Date: Wed, 25 Apr 2018 21:15:51 +0000 From: Paul Esson <paul.esson@redstor.com> To: "Rodney W. Grimes" <freebsd-rwg@pdx.rh.cn85.dnsmgr.net> Cc: Harry Schmalzbauer <freebsd@omnilan.de>, "freebsd-virtualization@freebsd.org" <freebsd-virtualization@freebsd.org> Subject: Re: bhyve networking Message-ID: <HE1PR0102MB2588F1B078AB3A5D89DD6D1A9E8F0@HE1PR0102MB2588.eurprd01.prod.exchangelabs.com> In-Reply-To: <201804252033.w3PKXv8M097827@pdx.rh.CN85.dnsmgr.net> References: <HE1PR0102MB25884F467EE8019D3D298E419E8F0@HE1PR0102MB2588.eurprd01.prod.exchangelabs.com>, <201804252033.w3PKXv8M097827@pdx.rh.CN85.dnsmgr.net>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi Rod,
Can you share a command line for that? I also tried presenting an access p=
ort from my switch on a specific VLAN - not trimmed. Would I still have to=
tag the interface on the guest in that scenario?
Regards,
Paul Esson | Redstor Limited
t +44 (0)118 951 5235
m +44 (0)776 690 6514
e paul.esson@redstor.com
________________________________
From: Rodney W. Grimes <freebsd-rwg@pdx.rh.CN85.dnsmgr.net>
Sent: Wednesday, April 25, 2018 9:33:57 PM
To: Paul Esson
Cc: Harry Schmalzbauer; freebsd-virtualization@freebsd.org
Subject: Re: bhyve networking
[ Charset windows-1252 unsupported, converting... ]
> Hi Harry,
> I?m simply using the ?vm? utility as in
>
> vm switch create public
> vm switch add public igb1
>
> That must make underlying calls to if config or equivalent as the bridge =
and tap interfaces are created automatically.
>
> The vm template file has these relevant parameters
>
> network0_type=3D?virtio-net?
> network0_switch=3D?public?
>
> I?ve done nothing to the igb1 interface other than connect it to a physic=
al switch on the appropriate VLAN.
How have you configured your vtnet devices inside the guest? If your pass =
a "trunked" ethernet device
to a guest the guest is going to need to run vlan decapuslation. I do this=
here, and it works fine.
vtnet0: flags=3D8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric=
0 mtu 1500
options=3D80028<VLAN_MTU,JUMBO_MTU,LINKSTATE>
ether 58:9c:fc:0e:8b:ec
nd6 options=3D29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet 10Gbase-T <full-duplex>
status: active
lo0: flags=3D8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=3D600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
nd6 options=3D21<PERFORMNUD,AUTO_LINKLOCAL>
groups: lo
vlan48: flags=3D8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1=
500
ether 58:9c:fc:0e:8b:ec
inet 192.168.48.38 netmask 0xffffff00 broadcast 192.168.48.255
nd6 options=3D29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet 10Gbase-T <full-duplex>
status: active
vlan: 48 vlanpcp: 0 parent interface: vtnet0
groups: vlan
...
>
> Bez?glich Paul Esson's Nachricht vom 25.04.2018 20:44 (localtime):
> > Hi Folks,
> >
> > I'm struggling with networking when using vm-bhyve on FreeBSD 11.1-RELE=
ASE. I have two NICs and have configured the first (igb0) on a management n=
etwork and want to use the second (igb1) for VMs. However, I can't get any=
VM to communicate through the virtual switch if I have igb1 added to it. =
If I take the NIC out of the switch and configure an ipv4 address on it I c=
an reach other hosts on the relevant subnet so I believe the poet set-up is=
valid. If I replace igb1 in the switch with igb0, I can then configure VM=
s on my management network and they have network connectivity. Can I only =
use
>
> Hello,
>
> a example of the command you used was nice.
> I guess you're using if_bridge(4) ? the example would clarify.
> But there's ng_bridge(4) and vale(4) also, and others are using
> OpenVSwitch...
>
> > an interface that has an IP address configured at the host level befor=
e adding it to the switch? I've used other
>
> No.
> But the interface has to be in promisc mode. And some offloading
> functions must be disabled, but in case of if_bridge(4), it's done
> automagically (and reverted if you remove the interface again).
>
> Hth,
>
> -harry
> _______________________________________________
> freebsd-virtualization@freebsd.org mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-virtualization
> To unsubscribe, send any mail to "freebsd-virtualization-unsubscribe@free=
bsd.org"
>
>
--
Rod Grimes rgrimes@freebsd.=
org
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?HE1PR0102MB2588F1B078AB3A5D89DD6D1A9E8F0>