Date: Fri, 22 Jun 2012 14:21:04 -0700 From: Jack Vogel <jfvogel@gmail.com> To: Rick Miller <vmiller@hostileadmin.com> Cc: freebsd-stable@freebsd.org, FreeBSD Questions <freebsd-questions@freebsd.org>, Andrew Boyer <aboyer@averesystems.com> Subject: Re: Intel X520-DA2 Supported in stable/8? Message-ID: <CAFOYbcn4kx9=-2GQv08s9qJCk6%2B7nLMnkCKrAX4VDjq%2Bg8GePQ@mail.gmail.com> In-Reply-To: <CAHzLAVFqXYJew%2BEkygZJQx4jKEFqatJiXc781YDNtnmGb3R6tQ@mail.gmail.com> References: <CAHzLAVFpkfZGebZdwpxYwhX4Lr8_Cm%2BAeZc2LfQwL4NqbXZOwA@mail.gmail.com> <CAHzLAVEuwJOrhjvG-QJc0EH4cyKeFxJmfFHEe%2Bxutn8gKqTNJg@mail.gmail.com> <B841FA61-76EE-408C-8472-91DCF378CBFD@averesystems.com> <CAHzLAVH93ZVxaauS7Te_wHDvJuh0k=3TbopQj4jyFCycu7DXdA@mail.gmail.com> <CAHzLAVFqXYJew%2BEkygZJQx4jKEFqatJiXc781YDNtnmGb3R6tQ@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Increase your system mbuf pool size, you do not want that failure to happen. Jack On Fri, Jun 22, 2012 at 2:01 PM, Rick Miller <vmiller@hostileadmin.com>wrote: > dmesg and ifconfig output below... > > On Fri, Jun 22, 2012 at 4:02 PM, Rick Miller <vmiller@hostileadmin.com> > wrote: > > On Fri, Jun 22, 2012 at 3:54 PM, Andrew Boyer <aboyer@averesystems.com> > wrote: > >> The ixgbe driver creates devices named ix0, etc. > >> > >> I believe you need to run 'ifconfig ix0 up' before it will attempt to > get link. > > > > Thanks for clarifying that tidbit. At least I know the driver loading > > is the correct driver :) > > > > I did try ifup'ing the interface...it shows the interface up, status > > is still no carrier. I've had confirmation that the cable itself is > > good. I wonder if it matters that the upstream switch has VLAN > > tagging enabled? > > ix0: <Intel(R) PRO/10GbE PCI-Express Network Driver, Version - 2.4.5> > port 0x7000-0x701f mem 0xf6b80000-0xf6bfffff,0xf6b70000-0xf6b73fff irq > 40 at device 0.0 on pci7 > ix0: Using MSIX interrupts with 9 vectors > ix0: RX Descriptors exceed system mbuf max, using default instead! > ix0: [ITHREAD] > ix0: [ITHREAD] > ix0: [ITHREAD] > ix0: [ITHREAD] > ix0: [ITHREAD] > ix0: [ITHREAD] > ix0: [ITHREAD] > ix0: [ITHREAD] > ix0: [ITHREAD] > ix0: Ethernet address: 90:e2:ba:15:e2:60 > ix0: PCI Express Bus: Speed 5.0Gb/s Width x8 > ix1: <Intel(R) PRO/10GbE PCI-Express Network Driver, Version - 2.4.5> > port 0x7020-0x703f mem 0xf6a80000-0xf6afffff,0xf6a70000-0xf6a73fff irq > 44 at device 0.1 on pci7 > ix1: Using MSIX interrupts with 9 vectors > ix1: RX Descriptors exceed system mbuf max, using default instead! > ix1: [ITHREAD] > ix1: [ITHREAD] > ix1: [ITHREAD] > ix1: [ITHREAD] > ix1: [ITHREAD] > ix1: [ITHREAD] > ix1: [ITHREAD] > ix1: [ITHREAD] > ix1: [ITHREAD] > ix1: Ethernet address: 90:e2:ba:15:e2:61 > ix1: PCI Express Bus: Speed 5.0Gb/s Width x8 > > > ix0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > > options=401bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,VLAN_HWTSO> > ether 90:e2:ba:XX:XX:XX > inet 10.1.2.50 netmask 0xfffffe00 broadcast 10.1.3.255 > media: Ethernet autoselect > status: no carrier > ix1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 > > options=401bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,VLAN_HWTSO> > ether 90:e2:ba:XX:XX:XX > media: Ethernet autoselect > status: no carrier > > > -- > Take care > Rick Miller > _______________________________________________ > freebsd-stable@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-stable > To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org" >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CAFOYbcn4kx9=-2GQv08s9qJCk6%2B7nLMnkCKrAX4VDjq%2Bg8GePQ>