Date: Fri, 01 Dec 2000 16:51:55 -0800 From: Philippe Le Berre <philippe@le-berre.com> To: hardware@freebsd.org Subject: Trouble with IBM UltraStar 18GB Message-ID: <5.0.1.4.0.20001201163731.0191feb0@puccini.grenoble.hp.com>
next in thread | raw e-mail | index | archive | help
Hi,
I have a brand new system, the mother board is a Tyan Thunder LE S2510 with
1 GB of RAM and a 18 GB UltraStar (IBM DDYS-T18350N S93E). I have no
trouble installing FreeBSD 4.1.1 release on it, but once I have cvsupped
stable and try to run make buildworld it quickly fails with a 'error in
wait: -1' at different points. If I set all the volumes with the sync
option, then the buildworld goes close to the end but fails also with
either a 'gcc execute error' or 'error in wait: -1'. Thinking of a bad luck
with a firmware I have switched the 18GB with another one (exact same kind)
and change the cables, but that doesn't help ... I am stucked!
Is there known issues with those drives? The mother board is certified by
Tyan with FreeBSD 4.1, so I would not think of issues with it, am I wrong?
I need to try with the UDMA66 drive I have plugged (Maxtor) into as soon as
possible, but all advices, experiences and opinions are welcomed. I would
really like to be able to use those UltraStars & SCSI-3!
thanks,
-philippe
------------->> dmesg -------->>>-------------------
Copyright (c) 1992-2000 The FreeBSD
Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1.1-RELEASE #0: Tue Sep 26 00:46:59 GMT 2000
jkh@narf.osd.bsdi.com:/usr/src/sys/compile/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (797.48-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR
,XMM>
real memory = 1073741824 (1048576K bytes)
avail memory = 1041694720 (1017280K bytes)
Preloaded elf kernel "kernel" at 0xc0416000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <RCC LE host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pci0: <ATI Mach64-GR graphics accelerator> at 1.0 irq 11
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xd400-0xd43f mem
0xfe900000-0xfe9fffff,0xfeafe000-0xfeafef
ff irq 9 at device 4.0 on pci0
fxp0: Ethernet address 00:e0:81:01:3f:51
fxp1: <Intel Pro 10/100B/100+ Ethernet> port 0xd000-0xd03f mem
0xfe700000-0xfe7fffff,0xfeafd000-0xfeafdf
ff irq 5 at device 5.0 on pci0
fxp1: Ethernet address 00:e0:81:01:3f:52
isab0: <PCI to ISA bridge (vendor=1166 device=0200)> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Generic PCI ATA controller> port 0xffa0-0xffaf at device 15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
ohci0: <OHCI (generic) USB controller> mem 0xfeafc000-0xfeafcfff irq 10 at
device 15.2 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (unknown) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
pcib1: <RCC LE host to PCI bridge> on
motherboard
pci1: <PCI bus> on pcib1
sym0: <1010-33> port 0xe400-0xe4ff mem
0xfebd8000-0xfebd9fff,0xfebe0000-0xfebe03ff irq 7 at device 6.0 o
n pci1
sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: handling phase mismatch from SCRIPTS.
sym1: <1010-33> port 0xe800-0xe8ff mem
0xfebf0000-0xfebf1fff,0xfebf8000-0xfebf83ff irq 10 at device 6.1
on pci1
sym1: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: using LOAD/STORE-based firmware.
sym1: handling phase mismatch from SCRIPTS.
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: parallel port not found.
ad0: 14655MB <Maxtor 51536H2> [29777/16/63] at ata0-master using BIOSDMA
acd0: CDROM <MATSHITA CR-175> at ata1-slave using PIO4
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
(noperiph:sym1:0:-1:-1): SCSI BUS reset delivered.
Mounting root from ufs:/dev/da0s1a
da0 at sym0 bus 0 target 1 lun 0
da0: <IBM DDYS-T18350N S93E> Fixed Direct Access SCSI-3
device
da0: 160.000MB/s transfers (80.000MHz, offset 62, 16bit), Tagged Queueing
Enabled
da0: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hardware" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?5.0.1.4.0.20001201163731.0191feb0>