Date: Fri, 10 Feb 2012 22:12:37 -0800 From: Dennis Glatting <freebsd@penx.com> To: freebsd-scsi@freebsd.org, freebsd-current@freebsd.org Subject: Crash (was: LSI supported mps(4) driver available) Message-ID: <1328940757.65061.24.camel@btw.pki2.com> In-Reply-To: <20120120204459.GA51162@nargothrond.kdm.org> References: <20120120204459.GA51162@nargothrond.kdm.org>
next in thread | previous in thread | raw e-mail | index | archive | help
I'm starting to put this system under heavy load. I had three operations
working:
1) sftp a 1.7 TB file from a file server to a local, compressed (bzip)
data set (disk-1/zvol (below)).
2) An independent data processing function across a NFS mount into a
differnt file on the same data set (disk-1/zvol)
3) An independent data processing function across a NFS mount to disk-1
but not to a compressed data set (disk-1).
This is the second crash however the first was several days ago. I just
cvsup to RELENG_9 a couple of hours before I began these tasks.
Feb 10 21:47:16 bd3 kernel: mps0: mpssas_scsiio_timeout checking sc
0xffffff8000a19000 cm 0xffffff8000a7b700
Feb 10 21:47:16 bd3 kernel: (da3:mps0:0:3:0): SYNCHRONIZE CACHE(10).
CDB: 35 0 0 0 0 0 0 0 0 0 length 0 SMID 992 command timeout cm
0xffffff8000a7b700 ccb 0xfffffe00262ca800
Feb 10 21:47:16 bd3 kernel: mps0: mpssas_alloc_tm freezing simq
Feb 10 21:47:16 bd3 kernel: mps0: timedout cm 0xffffff8000a7b700
allocated tm 0xffffff8000a2c148
Feb 10 21:47:16 bd3 kernel: mps0: mpssas_scsiio_timeout checking sc
0xffffff8000a19000 cm 0xffffff8000a77fe8
Feb 10 21:47:16 bd3 kernel: (da0:mps0:0:0:0): SYNCHRONIZE CACHE(10).
CDB: 35 0 0 0 0 0 0 0 0 0 length 0 SMID 949 command timeout cm
0xffffff8000a77fe8 ccb 0xfffffe00262c9000
Feb 10 21:47:16 bd3 kernel: mps0: timedout cm 0xffffff8000a77fe8
allocated tm 0xffffff8000a2c290
Feb 10 21:47:16 bd3 kernel: mps0: mpssas_scsiio_timeout checking sc
0xffffff8000a19000 cm 0xffffff8000a672d8
Feb 10 21:47:16 bd3 kernel: (da6:mps0:0:6:0): SYNCHRONIZE CACHE(10).
CDB: 35 0 0 0 0 0 0 0 0 0 length 0 SMID 739 command timeout cm
0xffffff8000a672d8 ccb 0xfffffe00262c2000
Feb 10 21:47:16 bd3 kernel: mps0: timedout cm 0xffffff8000a672d8
allocated tm 0xffffff8000a2c3d8
Feb 10 21:47:16 bd3 kernel: mps0: mpssas_scsiio_timeout checking sc
0xffffff8000a19000 cm 0xffffff8000a58718
Feb 10 21:47:16 bd3 kernel: (da4:mps0:0:4:0): SYNCHRONIZE CACHE(10).
CDB: 35 0 0 0 0 0 0 0 0 0 length 0 SMID 555 command timeout cm
0xffffff8000a58718 ccb 0xfffffe00262c7800
Feb 10 21:47:16 bd3 kernel: mps0: timedout cm 0xffffff8000a58718
allocated tm 0xffffff8000a2c520
Feb 10 21:47:16 bd3 kernel: mps2: mpssas_scsiio_timeout checking sc
0xffffff8000b5e000 cm 0xffffff8000bb3c90
Feb 10 21:47:16 bd3 kernel: (da11:mps2:0:2:0): SYNCHRONIZE CACHE(10).
CDB: 35 0 0 0 0 0 0 0 0 0 length 0 SMID 834 command timeout cm
0xffffff8000bb3c90 ccb 0xfffffe002636e000
Feb 10 21:47:16 bd3 kernel: mps2: mpssas_alloc_tm freezing simq
Feb 10 21:47:16 bd3 kernel: mps2: timedout cm 0xffffff8000bb3c90
allocated tm 0xffffff8000b71148
Feb 10 21:47:16 bd3 upsd[2135]: UPS [cyberpower] data is no longer stale
Feb 10 21:47:16 bd3 kernel: (da11:mps2:0:2:0): SYNCHRONIZE CACHE(10).
CDB: 35 0 0 0 0 0 0 0 0 0 length 0 SMID 834 completed timedout cm
0xffffff8000bb3c90 ccb 0xfffffe002636e000 during recove
ry ioc 8048 scsi 0 state c x(noperiph:mps2:0:2:0): SMID 1 abort TaskMID
834 status 0x0 code 0x0 count 1
Feb 10 21:47:16 bd3 kernel: (noperiph:mps2:0:2:0): SMID 1 finished
recovery after aborting TaskMID 834
Feb 10 21:47:16 bd3 kernel: mps2: mpssas_free_tm releasing simq
(same stuff, yada, yada, yada)
Reboot and a dmesg:
bd3> dmesg
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights
reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.0-STABLE #3: Fri Feb 10 19:19:33 PST 2012
root@bd3:/sys/amd64/compile/SMUNI amd64
CPU: AMD FX(tm)-8150 Eight-Core Processor (4017.98-MHz
K8-class CPU)
Origin = "AuthenticAMD" Id = 0x600f12 Family = 15 Model = 1
Stepping = 2
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Features2=0x1698220b<SSE3,PCLMULQDQ,MON,SSSE3,CX16,SSE4.1,SSE4.2,POPCNT,AESNI,XSAVE,AVX>
AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM>
AMD
Features2=0x1c9bfff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,XOP,SKINIT,WDT,LWP,FMA4,NodeId,Topology,<b23>,<b24>>
TSC: P-state invariant, performance statistics
real memory = 17179869184 (16384 MB)
avail memory = 16507547648 (15742 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <GBT GBTUACPI>
FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
FreeBSD/SMP: 1 package(s) x 8 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 2
cpu3 (AP): APIC ID: 3
cpu4 (AP): APIC ID: 4
cpu5 (AP): APIC ID: 5
cpu6 (AP): APIC ID: 6
cpu7 (AP): APIC ID: 7
ioapic0: Changing APIC ID to 8
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
cryptosoft0: <software crypto> on motherboard
aesni0: <AES-CBC,AES-XTS> on motherboard
acpi0: <GBT GBTUACPI> on motherboard
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, cfca0000 (3) failed
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
cpu4: <ACPI CPU> on acpi0
cpu5: <ACPI CPU> on acpi0
cpu6: <ACPI CPU> on acpi0
cpu7: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <base peripheral> at device 0.2 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> irq 19 at device 3.0 on pci0
pci1: <ACPI PCI bus> on pcib1
mps0: <LSI SAS2008> port 0xde00-0xdeff mem
0xfd9fc000-0xfd9fffff,0xfd980000-0xfd9bffff irq 19 at device 0.0 on pci1
mps0: Firmware: 12.00.00.00, Driver: 11.255.03.00-fbsd
mps0: IOCCapabilities:
1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDisc>
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 4.0 on pci0
pci2: <ACPI PCI bus> on pcib2
em0: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0xcf00-0xcf1f mem
0xfd7c0000-0xfd7dffff,0xfd700000-0xfd77ffff,0xfd7fc000-0xfd7fffff irq 16
at device 0.0 on pci2
em0: Using MSIX interrupts with 3 vectors
em0: Ethernet address: 00:1b:21:c6:d2:a0
pcib3: <ACPI PCI-PCI bridge> irq 17 at device 9.0 on pci0
pci3: <ACPI PCI bus> on pcib3
xhci0: <XHCI (generic) USB 3.0 controller> mem 0xfd5f8000-0xfd5fffff irq
17 at device 0.0 on pci3
xhci0: 64 byte context size.
usbus0 on xhci0
pcib4: <ACPI PCI-PCI bridge> irq 18 at device 10.0 on pci0
pci4: <ACPI PCI bus> on pcib4
ahci0: <Marvell 88SE9172 AHCI SATA controller> port
0xaf00-0xaf07,0xae00-0xae03,0xad00-0xad07,0xac00-0xac03,0xab00-0xab0f
mem 0xfcbff000-0xfcbff1ff irq 18 at device 0.0 on pci4
ahci0: AHCI v1.00 with 2 6Gbps ports, Port Multiplier supported with FBS
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
pcib5: <ACPI PCI-PCI bridge> irq 19 at device 11.0 on pci0
pci5: <ACPI PCI bus> on pcib5
mps1: <LSI SAS2008> port 0x9e00-0x9eff mem
0xfdefc000-0xfdefffff,0xfde80000-0xfdebffff irq 19 at device 0.0 on pci5
mps1: Firmware: 12.00.00.00, Driver: 11.255.03.00-fbsd
mps1: IOCCapabilities:
185c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,IR>
pcib6: <ACPI PCI-PCI bridge> irq 16 at device 12.0 on pci0
pci6: <ACPI PCI bus> on pcib6
mps2: <LSI SAS2008> port 0x8e00-0x8eff mem
0xfdcfc000-0xfdcfffff,0xfdc80000-0xfdcbffff irq 16 at device 0.0 on pci6
mps2: Firmware: 12.00.00.00, Driver: 11.255.03.00-fbsd
mps2: IOCCapabilities:
1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDisc>
pcib7: <ACPI PCI-PCI bridge> irq 17 at device 13.0 on pci0
pci7: <ACPI PCI bus> on pcib7
vgapci0: <VGA-compatible display> port 0xee00-0xeeff mem
0xd0000000-0xdfffffff,0xfdac0000-0xfdadffff irq 17 at device 0.0 on pci7
hdac0: <ATI (Unknown) High Definition Audio Controller> mem
0xfdafc000-0xfdafffff irq 18 at device 0.1 on pci7
ahci1: <ATI IXP700 AHCI SATA controller> port
0xff00-0xff07,0xfe00-0xfe03,0xfd00-0xfd07,0xfc00-0xfc03,0xfb00-0xfb0f
mem 0xfdfff000-0xfdfff3ff irq 19 at device 17.0 on pci0
ahci1: AHCI v1.20 with 4 6Gbps ports, Port Multiplier supported
ahcich2: <AHCI channel> at channel 0 on ahci1
ahcich3: <AHCI channel> at channel 1 on ahci1
ahcich4: <AHCI channel> at channel 2 on ahci1
ahcich5: <AHCI channel> at channel 3 on ahci1
ohci0: <OHCI (generic) USB controller> mem 0xfdffe000-0xfdffefff irq 18
at device 18.0 on pci0
usbus1: <OHCI (generic) USB controller> on ohci0
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfdffd000-0xfdffd0ff irq
17 at device 18.2 on pci0
usbus2: EHCI version 1.0
usbus2: <EHCI (generic) USB 2.0 controller> on ehci0
ohci1: <OHCI (generic) USB controller> mem 0xfdffc000-0xfdffcfff irq 18
at device 19.0 on pci0
usbus3: <OHCI (generic) USB controller> on ohci1
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfdffb000-0xfdffb0ff irq
17 at device 19.2 on pci0
usbus4: EHCI version 1.0
usbus4: <EHCI (generic) USB 2.0 controller> on ehci1
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci0: <ATI IXP700/800 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfa00-0xfa0f at device 20.1 on pci0
ata0: <ATA channel> at channel 0 on atapci0
ata1: <ATA channel> at channel 1 on atapci0
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib8: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci8: <ACPI PCI bus> on pcib8
ath0: <Atheros 9280> mem 0xfd4e0000-0xfd4effff irq 20 at device 6.0 on
pci8
[ath] enabling AN_TOP2_FIXUP
[ath]: default pwr offset: -5 dBm != EEPROM pwr offset: 0 dBm; curves
will be adjusted.
ath0: AR9280 mac 128.2 RF5133 phy 13.0
ohci2: <OHCI (generic) USB controller> mem 0xfdffa000-0xfdffafff irq 18
at device 20.5 on pci0
usbus5: <OHCI (generic) USB controller> on ohci2
pcib9: <ACPI PCI-PCI bridge> at device 21.0 on pci0
pci9: <ACPI PCI bus> on pcib9
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port
0x6e00-0x6eff mem 0xfd0ff000-0xfd0fffff,0xfd0f8000-0xfd0fbfff irq 17 at
device 0.0 on pci9
re0: Using 1 MSI-X message
re0: Chip rev. 0x2c800000
re0: MAC rev. 0x00000000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on
miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX,
100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master,
1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow,
1000baseT-FDX-flow-master, auto, auto-flow
re0: Ethernet address: 50:e5:49:45:55:8e
pcib10: <ACPI PCI-PCI bridge> at device 21.1 on pci0
pci10: <ACPI PCI bus> on pcib10
xhci1: <XHCI (generic) USB 3.0 controller> mem 0xfcff8000-0xfcffffff irq
17 at device 0.0 on pci10
xhci1: 64 byte context size.
usbus6 on xhci1
pcib11: <ACPI PCI-PCI bridge> at device 21.2 on pci0
pci11: <ACPI PCI bus> on pcib11
ahci2: <Marvell 88SE9172 AHCI SATA controller> port
0x3f00-0x3f07,0x3e00-0x3e03,0x3d00-0x3d07,0x3c00-0x3c03,0x3b00-0x3b0f
mem 0xfcdff000-0xfcdff1ff irq 17 at device 0.0 on pci11
ahci2: AHCI v1.00 with 2 6Gbps ports, Port Multiplier supported with FBS
ahcich6: <AHCI channel> at channel 0 on ahci2
ahcich7: <AHCI channel> at channel 1 on ahci2
ohci3: <OHCI (generic) USB controller> mem 0xfdff9000-0xfdff9fff irq 18
at device 22.0 on pci0
usbus7: <OHCI (generic) USB controller> on ohci3
ehci2: <EHCI (generic) USB 2.0 controller> mem 0xfdff8000-0xfdff80ff irq
17 at device 22.2 on pci0
usbus8: EHCI version 1.0
usbus8: <EHCI (generic) USB 2.0 controller> on ehci2
attimer0: <AT timer> port 0x40-0x43 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff irq 0,8
on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
atrtc0: <AT realtime clock> port 0x70-0x73 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcffff,0xd6000-0xd6fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: cannot reserve I/O port range
hwpstate0: <Cool`n'Quiet 2.0> on cpu0
Timecounters tick every 1.000 msec
hdac0: HDA Codec #0: ATI R6xx HDMI
pcm0: <HDA ATI R6xx HDMI PCM #0 HDMI> at cad 0 nid 1 on hdac0
usbus0: 5.0Gbps Super Speed USB v3.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 5.0Gbps Super Speed USB v3.0
usbus7: 12Mbps Full Speed USB v1.0
usbus8: 480Mbps High Speed USB v2.0
ugen0.1: <0x1b6f> at usbus0
uhub0: <0x1b6f XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on
usbus0
ugen1.1: <ATI> at usbus1
uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <ATI> at usbus2
uhub2: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <ATI> at usbus3
uhub3: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <ATI> at usbus4
uhub4: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
ugen5.1: <ATI> at usbus5
uhub5: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <0x1b6f> at usbus6
uhub6: <0x1b6f XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on
usbus6
ugen7.1: <ATI> at usbus7
uhub7: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus7
ugen8.1: <ATI> at usbus8
uhub8: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus8
uhub5: 2 ports with 2 removable, self powered
uhub7: 4 ports with 4 removable, self powered
uhub1: 5 ports with 5 removable, self powered
uhub3: 5 ports with 5 removable, self powered
uhub0: 4 ports with 4 removable, self powered
uhub6: 4 ports with 4 removable, self powered
uhub8: 4 ports with 4 removable, self powered
uhub2: 5 ports with 5 removable, self powered
uhub4: 5 ports with 5 removable, self powered
ugen1.2: <BTC> at usbus1
ukbd0: <BTC USB Multimedia Keyboard, class 0/0, rev 1.10/1.00, addr 2>
on usbus1
kbd2 at ukbd0
ugen3.2: <CPS> at usbus3
uhid0: <BTC USB Multimedia Keyboard, class 0/0, rev 1.10/1.00, addr 2>
on usbus1
(probe255:mps1:0:0:0): REPORT LUNS. CDB: a0 0 0 0 0 0 0 0 0 10 0 0
(probe255:mps1:0:0:0): CAM status: SCSI Status Error
(probe255:mps1:0:0:0): SCSI status: Check Condition
(probe255:mps1:0:0:0): SCSI sense: ILLEGAL REQUEST asc:20,0 (Invalid
command operation code)
(probe255:mps1:0:0:0): Command Specific Info: 0xd44603c0
(probe255:mps1:0:0:0): REPORT LUNS. CDB: a0 0 0 0 0 0 0 0 0 10 0 0
(probe255:mps1:0:0:0): CAM status: SCSI Status Error
(probe255:mps1:0:0:0): SCSI status: Check Condition
(probe255:mps1:0:0:0): SCSI sense: ILLEGAL REQUEST asc:20,0 (Invalid
command operation code)
(probe255:mps1:0:0:0): Field Replaceable Unit: 55
(probe255:mps1:0:0:0): Command Specific Info: 0x36343236
ada0 at ahcich2 bus 0 scbus5 target 0 lun 0
ada0: <Corsair Force 3 SSD 1.3.3> ATA-8 SATA 3.x device
ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 85857MB (175836528 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad8
ada1 at ahcich3 bus 0 scbus6 target 0 lun 0
ada1: <OCZ-AGILITY2 1.33> ATA-8 SATA 2.x device
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 57241MB (117231408 512 byte sectors: 16H 63S/T 16383C)
ada1: Previously was known as ad10
da8 at mps1 bus 0 scbus3 target 0 lun 0
da8: <LSI Logical Volume 3000> Fixed Direct Access SCSI-6 device
da8: 150.000MB/s transfers
da8: Command Queueing enabled
da8: 952720MB (1951170560 512 byte sectors: 255H 63S/T 121454C)
SMP: AP CPU #4 Launched!
da4 at mps0 bus 0 scbus0 target 4 lun 0
da4: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da4: 300.000MB/s transfers
da4: Command Queueing enabled
da4: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da0 at mps0 bus 0 scbus0 target 0 lun 0
da0: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da0: 300.000MB/s transfers
da0: Command Queueing enabled
da0: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da3 at mps0 bus 0 scbus0 target 3 lun 0
da3: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da3: 300.000MB/s transfers
da3: Command Queueing enabled
da3: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
SMP: AP CPU #2 Launched!
da5 at mps0 bus 0 scbus0 target 5 lun 0
da5: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da5: 300.000MB/s transfers
da5: Command Queueing enabled
da5: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da6 at mps0 bus 0 scbus0 target 6 lun 0
da6: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da6: 300.000MB/s transfers
da6: Command Queueing enabled
da6: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da7 at mps0 bus 0 scbus0 target 7 lun 0
da7: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da7: 300.000MB/s transfers
da7: Command Queueing enabled
da7: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
SMP: AP CPU #3 Launched!
da10 at mps2 bus 0 scbus4 target 1 lun 0
da10: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da10: 300.000MB/s transfers
da10: Command Queueing enabled
da10: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da11 at mps2 bus 0 scbus4 target 2 lun 0
da11: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da11: 300.000MB/s transfers
da11: Command Queueing enabled
da11: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da9 at mps2 bus 0 scbus4 target 0 lun 0
da9: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da9: 300.000MB/s transfers
da9: Command Queueing enabled
da9: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
SMP: AP CPU #6 Launched!
da12 at mps2 bus 0 scbus4 target 3 lun 0
da12: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da12: 300.000MB/s transfers
da12: Command Queueing enabled
da12: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da2 at mps0 bus 0 scbus0 target 2 lun 0
da2: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da2: 300.000MB/s transfers
da2: Command Queueing enabled
da2: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
da1 at mps0 bus 0 scbus0 target 1 lun 0
da1: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
da1: 300.000MB/s transfers
da1: Command Queueing enabled
da1: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
SMP: AP CPU #5 Launched!
SMP: AP CPU #7 Launched!
SMP: AP CPU #1 Launched!
Timecounter "TSC-low" frequency 15695252 Hz quality 1000
da13 at mps2 bus 0 scbus4 target 4 lun 0
da13: <ATA ST31000333AS SD35> Fixed Direct Access SCSI-6 device
da13: 300.000MB/s transfers
da13: Command Queueing enabled
da13: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C)
Trying to mount root from ufs:/dev/gpt/disk0 [rw]...
WARNING: / was not properly dismounted
ZFS filesystem version 5
ZFS storage pool version 28
bd3>
The pools after reboot:
bd3> zpool status
pool: disk-1
state: ONLINE
scan: scrub repaired 0 in 0h0m with 0 errors on Fri Feb 10 22:00:32
2012
config:
NAME STATE READ WRITE CKSUM
disk-1 ONLINE 0 0 0
raidz1-0 ONLINE 0 0 0
da3 ONLINE 0 0 0
da2 ONLINE 0 0 0
da1 ONLINE 0 0 0
da0 ONLINE 0 0 0
da7 ONLINE 0 0 0
da6 ONLINE 0 0 0
da5 ONLINE 0 0 0
da4 ONLINE 0 0 0
da12 ONLINE 0 0 0
da11 ONLINE 0 0 0
da10 ONLINE 0 0 0
da9 ONLINE 0 0 0
cache
ada0 ONLINE 0 0 0
errors: No known data errors
pool: disk-2
state: ONLINE
scan: scrub repaired 0 in 0h0m with 0 errors on Fri Feb 10 22:00:47
2012
config:
NAME STATE READ WRITE CKSUM
disk-2 ONLINE 0 0 0
da13 ONLINE 0 0 0
errors: No known data errors
bd3>
The volumes:
bd3> df -lh
Filesystem Size Used Avail Capacity Mounted on
/dev/gpt/disk0 901G 6G 823G 1% /
devfs 1.0k 1.0k 0B 100% /dev
disk-1 24T 1.2G 24T 0% /disk-1
disk-1/zvol 24T 67k 24T 0% /disk-1/zvol
disk-2 913G 1.6G 911G 0% /disk-2
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1328940757.65061.24.camel>