Date: Mon, 11 Nov 2002 20:41:07 -0800 From: "Greg Smith" <freebsd_mail@myrealbox.com> To: freebsd-mobile@freebsd.org Subject: Re: AcerNote 370P (373) Message-ID: <200211112041070606.C68D1847@smtp.myrealbox.com> In-Reply-To: <003401c289fe$1aa7fab0$641ea8c0@otidan> References: <00ed01c28769$46a7c0b0$3d07000a@jhermansxp> <20021109.220005.44519003.imp@bsdimp.com> <003401c289fe$1aa7fab0$641ea8c0@otidan>
next in thread | previous in thread | raw e-mail | index | archive | help
Jamie,
>pcic0: <Cirrus logic 6722> at port 0x3e0 iomem 0xd0000 on isa0
>pcic0: Polling mode
>pccard0: <PC Card bus (classic)> on pcic0
>pccard1: <PC Card bus (classic)> on pcic0
Can you boot this machine up under Windows? Machines with CL 6729/30
often require a non-standard port (e.g. 0xfcec or 0xfcfc, depends on
the motherboard I guess). The 6722 might also. Windows is smarter
about dealing with this, and can point you at the right port.
If that is the problem you will need to recompile your kernel or else
update kernel.conf.
HTH,
Greg
-----Original Message-----
>> : I have an AcerNote 370P (373 version) that does not want to play
>> : nice with PCMCIA cards. It locks up the screen and keyboard about
>> : 3 seconds after inserting a card (right after the beep). Once I
>> : eject the card, everything plays catch-up on screen.
>>
>> OK. Sounds like we're getting stuck asserting an interrupt during
>> the card's configuration. Sounds like it is pretty generic. What
>> version?
>
>Xircom CE-10/A
>USR Sportster 28.8/FAX
>3COM EtherLink III 3C589D-TP
>
>Doesn't seem to matter what I put in the slot - or which of the two
>slots I put the card in.
>
>> : I've tried leaving only a single IRQ in pccard.conf, reboot,
lockup
>> : again, try the next IRQ ... rinse, repeat. No luck.
>> :
>> : Anything to try next?
>>
>> Are you trying PCI interrupts or ISA interrupts?
hw.pcic.intr_path=1
>> is for pci interrupts, =2 for ISA interrupts. You might try both of
>> these.
>
># sysctl hw.pcic.intr_path
>hw.pcic.intr_path: 2
>
>Changed it to 1 in /boot/loader.conf, no difference.
>
>> What kind of PCIC bridge do you have in your machine?
>
>pcic0: <Cirrus logic 6722> at port 0x3e0 iomem 0xd0000 on isa0
>pcic0: Polling mode
>pccard0: <PC Card bus (classic)> on pcic0
>pccard1: <PC Card bus (classic)> on pcic0
>
>123456789012345678901234567890123456789012345678901234567890123456789
>
>Here's my verbose `dmesg` (I was determined and hooked up a serial
>cable to capture this) ... at the end, you'll see the messages during
>insert/remove of the (any) pccard.
>
>-- Jamie
>
>Hit [Enter] to boot immediately, or any other key for command prompt.
>
>Type '?' for a list of commands, 'help' for more detailed help.
>ok boot -v
>SMAP type=01 base=00000000 00000000 len=00000000 0009fc00
>SMAP type=02 base=00000000 0009fc00 len=00000000 00000400
>SMAP type=02 base=00000000 000e0000 len=00000000 00020000
>SMAP type=01 base=00000000 00100000 len=00000000 03f00000
>Copyright (c) 1992-2002 The FreeBSD Project.
>Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993,
1994
> The Regents of the University of California. All rights reserved.
>FreeBSD 4.6.2-RELEASE #0: Wed Aug 14 21:23:26 GMT 2002
> murray@builder.freebsdmall.com:/usr/src/sys/compile/GENERIC
>Calibrating clock(s) ... TSC clock: 132633341 Hz, i8254 clock: 1193198
Hz
>CLK_USE_I8254_CALIBRATION not specified - using default frequency
>Timecounter "i8254" frequency 1193182 Hz
>CLK_USE_TSC_CALIBRATION not specified - using old calibration method
>CPU: Pentium/P54C (132.63-MHz 586-class CPU)
> Origin = "GenuineIntel" Id = 0x52c Stepping = 12
> Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
>real memory = 67108864 (65536K bytes)
>Physical memory chunk(s):
>0x00001000 - 0x0009efff, 647168 bytes (158 pages)
>0x004f7000 - 0x03ff7fff, 61870080 bytes (15105 pages)
>avail memory = 60440576 (59024K bytes)
>bios32: Found BIOS32 Service Directory header at 0xc00f0280
>bios32: Entry = 0xf0210 (c00f0210) Rev = 0 Len = 1
>pcibios: PCI BIOS entry at 0x0
>pnpbios: Found PnP BIOS data at 0xc00f5460
>pnpbios: Entry = f2400:0 Rev = 1.0
>Other BIOS signatures found:
>ACPI: 00000000
>Preloaded elf kernel "kernel" at 0xc04d0000.
>Intel Pentium detected, installing workaround for F00F bug
>md0: Malloc disk
>Creating DISK md0
>Math emulator present
>pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
>pci_open(1a): mode1res=0x80000000 (0x80000000)
>pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=152110b9)
>pcibios: No call entry point
>npx0: <math processor> on motherboard
>npx0: INT 16 interface
>i586_bzero() bandwidth = 125928724 bytes/sec
>bzero() bandwidth = 190730497 bytes/sec
>pcib0: <Host to PCI bridge> on motherboard
>found-> vendor=0x10b9, dev=0x1521, revid=0x1c
> class=06-00-00, hdrtype=0x00, mfdev=0
> subordinatebus=0 secondarybus=0
>found-> vendor=0x10b9, dev=0x1523, revid=0x07
> class=06-01-00, hdrtype=0x00, mfdev=1
> subordinatebus=0 secondarybus=0
>found-> vendor=0x10b9, dev=0x5219, revid=0x20
> class=01-01-fa, hdrtype=0x00, mfdev=1
> subordinatebus=0 secondarybus=0
> intpin=a, irq=0
> map[20]: type 1, range 32, base 0000f000, size 4
>found-> vendor=0x102c, dev=0x00e0, revid=0x45
> class=03-00-00, hdrtype=0x00, mfdev=0
> subordinatebus=0 secondarybus=0
> map[10]: type 1, range 32, base ff000000, size 24
>pci0: <PCI bus> on pcib0
>isab0: <PCI to ISA bridge (vendor=10b9 device=1523)> at device 2.0 on
pci0
>isa0: <ISA bus> on isab0
>atapci0: <Generic PCI ATA controller> port 0xf000-0xf00f irq 0 at
device
>2.1 on pci0
>atapci0: Busmastering DMA not supported
>ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x0000
>ata0: mask=03 ostat0=50 ostat2=00
>ata0-master: ATAPI 00 00
>ata0-slave: ATAPI 00 00
>ata0: mask=03 stat0=50 stat1=00
>ata0-master: ATA 01 a5
>ata0: devices=01
>ata0: at 0x1f0 irq 14 on atapci0
>ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x0000
>ata1: mask=01 ostat0=51 ostat2=ff
>ata1-master: ATAPI 14 eb
>ata1: mask=01 stat0=00 stat1=00
>ata1: devices=04
>ata1: at 0x170 irq 15 on atapci0
>pci0: <Chips & Technologies 65550 SVGA controller> (vendor=0x102c,
>dev=0x00e0) at 6.0
>ex_isa_identify()
>ata-: ata0 exists, using next available unit number
>ata-: ata1 exists, using next available unit number
>Trying Read_Port at 203
>Trying Read_Port at 243
>Trying Read_Port at 283
>Trying Read_Port at 2c3
>Trying Read_Port at 303
>Trying Read_Port at 343
>Trying Read_Port at 383
>Trying Read_Port at 3c3
>isa_probe_children: disabling PnP devices
>isa_probe_children: probing non-PnP devices
>orm0: <Option ROM> at iomem 0xc0000-0xcafff on isa0
>fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
isa0
>fdc0: FIFO enabled, 8 bytes threshold
>fd0: <1440-KB 3.5" drive> on fdc0 drive 0
>ata2 failed to probe at port 0x1f0 irq 14 on isa0
>ata3 failed to probe at port 0x170 irq 15 on isa0
>adv0 failed to probe on isa0
>bt0: Failed Status Reg Test - ff
>bt_isa_probe: Probe failed at 0x330
>bt0: Failed Status Reg Test - ff
>bt_isa_probe: Probe failed at 0x334
>bt0: Failed Status Reg Test - ff
>bt_isa_probe: Probe failed at 0x230
>bt0: Failed Status Reg Test - ff
>bt_isa_probe: Probe failed at 0x234
>bt0: Failed Status Reg Test - ff
>bt_isa_probe: Probe failed at 0x130
>bt0: Failed Status Reg Test - ff
>bt_isa_probe: Probe failed at 0x134
>bt0 failed to probe at port 0x134-0x137 on isa0
>aha0: status reg test failed ff
>aha0: status reg test failed ff
>aha0: status reg test failed ff
>aha0: status reg test failed ff
>aha0: status reg test failed ff
>aha0: status reg test failed ff
>aha0 failed to probe at port 0x134-0x137 on isa0
>aic0 failed to probe at port 0x140-0x15f on isa0
>atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
>atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
>atkbd: the current kbd controller command byte 0045
>atkbd: keyboard ID 0x54ab (2)
>kbdc: RESET_KBD return code:00fa
>kbdc: RESET_KBD status:00aa
>kbd0 at atkbd0
>kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
>psm0: current command byte:0045
>kbdc: TEST_AUX_PORT status:0000
>kbdc: RESET_AUX return code:00fa
>kbdc: RESET_AUX status:00aa
>kbdc: RESET_AUX ID:0000
>psm: status 00 02 64
>psm: status 00 00 64
>psm: status 00 03 64
>psm: status 00 03 64
>psm: data 08 00 00
>psm: status 10 00 64
>psm: status 00 02 64
>psm: data 08 00 00
>psm: status 00 02 64
>psm0: <PS/2 Mouse> irq 12 on atkbdc0
>psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
>psm0: config:00000000, flags:00000000, packet size:3
>psm0: syncmask:c0, syncbits:00
>vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
>fb0: vga0, vga, type:VGA (5), flags:0x7007f
>fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
>fb0: init mode:24, bios mode:3, current mode:24
>fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
>VGA parameters upon power-up
>50 18 10 00 00 01 03 00 02 67 5f 4f 50 82 55 81
>bf 1f 00 4f 0d 0e 00 00 03 20 9c 0e 8f 28 1f 96
>b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
>3d 3e 3f 0c 00 0f 00 00 00 00 00 00 10 0e 00 ff
>VGA parameters in BIOS for mode 24
>50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
>bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
>b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
>3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
>EGA/VGA parameters to be used for mode 24
>50 18 10 00 00 01 03 00 02 67 5f 4f 50 82 55 81
>bf 1f 00 4f 0d 0e 00 00 03 20 9c 0e 8f 28 1f 96
>b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
>3d 3e 3f 0c 00 0f 00 00 00 00 00 00 10 0e 00 ff
>sc0: <System console> at flags 0x100 on isa0
>sc0: VGA <16 virtual consoles, flags=0x100>
>sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
>pcic0: <Cirrus logic 6722> at port 0x3e0 iomem 0xd0000 on isa0
>pcic0: Polling mode
>pccard0: <PC Card bus (classic)> on pcic0
>pccard1: <PC Card bus (classic)> on pcic0
>pcic1: not probed (disabled)
>sio0: irq maps: 0x41 0x51 0x41 0x41
>sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
>sio0: type 16550A, console
>sio1: configured irq 3 not in bitmap of probed irqs 0
>sio1: irq maps: 0x41 0x41 0x41 0x41
>sio1: probe failed test(s): 0 1 2 4 6 7 9
>sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
>sio2: not probed (disabled)
>sio3: not probed (disabled)
>ppc0: parallel port found at 0x378
>ppc0: using extended I/O port range
>ppc0: EPP SPP
>ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
>ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
>plip0: <PLIP network interface> on ppbus0
>bpf: lp0 attached
>lpt0: <Printer> on ppbus0
>lpt0: Interrupt-driven port
>ppi0: <Parallel I/O> on ppbus0
>ed0 failed to probe at port 0x280-0x29f iomem 0xd8000 irq 10 on isa0
>fe0 failed to probe at port 0x300-0x31f on isa0
>ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
>lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0
>cs0 failed to probe at port 0x300-0x31f on isa0
>sn0 failed to probe at port 0x300-0x30f irq 10 on isa0
>isa_probe_children: probing PnP devices
>BIOS Geometries:
> 0:028c3f3f 0..652=653 cylinders, 0..63=64 heads, 1..63=63 sectors
> 1:03feff00 0..1022=1023 cylinders, 0..255=256 heads, 1..0=0 sectors
> 4:01eef511 0..494=495 cylinders, 0..245=246 heads, 1..17=17 sectors
> 5:016e7511 0..366=367 cylinders, 0..117=118 heads, 1..17=17 sectors
> 6:03feff00 0..1022=1023 cylinders, 0..255=256 heads, 1..0=0 sectors
> 7:03feff00 0..1022=1023 cylinders, 0..255=256 heads, 1..0=0 sectors
> 0 accounted for
>Device configuration finished.
>bpf: lo0 attached
>bpf: ppp0 attached
>new masks: bio 68c040, tty 631092, net 671092
>bpf: sl0 attached
>bpf: faith0 attached
>Creating DISK ad0
>ar: FreeBSD check1 failed
>ad0: <ST91350AG/06.06.02> ATA-3 disk at ata0-master
>ad0: 1287MB (2636928 sectors), 2616 C, 16 H, 63 S, 512 B
>ad0: 16 secs/int, 1 depth queue, BIOSPIO
>ad0: piomode=4 dmamode=2 udmamode=-1 cblid=0
>ata1-master: piomode=3 dmamode=-1 udmamode=-1 dmaflag=0
>acd0: <UJDCD8730/1.14> CDROM drive at ata1 as master
>acd0: read 1377KB/s (32754KB/s), 128KB buffer, BIOSPIO
>acd0: Reads: CD-DA
>acd0: Writes:
>acd0: Audio: play, 16 volume levels
>acd0: Mechanism: tray
>acd0: Medium: no/blank disc
>Mounting root from ufs:/dev/ad0s1a
>ad0s1: type 0xa5, start 0, end = 2636927, size 2636928
>ad0s1: C/H/S end 164/35/63 (374219) != end 2636927: invalid
>start_init: trying /sbin/init
>swapon: adding /dev/ad0s1b as swap device
>Automatic boot in progress...
>/dev/ad0s1a: FILESYSTEM CLEAN; SKIPPING CHECKS
>/dev/ad0s1a: clean, 47809 free (497 frags, 5914 blocks, 0.8%
fragmentation)
>/dev/ad0s1e: FILESYSTEM CLEAN; SKIPPING CHECKS
>/dev/ad0s1e: clean, 372955 free (8323 frags, 45579 blocks, 1.6%
>fragmentation)
>Setup PC-CARD: memory beep pccardd.
>Doing initial network setup:
> hostname.
>lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
> inet6 ::1 prefixlen 128
> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
> inet 127.0.0.1 netmask 0xff000000
>Additional routing options: TCP keepalive=YES.
>Routing daemons:.
>Additional daemons: syslogd.
>Doing additional network setup:.
>Starting final network daemons:.
>ELF ldconfig path: /usr/lib /usr/lib/compat
>a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout
>Starting standard daemons: inetd cron sshd sendmail
sendmail-clientmqueue.
>Initial rc.i386 initialization:.
>Configuring syscons: blanktime.
>Additional ABI support:.
>Local package initialization:.
>Additional TCP options:.
>
>Mon Nov 11 20:22:12 MST 2002
>
>FreeBSD/i386 (Amnesiac) (ttyd0)
>
>login: root
>
>Last login: Mon Nov 11 20:20:47 on ttyd0
>Nov 11 20:22:21 login: ROOT LOGIN (root) ON ttyd0
>
>Copyright (c) 1980, 1983, 1986, 1988, 1990, 1991, 1993, 1994
> The Regents of the University of California. All rights
reserved.
>
>FreeBSD 4.6.2-RELEASE (GENERIC) #0: Wed Aug 14 21:23:26 GMT 2002
>
>Welcome to FreeBSD!
>
># pcic0: Autodetected 3.3V card
>pccard: card inserted, slot 0
>pcic0: reset 1 int is 0 stat is cc
>pcic0: reset 2 int is 60 stat is cc
>pcic0: reset 3 int is 60 stat is cc
>Nov 11 20:22:32 pccardd[44]: No card in database for
"(null)"("(null)")
>pccard: card removed, slot 0
>
># tail -8 /var/log/messages
>Nov 11 20:22:21 login: ROOT LOGIN (root) ON ttyd0
>Nov 11 20:22:26 /kernel: pcic0: Autodetected 3.3V card
>Nov 11 20:22:26 /kernel: pccard: card inserted, slot 0
>Nov 11 20:22:26 /kernel: pcic0: reset 1 int is 0 stat is cc
>Nov 11 20:22:27 /kernel: pcic0: reset 2 int is 60 stat is cc
>Nov 11 20:22:27 /kernel: pcic0: reset 3 int is 60 stat is cc
>Nov 11 20:22:32 pccardd[44]: No card in database for
"(null)"("(null)")
>Nov 11 20:22:32 /kernel: pccard: card removed, slot 0
># exit
>
>
>To Unsubscribe: send mail to majordomo@FreeBSD.org
>with "unsubscribe freebsd-mobile" in the body of the message
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200211112041070606.C68D1847>