Date: Mon, 25 Nov 2002 10:59:14 +0000 From: Paul <pao@ukc.ac.uk> To: freebsd-stable@freebsd.org Subject: ThinkPad R31 - Lucent windmodem woes.... Message-ID: <20021125105914.B240@luthien.ukc.ac.uk>
next in thread | raw e-mail | index | archive | help
Hi,
I have an R31 Thinkpad that has a Lucent Winmodem,
and am having trouble getting the thing to work under FreeBSD.
I have installed the comms/ltmdm port, this fails to
work (the kernel module is loaded) but pciconf doesn't report
the hardware device.
A rummage round the net, revealed that I should turn off PNP
in the BIOS - thats not an option on the R31.
So I tried the following in my kernel config:
options PCI_ENABLE_IO_MODES
as suggested by the driver developer (I forget the name), at the
moment the only error I get when I start ppp is:
luthien# ppp
Working in interactive mode
Using interface: tun0
ppp ON luthien> dial isp
Warning: deflink: /dev/cual0: Bad file descriptor
ppp ON luthien>
However the file is there:
luthien# ls -la /dev/cual0
crw-rw---- 1 uucp dialer 228, 128 Nov 25 10:29 /dev/cual0
kldstat reveals:
luthien# kldstat
Id Refs Address Size Name
1 6 0xc0100000 20bff4 kernel
3 1 0xc121a000 a000 ntfs.ko
4 1 0xc12bf000 1b000 usb.ko
5 1 0xc12f8000 3000 daemon_saver.ko
6 1 0xc12fb000 14000 linux.ko
7 1 0xc1342000 7d000 ltmdm.ko
Copies of pciconf -lv and dmesg follows, if anyone has any suggestions
other than using an external/pcmcia modem I would be very gratefull.
Thanks for your time.
Paul
-------------
pciconf -lv
============
chip0@pci0:0:0: class=0x060000 card=0x10171014 chip=0x35758086 rev=0x04 hdr=0x00
vendor = 'Intel Corporation'
device = '82830[MP] Host-Hub I/F Bridge / SDRAM Controller'
class = bridge
subclass = HOST-PCI
agp0@pci0:2:0: class=0x030000 card=0x05051014 chip=0x35778086 rev=0x04 hdr=0x00
vendor = 'Intel Corporation'
device = '82830M/MG Integrated Graphics Device'
class = display
subclass = VGA
none0@pci0:2:1: class=0x038000 card=0x05051014 chip=0x35778086 rev=0x00 hdr=0x00
vendor = 'Intel Corporation'
device = '82830M/MG Integrated Graphics Device'
class = display
uhci0@pci0:29:0: class=0x0c0300 card=0x10171014 chip=0x24828086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801CA/CAM (ICH3-S/ICH3-M) USB Controller #1'
class = serial bus
subclass = USB
uhci1@pci0:29:1: class=0x0c0300 card=0x10171014 chip=0x24848086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801CA/CAM (ICH3-S/ICH3-M) USB Controller #2'
class = serial bus
subclass = USB
uhci2@pci0:29:2: class=0x0c0300 card=0x10171014 chip=0x24878086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801CA/CAM (ICH3-S/ICH3-M) USB Controller #3'
class = serial bus
subclass = USB
pcib1@pci0:30:0: class=0x060400 card=0x00000000 chip=0x24488086 rev=0x42 hdr=0x01
vendor = 'Intel Corporation'
device = '82801BAM/CAM Hub Interface to PCI Bridge (Camino 2)'
class = bridge
subclass = PCI-PCI
isab0@pci0:31:0: class=0x060100 card=0x00000000 chip=0x248c8086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801CAM LPC Interface or ISA bridge: see Notes'
class = bridge
subclass = PCI-ISA
atapci0@pci0:31:1: class=0x01018a card=0x10171014 chip=0x248a8086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801CAM (ICH3-M) UltraATA/100 EIDE Controller'
class = mass storage
subclass = ATA
none1@pci0:31:3: class=0x0c0500 card=0x10171014 chip=0x24838086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801CA/CAM (ICH3-S/ICH3-M) SMBus Controller'
class = serial bus
subclass = SMBus
pcm0@pci0:31:5: class=0x040100 card=0x05001014 chip=0x24858086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801CA/CAM (ICH3-S/ICH3-M) AC'97 Audio Controller'
class = multimedia
subclass = audio
none2@pci0:31:6: class=0x070300 card=0x05031014 chip=0x24868086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801CA/CAM (ICH3-S/ICH3-M) AC'97 Modem Controller'
class = simple comms
fxp0@pci1:8:0: class=0x020000 card=0x10311014 chip=0x10318086 rev=0x42 hdr=0x00
vendor = 'Intel Corporation'
device = '82801CAM (ICH3) PRO/100 VE (LOM) Network Connection'
class = network
subclass = ethernet
pcic0@pci1:9:0: class=0x060700 card=0x10171014 chip=0xac50104c rev=0x02 hdr=0x02
vendor = 'Texas Instruments (TI)'
device = 'PCI1410 PC card cardBus Controller'
class = bridge
subclass = PCI-CardBus
======================
dmesg:
========
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.7-STABLE #1: Mon Nov 25 10:23:48 GMT 2002
pao@luthien.ukc.ac.uk:/usr/src/sys/compile/LUTHIEN
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (1133.21-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 259850240 (253760K bytes)
avail memory = 249737216 (243884K bytes)
Preloaded elf kernel "kernel" at 0xc0311000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc031109c.
Preloaded elf module "splash_bmp.ko" at 0xc03110ec.
Pentium Pro MTRR support enabled
module_register_init: MOD_LOAD (splash_bmp, c030c774, 0) error 2
pcibios: No call entry point
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82830 (i830M GMCH) SVGA controller> mem 0x90100000-0x9017ffff,0x98000000-0x9fffffff irq 11 at device 2.0 on pci0
agp0: detected 8060k stolen memory
agp0: aperture size is 128M
pci0: <unknown card> (vendor=0x8086, dev=0x3577) at 2.1
pci0: <UHCI USB controller> at 29.0 irq 11
pci0: <UHCI USB controller> at 29.1 irq 11
pci0: <UHCI USB controller> at 29.2 irq 11
pcib1: <PCI to PCI bridge (vendor=8086 device=2448)> at device 30.0 on pci0
pci1: <PCI bus> on pcib1
fxp0: <Intel Pro/100 Ethernet> port 0x7000-0x703f mem 0x80100000-0x80100fff irq 11 at device 8.0 on pci1
fxp0: Ethernet address 00:00:e2:82:2d:59
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcic0: <TI PCI-1410 PCI-CardBus Bridge> irq 11 at device 9.0 on pci1
pcic0: PCI Memory allocated: 0x88000000
pcic0: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
pccard0: <PC Card 16-bit bus (classic)> on pcic0
isab0: <PCI to ISA bridge (vendor=8086 device=248c)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 ATA100 controller> port 0xa890-0xa89f,0xa878-0xa87b,0xa860-0xa867,0xa848-0xa84b,0xa830-0xa837 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x2483) at 31.3 irq 11
pcm0: <Intel 82801CA (ICH3)> port 0x9c00-0x9c3f,0x9800-0x98ff irq 11 at device 31.5 on pci0
pci0: <unknown card> (vendor=0x8086, dev=0x2486) at 31.6 irq 11
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ad0: 19077MB <IC25N020ATCS04-0> [41344/15/63] at ata0-master UDMA100
acd0: CDROM <LG CD-ROM CRN-8245B> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s2a
pccard: card inserted, slot 0
pcic0: Card type 32-bit cardbus is unsupported
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0xa4a0-0xa4bf irq 11 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pccard: card removed, slot 0
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0xa4e0-0xa4ff irq 11 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port 0xa800-0xa81f irq 11 at device 29.2 on pci0
usb2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
==================
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20021125105914.B240>