Date: Fri, 3 Sep 1999 01:19:49 -0700 (PDT) From: Julian Elischer <julian@whistle.com> To: Rob Snow <rsnow@lgc.com> Cc: Poul-Henning Kamp <phk@critter.freebsd.dk>, freebsd-current@FreeBSD.ORG Subject: Re: spec_getpages error in current kernel from last night Message-ID: <Pine.BSF.4.05.9909030118180.41995-100000@home.elischer.org> In-Reply-To: <37CF7D9B.2CADAD88@lgc.com>
next in thread | previous in thread | raw e-mail | index | archive | help
As Poul says.. first thing.. do a cvsup now and try a very modern kernel. if that fails we'll have some more things to try by then. (my workstation just croaked so I'm busy rerouting around the problem) julian On Fri, 3 Sep 1999, Rob Snow wrote: > basil# uname -a > FreeBSD basil.dympna.com 4.0-CURRENT FreeBSD 4.0-CURRENT #0: Thu Sep 2 > 19:58:43 CDT 1999 > rsnow@basil.dympna.com:/stripe/current/src/sys/compile/Basil-SMP-Current > i386 > > Last cvsup was 2:03 on Sept 2 > > dmesg output: (I've snipped out non-existent di's and left the stuff > from my mucking with density for my Exabyte 8505, several modes weren't > supported) > > rsnow@basil% dmesg > Copyright (c) 1992-1999 The FreeBSD Project. > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights > reserved. > FreeBSD 4.0-CURRENT #0: Thu Sep 2 19:58:43 CDT 1999 > > rsnow@basil.dympna.com:/stripe/current/src/sys/compile/Basil-SMP-Current > Timecounter "i8254" frequency 1193182 Hz > CPU: Pentium Pro (686-class CPU) > Origin = "GenuineIntel" Id = 0x616 Stepping = 6 > > Features=0xfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV> > real memory = 134217728 (131072K bytes) > <SNIPED OUT di's of non-existent devices> > avail memory = 127070208 (124092K bytes) > Programming 24 pins in IOAPIC #0 > FreeBSD/SMP: Multiprocessor motherboard > cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000 > cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000 > io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000 > Preloaded elf kernel "kernel" at 0xc02f1000. > Preloaded userconfig_script "/boot/kernel.conf" at 0xc02f109c. > Pentium Pro MTRR support enabled > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcib0: <Host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > isab0: <Intel 82371SB PCI to ISA bridge> at device 7.0 on pci0 > isa0: <ISA bus> on isab0 > ide_pci0: <Intel PIIX3 Bus-master IDE controller> at device 7.1 on pci0 > fxp0: <Intel EtherExpress Pro 10/100B Ethernet> irq 16 at device 12.0 on > pci0 > fxp0: Ethernet address 00:a0:c9:93:da:0c > ahc0: <Adaptec 2940 SCSI adapter> irq 17 at device 13.0 on pci0 > ahc0: aic7870 Single Channel A, SCSI Id=7, 16/255 SCBs > vga-pci0: <Trident model 9660 VGA-compatible display device> irq 18 at > device 14.0 on pci0 > ahc1: <Adaptec 2940 Ultra SCSI adapter> irq 19 at device 15.0 on pci0 > ahc1: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f7 irq 6 drq 2 on isa0 > wdc0 at port 0x1f0-0x1f7 irq 14 on isa0 > wdc0: unit 0 (wd0): <Maxtor 7850 AV> > wd0: 814MB (1667232 sectors), 1654 cyls, 16 heads, 63 S/T, 512 B/S > atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > vga0: <Generic ISA VGA> at port 0x3b0-0x3df iomem 0xa0000-0xbffff on > isa0 > sc0: <System console> on isa0 > sc0: VGA <16 virtual consoles, flags=0x200> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1 at port 0x2f8-0x2ff irq 3 on isa0 > sio1: type 16550A > sio2: not probed (disabled) > sio3: not probed (disabled) > ppc0 at port 0x378-0x37f irq 7 flags 0x40 on isa0 > ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode > plip0: <PLIP network interface> on ppbus 0 > lpt0: <generic printer> on ppbus 0 > lpt0: Interrupt-driven port > ppi0: <generic parallel i/o> on ppbus 0 > APIC_IO: Testing 8254 interrupt delivery > APIC_IO: routing 8254 via pin 2 > Waiting 15 seconds for SCSI devices to settle > SMP: AP CPU #1 Launched! > sa0 at ahc0 bus 0 target 4 lun 0 > sa0: <EXABYTE EXB-85058SQANXR1 0781> Removable Sequential Access SCSI-2 > device > sa0: 5.000MB/s transfers (5.000MHz, offset 11) > da0 at ahc0 bus 0 target 3 lun 0 > da0: <MICROP 3243-19 1128RA 28RA> Fixed Direct Access SCSI-2 device > da0: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing > Enabled > da0: 4095MB (8388315 512 byte sectors: 255H 63S/T 522C) > da1 at ahc1 bus 0 target 6 lun 0 > da1: <SEAGATE ST39173W 5764> Fixed Direct Access SCSI-2 device > da1: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing > Enabled > da1: 8683MB (17783240 512 byte sectors: 255H 63S/T 1106C) > da2 at ahc1 bus 0 target 8 lun 0 > da2: <SEAGATE ST19171W 0023> Fixed Direct Access SCSI-2 device > da2: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing > Enabled > da2: 8683MB (17783112 512 byte sectors: 255H 63S/T 1106C) > changing root device to wd0s2a > vinum: loaded > vinum: reading configuration from /dev/da2s1e > vinum: updating configuration from /dev/da1s1e > (sa0:ahc0:0:4:0): MODE SELECT(06). CDB: 15 10 0 0 1c 0 > (sa0:ahc0:0:4:0): ILLEGAL REQUEST asc:26,0 > (sa0:ahc0:0:4:0): Invalid field in parameter list > (sa0:ahc0:0:4:0): MODE SELECT(06). CDB: 15 10 0 0 1c 0 > (sa0:ahc0:0:4:0): ILLEGAL REQUEST asc:26,0 > (sa0:ahc0:0:4:0): Invalid field in parameter list > (sa0:ahc0:0:4:0): MODE SELECT(06). CDB: 15 10 0 0 1c 0 > (sa0:ahc0:0:4:0): ILLEGAL REQUEST asc:26,0 > (sa0:ahc0:0:4:0): Invalid field in parameter list > (sa0:ahc0:0:4:0): MODE SELECT(06). CDB: 15 0 0 0 c 0 > (sa0:ahc0:0:4:0): ILLEGAL REQUEST asc:26,0 > (sa0:ahc0:0:4:0): Invalid field in parameter list > (sa0:ahc0:0:4:0): MODE SELECT(06). CDB: 15 0 0 0 c 0 > (sa0:ahc0:0:4:0): ILLEGAL REQUEST asc:26,0 > (sa0:ahc0:0:4:0): Invalid field in parameter list > (sa0:ahc0:0:4:0): MODE SELECT(06). CDB: 15 10 0 0 1c 0 > (sa0:ahc0:0:4:0): ILLEGAL REQUEST asc:26,0 > (sa0:ahc0:0:4:0): Invalid field in parameter list > (sa0:ahc0:0:4:0): MODE SELECT(06). CDB: 15 10 0 0 1c 0 > (sa0:ahc0:0:4:0): ILLEGAL REQUEST asc:26,0 > (sa0:ahc0:0:4:0): Invalid field in parameter list > spec_getpages: I/O read failure: (error code=0) bp 0xc44a3158 vp > 0xc9e071c0 > size: 0, resid: 0, a_count: 803, valid: 0x0 > nread: 0, reqpage: 0, pindex: 0, pcount: 1 > vm_fault: pager read error, pid 921 (cvsup) > pid 921 (cvsup), uid 0: exited on signal 6 (core dumped) > > > Poul-Henning Kamp wrote: > > > > can we have: > > > > uname -a, > > time of last cvsup/ctm > > and > > dmesg output > > > > please ? > > > > In message <37CF743A.452D81EF@lgc.com>, Rob Snow writes: > > >Just got this message while in cvsup: > > > > > >Sep 3 02:01:09 basil /kernel: spec_getpages: I/O read failure: (error > > >code=0) bp 0xc44a3158 vp 0xc9e071c0 > > >Sep 3 02:01:09 basil /kernel: size: 0, resid: 0, a_count: 803, valid: > > >0x0 > > >Sep 3 02:01:09 basil /kernel: nread: 0, reqpage: 0, pindex: 0, pcount: > > >1 > > >Sep 3 02:01:09 basil /kernel: vm_fault: pager read error, pid 921 > > >(cvsup) > > >Sep 3 02:01:09 basil /kernel: pid 921 (cvsup), uid 0: exited on signal > > >6 (core dumped) > > > > > >I'm guessing this is _bad_? > > > > > > > > >To Unsubscribe: send mail to majordomo@FreeBSD.org > > >with "unsubscribe freebsd-current" in the body of the message > > > > > > > -- > > Poul-Henning Kamp FreeBSD coreteam member > > phk@FreeBSD.ORG "Real hackers run -current on their laptop." > > FreeBSD -- It will take a long time before progress goes too far! > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > with "unsubscribe freebsd-current" in the body of the message > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-current" in the body of the message > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.05.9909030118180.41995-100000>