>
>With 4.10 you have the choice of vinum and ccd, in 5.3 you also have gmirror 
>for RAID1. See the man pages for details, ccd is quiet easy, vinum is a bit 
>more complex but more flexible too.
>
>-Harry
>
>  
>
>>regards
>>reza
>>---snip---
>>sym0: <896> port 0x2000-0x20ff mem
>>0xfd000000-0xfd001fff,0xfd002000-0xfd0023ff irq 11 at device 6.0 on pci3
>>sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
>>sym0: open drain IRQ line driver, using on-chip SRAM
>>sym0: using LOAD/STORE-based firmware.
>>sym0: handling phase mismatch from SCRIPTS.
>>sym1: <896> port 0x2400-0x24ff mem
>>0xfd004000-0xfd005fff,0xfd002400-0xfd0027ff irq 5 at device 6.1 on pci3
>>sym1: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
>>sym1: open drain IRQ line driver, using on-chip SRAM
>>sym1: using LOAD/STORE-based firmware.
>>sym1: handling phase mismatch from SCRIPTS.
>>---snap---
>>..
>>..
>>--snip--
>>da0 at sym1 bus 0 target 0 lun 0
>>da0: <SEAGATE ST318405LW 5063> Fixed Direct Access SCSI-3 device
>>da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
>>Enabled
>>da0: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
>>da1 at sym1 bus 0 target 1 lun 0
>>da1: <SEAGATE ST318405LW 5063> Fixed Direct Access SCSI-3 device
>>da1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
>>Enabled
>>da1: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
>>---snap---
>>
>>
>>
>>
>>
>>_______________________________________________
>>freebsd-questions@freebsd.org mailing list
>>http://lists.freebsd.org/mailman/listinfo/freebsd-questions
>>To unsubscribe, send any mail to
>>"freebsd-questions-unsubscribe@freebsd.org
>>
>"
>  
>



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4169BDDC.20500>