Date: Wed, 2 Apr 2003 19:07:01 +0200 From: Jukka Simila <home@jukkis.net> To: freebsd-multimedia@freebsd.org Subject: problem with tv + dga Message-ID: <200304021907.01772.home@jukkis.net>
next in thread | raw e-mail | index | archive | help
Hi. I recently updated my mobo/cpu/mem from Abit ZM6/Celeron 366@550/256 to Abit KD7/Athlon XP2100+ TB B/512 DDR333. After plugging everything in and rebooting, my tvcard hasn't worked properly. (tvcard is hauppauge wintv primio) problem is best described with a picture, ie. screenshot in http://www.jukkis.net/snapshot3.png IOW, only left side of image is rendered and only half of the lines. problem occurs when image is resized to max, there is some problems also with a little smaller image. however, fxtv -disableDirectV works properly, but is just way too slow. Any pointers what to change in BIOS or is there something to check in OS ? I'm assuming this is a HW issue.. I already tried to load failsafe defaults in bios, and restrict my Geforce2 MX to AGP 2x mode, but that doesn't change anything. I'm using NVidia's drivers, but also tried the nv driver from XFree86, same problem on both. I had 5.0-Release when I updated my pc, since then I updated to -p6 which hasn't helped. please cc any eventual replies, I'm unfortunately not on the list (for some reason subscribing didn't work, I tried several times when majordomo was in use, maybe I should try again now..) And dmesg follows: (notice the 'bktr' errors in the end of dmesg, maybe they are related) Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.0-RELEASE-p6 #3: Sun Mar 23 23:50:24 CET 2003 sjuke@sjukebox:/usr/RELENG_5_0/obj/usr/RELENG_5_0/src/sys/ATHLONXP Preloaded elf kernel "/boot/kernel/kernel" at 0xc05f4000. Preloaded userconfig_script "/boot/kernel.conf" at 0xc05f40a8. Preloaded elf module "/boot/kernel/nvidia.ko" at 0xc05f40f8. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc05f41a4. Timecounter "i8254" frequency 1193182 Hz CPU: AMD Athlon(tm) XP 2100+ (1734.07-MHz 686-class CPU) Origin = "AuthenticAMD" Id = 0x681 Stepping = 1 Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CM OV,PAT,PSE36,MMX,FXSR,SSE> AMD Features=0xffffffffc0400000<AMIE,DSP,3DNow!> real memory = 536805376 (511 MB) avail memory = 515055616 (491 MB) Initializing GEOMetry subsystem Pentium Pro MTRR support enabled npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: Other PM system enabled. Using $PIR table, 11 entries at 0xc00fdea0 apm0: <APM BIOS> on motherboard apm0: found APM BIOS v1.2, connected at v1.2 pcib0: <Host to PCI bridge> at pcibus 0 on motherboard pci0: <PCI bus> on pcib0 agp0: <VIA Generic host to PCI bridge> mem 0xe8000000-0xebffffff at device 0.0 o n pci0 pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 nvidia0: <GeForce2 MX/MX 400> mem 0xe0000000-0xe7ffffff,0xec000000-0xecffffff ir q 11 at device 0.0 on pci1 atapci0: <HighPoint HPT370 ATA100 controller> port 0xa000-0xa0ff,0x9c00-0x9c03,0 x9800-0x9807,0x9400-0x9403,0x9000-0x9007 irq 10 at device 9.0 on pci0 ata2: at 0x9000 on atapci0 ata3: at 0x9800 on atapci0 bktr0: <BrookTree 878> mem 0xee020000-0xee020fff irq 7 at device 11.0 on pci0 bktr0: Hauppauge Model 61294 D129 bktr0: Hauppauge WinCast/TV, Philips PAL I tuner, remote control. pci0: <multimedia> at device 11.1 (no driver attached) pcm0: <Creative EMU10K1> port 0xa400-0xa41f irq 3 at device 12.0 on pci0 uhci0: <VIA 83C572 USB controller> port 0xac00-0xac1f irq 11 at device 16.0 on pci0 usb0: <VIA 83C572 USB controller> on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered ugen0: Mustek Systems product 0xc420, rev 1.00/1.00, addr 2 uhci1: <VIA 83C572 USB controller> port 0xb000-0xb01f irq 10 at device 16.1 on pci0 usb1: <VIA 83C572 USB controller> on uhci1 usb1: USB revision 1.0 uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2: <VIA 83C572 USB controller> port 0xb400-0xb41f irq 3 at device 16.2 on pci0 usb2: <VIA 83C572 USB controller> on uhci2 usb2: USB revision 1.0 uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered pci0: <serial bus, USB> at device 16.3 (no driver attached) isab0: <PCI-ISA bridge> at device 17.0 on pci0 isa0: <ISA bus> on isab0 atapci1: <VIA 8235 ATA133 controller> port 0xb800-0xb80f at device 17.1 on pci0 ata0: at 0x1f0 irq 14 on atapci1 ata1: at 0x170 irq 15 on atapci1 pcm1: <VIA VT8235> port 0xbc00-0xbcff irq 3 at device 17.5 on pci0 vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xc000-0xc0ff mem 0xee023000-0xee02 30ff irq 11 at device 18.0 on pci0 vr0: Ethernet address: 00:50:8d:47:46:14 miibus0: <MII bus> on vr0 ukphy0: <Generic IEEE 802.3u media interface> on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto pmtimer0 on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model IntelliMouse, device ID 3 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 unknown: <PNP0303> can't assign resources (port) unknown: <PNP0f13> can't assign resources (irq) Timecounters tick every 10.000 msec ad0: 29198MB <SAMSUNG SV3063H> [59323/16/63] at ata0-master UDMA100 ar0: 152638MB <ATA RAID0 array> [19458/255/63] status: READY subdisks: 0 READY ad4: 76319MB <WDC WD800JB-00CRA1> [155061/16/63] at ata2-master UDMA100 1 READY ad6: 76319MB <WDC WD800JB-00CRA1> [155061/16/63] at ata3-master UDMA100 Opened disk ad4 -> 16 Opened disk ad4 -> 16 Opened disk ad6 -> 16 Opened disk ad6 -> 16 Mounting root from ufs:/dev/ar0s1a cd0 at ata1 bus 0 target 0 lun 0 cd0: <LITE-ON LTR-24102B 5S57> Removable CD-ROM SCSI-0 device cd0: 16.000MB/s transfers cd0: Attempt to query device size failed: NOT READY, Medium not present bktr0: ioctl: 439: rows too large or not even. bktr0: ioctl: 483: rows too large or not even. bktr0: ioctl: 595: columns too large or not even. bktr0: ioctl: 441: rows too large or not even. bktr0: ioctl: 617: columns too large or not even. bktr0: ioctl: 467: rows too large or not even. bktr0: ioctl: 487: rows too large or not even. uname -a: FreeBSD sjukebox 5.0-RELEASE-p6 FreeBSD 5.0-RELEASE-p6 #3: Sun Mar 23 23:50:24 CET 2003 sjuke@sjukebox:/usr/RELENG_5_0/obj/usr/RELENG_5_0/src/sys/ATHLONXP i386
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200304021907.01772.home>