Date: Thu, 24 May 2001 11:53:38 -0600 (MDT) From: "Forrest W. Christian" <forrestc@imach.com> To: Jonathan Lemon <jlemon@flugsvamp.com> Cc: stable@FreeBSD.ORG Subject: Re: fxp0 "sleeping" Problem (NOT NEW DRIVER RELATED) Message-ID: <Pine.BSF.4.21.0105241148520.25599-100000@workhorse.iMach.com> In-Reply-To: <200105241727.f4OHRW994688@prism.flugsvamp.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Thu, 24 May 2001, Jonathan Lemon wrote:
> kern.debug /var/log/messages
Yep... It's in there:
*.notice;kern.debug;lpr.info;mail.crit;news.err /var/log/messages
I've also now added:
*.* /var/log/everything
Just in case it's logging somewhere else. It hasn't hung since I added
this :)
Requested outputs:
mail# dmesg
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.3-STABLE #4: Wed May 23 16:27:12 MDT 2001
root@mail.mt.net:/usr/src/sys/compile/MAIL
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (930.32-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,
MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory = 535560192 (523008K bytes)
avail memory = 518434816 (506284K bytes)
pnpbios: Bad PnP BIOS data checksum
Preloaded elf kernel "kernel" at 0xc02de000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82810E (i810E GMCH) Host To Hub bridge> on motherboard
pci0: <PCI bus> on pcib0
pci0: <Intel 82810E (i810E GMCH) SVGA controller> at 1.0 irq 11
pcib1: <Intel 82801AA (ICH) Hub to PCI bridge> at device 30.0 on pci0
pci1: <PCI bus> on pcib1
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xde80-0xdebf mem
0xff700000-0xff7fffff,0xff8fe000-0xff8fefff irq 9 at device 1.0 on pci1
fxp0: Ethernet address 00:d0:b7:aa:8d:22
pci1: <unknown card> (vendor=0x1274, dev=0x1371) at 7.0 irq 11
isab0: <Intel 82801AA (ICH) PCI to LPC bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH ATA66 controller> port 0xffa0-0xffaf at device 31.1 on
pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82801AA (ICH) USB controller> port 0xef80-0xef9f irq 9 at
device 31.2 on pci0
usb0: <Intel 82801AA (ICH) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <unknown card> (vendor=0x8086, dev=0x2413) at 31.3 irq 10
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
RTC BIOS diagnostic error 2
IP packet filtering initialized, divert disabled, rule-based forwarding
enabled, default to deny, logging disabled
ad0: 38166MB <WDC WD400BB-00AUA1> [77545/16/63] at ata0-master UDMA66
ad2: 38166MB <WDC WD400BB-00AUA1> [77545/16/63] at ata1-master UDMA66
Mounting root from ufs:/dev/ad0s1a
mail# ifconfig -a
fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 206.127.64.140 netmask 0xffffff00 broadcast 206.127.64.255
inet6 fe80::2d0:b7ff:feaa:8d22%fxp0 prefixlen 64 scopeid 0x1
ether 00:d0:b7:aa:8d:22
media: autoselect (100baseTX <full-duplex>) status: active
supported media: autoselect 100baseTX <full-duplex> 100baseTX
10baseT/UTP <full-duplex> 10baseT/UTP
lp0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
gif1: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
gif2: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
gif3: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x7
inet6 ::1 prefixlen 128
inet 127.0.0.1 netmask 0xff000000
faith0: flags=8000<MULTICAST> mtu 1500
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.21.0105241148520.25599-100000>