Date: Mon, 21 Aug 2006 17:09:49 +0800 From: "Senandung Mendonan" <mendonan@gmail.com> To: freebsd-net@freebsd.org Subject: Re: Problem with IBM NetXtreme 1000-T GigaEthernet Adapter Message-ID: <94c7120b0608210209o482fef7ev1b4922d0597af666@mail.gmail.com> In-Reply-To: <09BFF2FA5EAB4A45B6655E151BBDD90301D42713@NT-IRVA-0750.brcm.ad.broadcom.com> References: <94c7120b0608181236j2475301ds1379510f94b12d34@mail.gmail.com> <09BFF2FA5EAB4A45B6655E151BBDD90301D42713@NT-IRVA-0750.brcm.ad.broadcom.com>
next in thread | previous in thread | raw e-mail | index | archive | help
David, On 8/19/06, David Christensen <davidch@broadcom.com> wrote: > > > I tried to use a FE version of the switch (Cisco Catalyst > > C3750), and a > > single-port version of the said NIC, with the same results > > (auto detect > > fails, and can only live with intermittent forced 100baseTX > > full-duplex). > > There isn't a single port version of the 5704, it must be a different > controller (maybe the 5703?). Which one is it exactly? You are right: the single-port version is actually the 5703. Here's the dmesg output for this particular one:- pci5: <ACPI PCI bus> on pcib4 bge0: <Broadcom BCM5703X Gigabit Ethernet, ASIC rev. 0x1100> mem 0xdcff0000-0xdc ffffff irq 48 at device 1.0 on pci5 miibus0: <MII bus> on bge0 brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX -FDX, auto bge0: Ethernet address: 00:10:18:16:43:d6 > Do either the > LOM devices or the add-in boards support remote management (such as > Serial-over-LAN or IPMI)? If so does disabling the feature change the > problem? No idea on this one. Where do I usually disable this -- in the BIOS I presume? > If you could attach a dump of dmesg that shows the messages from the > driver that might help too. Here's the dmesg for the dual-port version:- pci5: <ACPI PCI bus> on pcib4 bge0: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2100> mem 0xdcff0000-0xdcffffff irq 48 at device 1.0 on pci5 miibus0: <MII bus> on bge0 brgphy0: <BCM5704 10/100/1000baseTX PHY> on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto bge0: Ethernet address: 00:10:18:11:2a:0d bge1: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2100> mem 0xdcfe0000-0xdcfeffff irq 49 at device 1.1 on pci5 miibus1: <MII bus> on bge1 brgphy1: <BCM5704 10/100/1000baseTX PHY> on miibus1 brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto bge1: Ethernet address: 00:10:18:11:2a:0a Thanks. > > > --mendonan > > "Yang mimpikan secangkir kopi panas dengan selimut.." > > (Dreaming of a cup of hot coffee, and a blanket..") > > _______________________________________________ > > freebsd-net@freebsd.org mailing list > > http://lists.freebsd.org/mailman/listinfo/freebsd-net > > To unsubscribe, send any mail to "freebsd-net-unsubscribe@freebsd.org" > > > > > > -- --mendonan "Yang mimpikan secangkir kopi panas dengan selimut.." (Dreaming of a cup of hot coffee, and a blanket..")
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?94c7120b0608210209o482fef7ev1b4922d0597af666>