Date: Tue, 11 Dec 2018 09:57:29 +0100 From: Ruben <mail@osfux.nl> To: freebsd-stable@freebsd.org Subject: Re: 11.2-STABLE and MMC problems on pcEngines apu2c0 Message-ID: <725ca086-02b0-528b-d2f8-b40673f3f494@osfux.nl> In-Reply-To: <13da0931-8dcc-27d1-cb7a-01de554a96b6@denninger.net> References: <13da0931-8dcc-27d1-cb7a-01de554a96b6@denninger.net>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi Karl, Did you try running the newest firmware on the apu2 ? You might want to give that a try. I ran into the same issue you appear to be running into and for me the newest firmware fixed it. Beware though: there are 2 kinds of firmware available for the APU(2) boards if I remember correctly. One is only compatible with the linuxes, the "legacy" branch should be used for running the bsds. You might want to check out this repo: https://pcengines.github.io/#lr-10 Kind regards, Ruben On 12/10/18 10:38 PM, Karl Denninger wrote: > Built this morning.... > > FreeBSD 11.2-STABLE #0 r341796: Mon Dec 10 13:20:13 CST 2018 > > System is a pcEngines machine, apu2c0. It has been running on > 11.0-STABLE for well north of a year without problems. It boots and > runs on 11.2, but I'm getting a LOT of these errors... > > mmc0: CMD7 failed, RESULT: 1 > mmc0: Card at relative address 43690 failed to select > mmc0: CMD7 failed, RESULT: 1 > mmc0: Card at relative address 43690 failed to select > mmc0: CMD7 failed, RESULT: 1 > mmc0: Card at relative address 43690 failed to select > mmc0: CMD7 failed, RESULT: 1 > mmc0: Card at relative address 43690 failed to select > mmc0: CMD7 failed, RESULT: 1 > mmc0: Card at relative address 43690 failed to select > mmc0: Card at relative address 43690 failed to select > mmc0: Card at relative address 43690 failed to select > mmc0: Card at relative address 43690 failed to select > mmc0: Card at relative address 43690 failed to select > mmc0: Card at relative address 43690 failed to select > mmc0: Card at relative address 43690 failed to select > mmc0: Card at relative address 43690 failed to select > > Same SD card, same everything EXCEPT that I booted partition 2 (for > 11.2) rather than partition 1 (11.0.) > > In both cases the root filesystem is mounted read-only (this is a > NanoBSD config) so there shouldn't be any write I/O going to the card at > all. As far as I can tell the errors going to the console aren't > preventing anything from starting and running, but they sure don't look > good! > > dmesg -a from 11.0 (by the time I can get to it on 11.2 the boot > messages are long-since scrolled off) > > Copyright (c) 1992-2017 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 11.0-STABLE #0 r312669M: Wed Jun 14 17:57:26 CDT 2017 > > root@NewFS.denninger.net:/pics/Crochet-work-AMD/obj/usr/src/sys/KSD-SMP > amd64 > FreeBSD clang version 3.9.1 (tags/RELEASE_391/final 289601) (based on > LLVM 3.9.1) > VT(vga): resolution 640x480 > CPU: AMD GX-412TC SOC (998.15-MHz > K8-class CPU) > Origin="AuthenticAMD" Id=0x730f01 Family=0x16 Model=0x30 Stepping=1 > > Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> > > Features2=0x3ed8220b<SSE3,PCLMULQDQ,MON,SSSE3,CX16,SSE4.1,SSE4.2,MOVBE,POPCNT,AESNI,XSAVE,OSXSAVE,AVX,F16C> > AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM> > AMD > Features2=0x1d4037ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT,Topology,PNXC,DBE,PTSC,PL2I> > Structured Extended Features=0x8<BMI1> > XSAVE Features=0x1<XSAVEOPT> > SVM: NP,NRIP,AFlush,DAssist,NAsids=8 > TSC: P-state invariant, performance statistics > real memory = 2012930048 (1919 MB) > avail memory = 1906143232 (1817 MB) > Event timer "LAPIC" quality 100 > ACPI APIC Table: <CORE COREBOOT> > FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs > FreeBSD/SMP: 1 package(s) x 4 core(s) > ioapic1: Changing APIC ID to 5 > ioapic0 <Version 2.1> irqs 0-23 on motherboard > ioapic1 <Version 2.1> irqs 24-55 on motherboard > random: entropy device external interface > kbd0 at kbdmux0 > netmap: loaded module > module_register_init: MOD_LOAD (vesa, 0xffffffff8101fd00, 0) error 19 > nexus0 > vtvga0: <VT VGA driver> on motherboard > cryptosoft0: <software crypto> on motherboard > acpi0: <CORE COREBOOT> on motherboard > acpi0: Power Button (fixed) > cpu0: <ACPI CPU> on acpi0 > cpu1: <ACPI CPU> on acpi0 > cpu2: <ACPI CPU> on acpi0 > cpu3: <ACPI CPU> on acpi0 > atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 > Event timer "RTC" frequency 32768 Hz quality 0 > attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0 > Timecounter "i8254" frequency 1193182 Hz quality 0 > Event timer "i8254" frequency 1193182 Hz quality 100 > Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 > acpi_timer0: <32-bit timer at 3.579545MHz> port 0x818-0x81b on acpi0 > hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 > Timecounter "HPET" frequency 14318180 Hz quality 950 > acpi_button0: <Power Button> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pcib1: <ACPI PCI-PCI bridge> at device 2.2 on pci0 > pcib1: failed to allocate initial I/O port window: 0x1000-0x1fff > pci1: <ACPI PCI bus> on pcib1 > igb0: <Intel(R) PRO/1000 Network Connection, Version - 2.5.3-k> mem > 0xfe700000-0xfe71ffff,0xfe720000-0xfe723fff at device 0.0 on pci1 > igb0: Using MSIX interrupts with 3 vectors > igb0: Ethernet address: 00:0d:b9:46:71:88 > igb0: Bound queue 0 to cpu 0 > igb0: Bound queue 1 to cpu 1 > igb0: netmap queues/slots: TX 2/1024, RX 2/1024 > pcib2: <ACPI PCI-PCI bridge> at device 2.4 on pci0 > pci2: <ACPI PCI bus> on pcib2 > igb1: <Intel(R) PRO/1000 Network Connection, Version - 2.5.3-k> port > 0x2000-0x201f mem 0xfe800000-0xfe81ffff,0xfe820000-0xfe823fff at device > 0.0 on pci2 > igb1: Using MSIX interrupts with 3 vectors > igb1: Ethernet address: 00:0d:b9:46:71:89 > igb1: Bound queue 0 to cpu 2 > igb1: Bound queue 1 to cpu 3 > igb1: netmap queues/slots: TX 2/1024, RX 2/1024 > pci0: <encrypt/decrypt> at device 8.0 (no driver attached) > xhci0: <AMD FCH USB 3.0 controller> mem 0xfeb22000-0xfeb23fff at device > 16.0 on pci0 > xhci0: 32 bytes context size, 64-bit DMA > xhci0: Unable to map MSI-X table > usbus0 on xhci0 > ahci0: <AMD Hudson-2 AHCI SATA controller> port > 0x3010-0x3017,0x3020-0x3023,0x3018-0x301f,0x3024-0x3027,0x3000-0x300f > mem 0xfeb25000-0xfeb253ff at device 17.0 on pci0 > ahci0: AHCI v1.30 with 2 6Gbps ports, Port Multiplier supported with FBS > ahcich0: <AHCI channel> at channel 0 on ahci0 > ahcich1: <AHCI channel> at channel 1 on ahci0 > ehci0: <AMD FCH USB 2.0 controller> mem 0xfeb25400-0xfeb254ff at device > 19.0 on pci0 > usbus1: EHCI version 1.0 > usbus1 on ehci0 > isab0: <PCI-ISA bridge> at device 20.3 on pci0 > isa0: <ISA bus> on isab0 > sdhci_pci0: <Generic SD HCI> mem 0xfeb25500-0xfeb255ff at device 20.7 on > pci0 > sdhci_pci0: 1 slot(s) allocated > mmc0: <MMC/SD bus> on sdhci_pci0 > amdtemp0: <AMD CPU On-Die Thermal Sensors> on hostb5 > uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 > uart0: console (115200,n,8,1) > orm0: <ISA Option ROMs> at iomem 0xc0000-0xc0fff,0xef000-0xeffff on isa0 > ppc0: cannot reserve I/O port range > uart1: <16550 or compatible> at port 0x2f8 irq 3 on isa0 > hwpstate0: <Cool`n'Quiet 2.0> on cpu0 > Timecounters tick every 1.000 msec > DUMMYNET 0 with IPv6 initialized (100409) > load_dn_sched dn_sched QFQ loaded > usbus0: 5.0Gbps Super Speed USB v3.0 > usbus1: 480Mbps High Speed USB v2.0 > load_dn_sched dn_sched RR loaded > load_dn_sched dn_sched WF2Q+ loaded > load_dn_sched dn_sched FIFO loaded > load_dn_sched dn_sched FQ_CODEL loaded > load_dn_sched dn_sched FQ_PIE loaded > load_dn_sched dn_sched PRIO loaded > load_dn_aqm dn_aqm CODEL loaded > load_dn_aqm dn_aqm PIE loaded > nvme cam probe device init > ugen0.1: <0x1022 XHCI root HUB> at usbus0 > uhub0: <0x1022 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0 > ugen1.1: <AMD EHCI root HUB> at usbus1 > uhub1: <AMD EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 > mmcsd0: 16GB <SDHC SL16G 8.0 SN A4981A22 MFG 01/2017 by 3 SD> at mmc0 > 31.5MHz/4bit/65535-block > SMP: AP CPU #1 Launched! > SMP: AP CPU #3 Launched! > SMP: AP CPU #2 Launched! > Timecounter "TSC" frequency 998148762 Hz quality 1000 > Trying to mount root from ufs:/dev/mmcsd0s1a [ro]... > uhub0: 4 ports with 4 removable, self powered > uhub1: 2 ports with 2 removable, self powered > ugen1.2: <vendor 0x0438 product 0x7900> at usbus1 > uhub2 on uhub1 > uhub2: <vendor 0x0438 product 0x7900, class 9/0, rev 2.00/0.18, addr 2> > on usbus1 > uhub2: 4 ports with 4 removable, self powered > random: unblocking device. > Setting hostuuid: 1295647e-51e2-11e7-a9c2-000db9467188. > Setting hostid: 0xa175f087. > Starting file system checks: > /dev/mmcsd0s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS > /dev/mmcsd0s1a: clean, 2091305 free (7889 frags, 260427 blocks, 0.2% > fragmentation) > /dev/mmcsd0s3: FILE SYSTEM CLEAN; SKIPPING CHECKS > /dev/mmcsd0s3: clean, 118711 free (31 frags, 14835 blocks, 0.0% > fragmentation) > /dev/mmcsd0s4: FILE SYSTEM CLEAN; SKIPPING CHECKS > /dev/mmcsd0s4: clean, 700000 free (920 frags, 87385 blocks, 0.1% > fragmentation) > Mounting local filesystems:. > ELF ldconfig path: /lib /usr/lib /usr/local/lib /usr/local/lib/ipsec > /usr/local/lib/perl5/5.24/mach/CORE > 32-bit compatibility ldconfig path: /usr/lib32 > Setting hostname: IpGw.Denninger.Net. > Additional TCP/IP options: IPv6 CPE WANIF=igb0. > Setting up harvesting: > [UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,NET_ETHER,NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED > Feeding entropy: eval: cannot create /boot/entropy: Read-only file system > Starting Network: lo0 igb0 igb1 enc0. > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 > options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6> > inet6 ::1 prefixlen 128 > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3 > inet 127.0.0.1 netmask 0xff000000 > nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> > groups: lo > igb0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > > options=6000bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,RXCSUM_IPV6,TXCSUM_IPV6> > ether 00:0d:b9:46:71:88 > inet6 fe80::20d:b9ff:fe46:7188%igb0 prefixlen 64 scopeid 0x1 > nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL> > media: Ethernet autoselect > status: no carrier > igb1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > > options=2000bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,RXCSUM_IPV6> > ether 00:0d:b9:46:71:89 > inet 192.168.10.200 netmask 0xffffff00 broadcast 192.168.10.255 > inet 192.168.2.200 netmask 0xffffff00 broadcast 192.168.2.255 > inet6 fe80::20d:b9ff:fe46:7189%igb1 prefixlen 64 scopeid 0x2 > nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> > media: Ethernet autoselect > status: no carrier > enc0: flags=0<> metric 0 mtu 1536 > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > groups: enc > Starting devd. > Starting Network: enc0. > enc0: flags=0<> metric 0 mtu 1536 > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > groups: enc > igb1: link state changed to UP > igb1.3: link state changed to UP > igb0: link state changed to UP > Starting dhclient. > DHCPDISCOVER on igb0 to 255.255.255.255 port 67 interval 7 > DHCPOFFER from 10.2.224.1 > DHCPREQUEST on igb0 to 255.255.255.255 port 67 > DHCPACK from 10.2.224.1 > bound to 68.1.57.197 -- renewal in 43200 seconds. > add host 127.0.0.1: gateway lo0 fib 0: route already in table > Additional inet routing options: gateway=YES. > add host ::1: gateway lo0 fib 0: route already in table > add net fe80::: gateway ::1 > add net ff02::: gateway ::1 > add net ::ffff:0.0.0.0: gateway ::1 > add net ::0.0.0.0: gateway ::1 > Additional inet6 routing options: gateway=YES. > ipfw2 (+ipv6) initialized, divert loadable, nat loadable, default to > deny, logging disabled > Firewall rules loaded. > Starting local_unbound. > [1544477459] unbound[782:0] warning: too many file descriptors > requested. The builtinmini-event cannot handle more than 1024. Config > for less fds or compile with libevent > [1544477459] unbound[782:0] warning: continuing with less udp ports: 948 > Waiting for nameserver to start... good > Starting dhcp6c. > Creating and/or trimming log files. > Starting syslogd. > Clearing /tmp (X related). > Starting strongSwan 5.5.3 IPsec [starter]... > no netkey IPsec stack detected > no KLIPS IPsec stack detected > no known IPsec stack detected, ignoring! > Starting local daemons:add net 192.168.2.0: gateway 192.168.10.100 fib > 0: route already in table > . > Updating motd:. > Mounting late filesystems:. > Starting ntpd. > Starting powerd. > Starting rtadvd. > Dec 10 15:31:01 IpGw ntpd[985]: leapsecond file > ('/var/db/ntpd.leap-seconds.list'): expired less than 558 days ago > Starting dhcpd. > Internet Systems Consortium DHCP Server 4.3.5 > Copyright 2004-2016 Internet Systems Consortium. > All rights reserved. > For info, please visit https://www.isc.org/software/dhcp/ > Config file: /usr/local/etc/dhcpd.conf > Database file: /var/db/dhcpd.leases > PID file: /var/run/dhcpd.pid > Wrote 0 deleted host decls to leases file. > Wrote 0 new dynamic host decls to leases file. > Wrote 0 leases to leases file. > Listening on BPF/igb1.3/00:0d:b9:46:71:89/192.168.4.0/24 > Sending on BPF/igb1.3/00:0d:b9:46:71:89/192.168.4.0/24 > Listening on BPF/igb1/00:0d:b9:46:71:89/two-on-cable > Sending on BPF/igb1/00:0d:b9:46:71:89/two-on-cable > Sending on Socket/fallback/fallback-net > Starting sshguard. > Starting snmpd. > cannot forward src fe80:2::396c:673e:9cf:ba21, dst > 2600:1402:16::17db:a212, nxt 6, rcvif igb1, outif igb0 > Starting openvpn. > tun0: link state changed to UP > Configuring vt: blanktime. > Performing sanity check on sshd configuration. > Starting sshd. > Starting sendmail_submit. > Starting sendmail_msp_queue. > Starting cron. > Starting background file system checks in 60 seconds. > > Mon Dec 10 15:31:06 CST 2018 > cannot forward src fe80:2::396c:673e:9cf:ba21, dst > 2600:1402:16::17db:a212, nxt 6, rcvif igb1, outif igb0 > cannot forward src fe80:2::396c:673e:9cf:ba21, dst > 2600:1402:16::17db:a212, nxt 6, rcvif igb1, outif igb0 > cannot forward src fe80:2::396c:673e:9cf:ba21, dst > 2600:1402:16::17db:a212, nxt 6, rcvif igb1, outif igb0 > cannot forward src fe80:2::396c:673e:9cf:ba21, dst > 2600:1402:16::17db:a212, nxt 6, rcvif igb1, outif igb0 >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?725ca086-02b0-528b-d2f8-b40673f3f494>