Date: Sat, 20 Feb 2021 00:14:36 +0000 From: bugzilla-noreply@freebsd.org To: bugs@FreeBSD.org Subject: [Bug 253708] Problem booting FreeBSD 12.2 on Dell R730xd unless using verbose boot Message-ID: <bug-253708-227@https.bugs.freebsd.org/bugzilla/>
next in thread | raw e-mail | index | archive | help
https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=3D253708 Bug ID: 253708 Summary: Problem booting FreeBSD 12.2 on Dell R730xd unless using verbose boot Product: Base System Version: 12.2-RELEASE Hardware: amd64 OS: Any Status: New Severity: Affects Some People Priority: --- Component: kern Assignee: bugs@FreeBSD.org Reporter: pen@lysator.liu.se There seems to be some timing-related problem when booting a Dell R730xd se= rver with FreeBSD 12.2. Possibly related to the Intel X710 10G ethernet cards, s= ince the freeze seems to be happening when it activates the second ixl port. It boots just fine with FreeBSD 11.3 If I hit 7 during the boot sequence and enable verbose boot then the system seems to boot just fine though.=20 Non-verbose serial port (via IPMI) boot output below. One interresting thin= g is that it seems to kill the IPMI session too when this happens (over a dedica= ted separate port): ixl3: Using MSI-X interrupts with 9 vectors ixl3: Ethernet address: 3c:fd:fe:0f:3c:c6 ixl3: Allocating 8 queues for PF LAN VSI; 8 queues active ixl3: PCI Express Bus: Speed 8.0GT/s Width x8 ixl3: Failed to initialize SR-IOV (error=3D2) ixl3: netmap queues/slots: TX 8/1024, RX 8/1024 pci2: <unknown> at device 17.0 (no driver attached) ahci0: <Intel Wellsburg AHCI SATA controller> port 0x3078-0x307f,0x308c-0x308f,0x3070-0x3077,0x3088-0x308b,0x3040-0x305f mem 0x97111000-0x971117ff at device 17.4 numa-domain 0 on pci2 ahci0: AHCI v1.30 with 4 6Gbps ports, Port Multiplier not supported ahcich0: <AHCI channel> at channel 0 on ahci0 ahcich1: <AHCI channel> at channel 1 on ahci0 ahciem0: <AHCI enclosure management bridge> on ahci0 xhci0: <Intel Wellsburg USB 3.0 controller> mem 0x97100000-0x9710ffff at de= vice 20.0 numa-domain 0 on pci2 xhci0: 32 bytes context size, 64-bit DMA ixl0: Link is up, 10 Gbps Full Duplex, Requested FEC: None, Negotiated FEC: None, Autoneg: False, Flow Control: None ixl0: link state changed to UP usbus0 numa-domain 0 on xhci0 usbus0: 5.0Gbps Super Speed USB v3.0 pci2: <simple comms> at device 22.0 (no driver attached) pci2: <simple comms> at device 22.1 (no driver attached) ehci0: <Intel Wellsburg USB 2.0 controller> mem 0x97113000-0x971133ff at de= vice 26.0 numa-domain 0 on pci2 usbus1: EHCI version 1.0 usbus1 numa-domain 0 on ehci0 usbus1: 480Mbps High Speed USB v2.0 pcib7: <PCI-PCI bridge> at device 28.0 numa-domain 0 on pci2 pci7: <PCI bus> numa-domain 0 on pcib7 pcib8: <ACPI PCI-PCI bridge> at device 28.7 numa-domain 0 on pci2 pci8: <ACPI PCI bus> numa-domain 0 on pcib8 pcib9: <PCI-PCI bridge> at device 0.0 numa-domain 0 on pci8 pci9: <PCI bus> numa-domain 0 on pcib9 pcib10: <PCI-PCI bridge> at device 0.0 numa-domain 0 on pci9 pci10: <PCI bus> numa-domain 0 on pcib10 ixl2: Link is upError: No response to keepalive - Terminating session ixl0 & ixl2 is set up as a lagg0 port in failover mode. --=20 You are receiving this mail because: You are the assignee for the bug.=
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?bug-253708-227>