Date: Fri, 8 Oct 2004 18:53:53 +1000 (EST) From: PeterJeremy@optushome.com.au To: FreeBSD-gnats-submit@FreeBSD.org Cc: andrew.li@alcatel.com.au Subject: kern/72441: HP Proliant DL380 hangs on reboot with 5.3 Message-ID: <200410080853.i988rr5X032066@cirb503493.alcatel.com.au> Resent-Message-ID: <200410080900.i9890ZZl098550@freefall.freebsd.org>
next in thread | raw e-mail | index | archive | help
>Number: 72441 >Category: kern >Synopsis: HP Proliant DL380 hangs on reboot with 5.3 >Confidential: no >Severity: critical >Priority: high >Responsible: freebsd-bugs >State: open >Quarter: >Keywords: >Date-Required: >Class: sw-bug >Submitter-Id: current-users >Arrival-Date: Fri Oct 08 09:00:35 GMT 2004 >Closed-Date: >Last-Modified: >Originator: Peter Jeremy >Release: FreeBSD 5.3-BETA6 i386 >Organization: Alcatel Australia Limited >Environment: System: FreeBSD srpca.alcatel.com.au 5.3-BETA6 FreeBSD 5.3-BETA6 #1: Tue Oct 5 13:52:33 EST 2004 root@srpca.alcatel.com.au:/var/obj/usr/src/sys/GENERIC i386 System: FreeBSD srpca.alcatel.com.au 5.3-BETA7 FreeBSD 5.3-BETA7 #4: Fri Oct 8 11:11:27 EST 2004 root@srpca.alcatel.com.au:/var/obj/usr/src/sys/GENERIC i386 [This is a CTM upgrade as of 6th October 1358UTC] >Description: A DL380 running FreeBSD 5 will not automatically reboot after a 'reboot' command or panic. It hangs at the 'Rebooting...' message and must be powered off/on to recover. Other notes: - This problem exists with or without ACPI enabled. - The reboot after installing 5.3-BETA6 hung. - You can reboot from single-user mode but not from multi-user mode. - Enabling BROKEN_KEYBOARD_RESET in the kernel has no effect. - 'up'ing the onboard Broadcom NICs in single-user mode has no effect. - The problem doesn't exist in 4.10 [This problem is critical to us and will block our deployment of 5.3 because the systems are used for incoming remote access at unmanned sites.] A verbose boot of 5.3-BETA7 follows (cut from /var/log/messages): Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.3-BETA7 #3: Thu Oct 7 12:51:47 EST 2004 root@srpca.alcatel.com.au:/var/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a1f000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a1f244. Table 'FACP' at 0x3fffa040 Table 'APIC' at 0x3fffa100 MADT: Found table at 0x3fffa100 MP Configuration Table version 1.4 found at 0xc00f29ca APIC: Using the MADT enumerator. MADT: Found CPU APIC ID 0 ACPI ID 0: disabled MADT: Found CPU APIC ID 2 ACPI ID 2: disabled MADT: Found CPU APIC ID 4 ACPI ID 4: disabled MADT: Found CPU APIC ID 6 ACPI ID 6: enabled SMP: Added CPU 6 (AP) MADT: Found CPU APIC ID 1 ACPI ID 1: disabled MADT: Found CPU APIC ID 3 ACPI ID 3: disabled MADT: Found CPU APIC ID 5 ACPI ID 5: disabled MADT: Found CPU APIC ID 7 ACPI ID 7: disabled ACPI APIC Table: <COMPAQ 00000083> Calibrating clock(s) ... i8254 clock: 1193108 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 2790957984 Hz CPU: Intel(R) Xeon(TM) CPU 2.80GHz (2790.96-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Hyperthreading: 2 logical CPUs real memory = 1073717248 (1023 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000000c29000 - 0x000000003edc9fff, 1041895424 bytes (254369 pages) avail memory = 1041158144 (992 MB) bios32: Found BIOS32 Service Directory header at 0xc00ffee0 bios32: Entry = 0xf0000 (c00f0000) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0x94 Other BIOS signatures found: APIC: CPU 0 has ACPI ID 6 MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000 ioapic0: Routing external 8259A's -> intpin 0 ioapic0: intpin 0 -> ExtINT (edge, high) ioapic0: intpin 1 -> ISA IRQ 1 (edge, high) ioapic0: intpin 2 -> ISA IRQ 2 (edge, high) ioapic0: intpin 3 -> ISA IRQ 3 (edge, high) ioapic0: intpin 4 -> ISA IRQ 4 (edge, high) ioapic0: intpin 5 -> ISA IRQ 5 (edge, high) ioapic0: intpin 6 -> ISA IRQ 6 (edge, high) ioapic0: intpin 7 -> ISA IRQ 7 (edge, high) ioapic0: intpin 8 -> ISA IRQ 8 (edge, high) ioapic0: intpin 9 -> ISA IRQ 9 (edge, high) ioapic0: intpin 10 -> ISA IRQ 10 (edge, high) ioapic0: intpin 11 -> ISA IRQ 11 (edge, high) ioapic0: intpin 12 -> ISA IRQ 12 (edge, high) ioapic0: intpin 13 -> ISA IRQ 13 (edge, high) ioapic0: intpin 14 -> ISA IRQ 14 (edge, high) ioapic0: intpin 15 -> ISA IRQ 15 (edge, high) MADT: Found IO APIC ID 3, Interrupt 16 at 0xfec01000 ioapic1: intpin 0 -> PCI IRQ 16 (level, low) ioapic1: intpin 1 -> PCI IRQ 17 (level, low) ioapic1: intpin 2 -> PCI IRQ 18 (level, low) ioapic1: intpin 3 -> PCI IRQ 19 (level, low) ioapic1: intpin 4 -> PCI IRQ 20 (level, low) ioapic1: intpin 5 -> PCI IRQ 21 (level, low) ioapic1: intpin 6 -> PCI IRQ 22 (level, low) ioapic1: intpin 7 -> PCI IRQ 23 (level, low) ioapic1: intpin 8 -> PCI IRQ 24 (level, low) ioapic1: intpin 9 -> PCI IRQ 25 (level, low) ioapic1: intpin 10 -> PCI IRQ 26 (level, low) ioapic1: intpin 11 -> PCI IRQ 27 (level, low) ioapic1: intpin 12 -> PCI IRQ 28 (level, low) ioapic1: intpin 13 -> PCI IRQ 29 (level, low) ioapic1: intpin 14 -> PCI IRQ 30 (level, low) ioapic1: intpin 15 -> PCI IRQ 31 (level, low) MADT: Found IO APIC ID 4, Interrupt 32 at 0xfec02000 ioapic2: intpin 0 -> PCI IRQ 32 (level, low) ioapic2: intpin 1 -> PCI IRQ 33 (level, low) ioapic2: intpin 2 -> PCI IRQ 34 (level, low) ioapic2: intpin 3 -> PCI IRQ 35 (level, low) ioapic2: intpin 4 -> PCI IRQ 36 (level, low) ioapic2: intpin 5 -> PCI IRQ 37 (level, low) ioapic2: intpin 6 -> PCI IRQ 38 (level, low) ioapic2: intpin 7 -> PCI IRQ 39 (level, low) ioapic2: intpin 8 -> PCI IRQ 40 (level, low) ioapic2: intpin 9 -> PCI IRQ 41 (level, low) ioapic2: intpin 10 -> PCI IRQ 42 (level, low) ioapic2: intpin 11 -> PCI IRQ 43 (level, low) ioapic2: intpin 12 -> PCI IRQ 44 (level, low) ioapic2: intpin 13 -> PCI IRQ 45 (level, low) ioapic2: intpin 14 -> PCI IRQ 46 (level, low) ioapic2: intpin 15 -> PCI IRQ 47 (level, low) MADT: Found IO APIC ID 5, Interrupt 48 at 0xfec03000 ioapic3: intpin 0 -> PCI IRQ 48 (level, low) ioapic3: intpin 1 -> PCI IRQ 49 (level, low) ioapic3: intpin 2 -> PCI IRQ 50 (level, low) ioapic3: intpin 3 -> PCI IRQ 51 (level, low) ioapic3: intpin 4 -> PCI IRQ 52 (level, low) ioapic3: intpin 5 -> PCI IRQ 53 (level, low) ioapic3: intpin 6 -> PCI IRQ 54 (level, low) ioapic3: intpin 7 -> PCI IRQ 55 (level, low) ioapic3: intpin 8 -> PCI IRQ 56 (level, low) ioapic3: intpin 9 -> PCI IRQ 57 (level, low) ioapic3: intpin 10 -> PCI IRQ 58 (level, low) ioapic3: intpin 11 -> PCI IRQ 59 (level, low) ioapic3: intpin 12 -> PCI IRQ 60 (level, low) ioapic3: intpin 13 -> PCI IRQ 61 (level, low) ioapic3: intpin 14 -> PCI IRQ 62 (level, low) ioapic3: intpin 15 -> PCI IRQ 63 (level, low) MADT: intr override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 ioapic0: intpin 2 trigger: edge ioapic0: intpin 2 polarity: high lapic: Routing NMI -> LINT1 MADT: Forcing active-low polarity and level trigger for SCI ioapic0: intpin 9 polarity: low ioapic0: intpin 9 trigger: level ioapic0 <Version 1.1> irqs 0-15 on motherboard ioapic1 <Version 1.1> irqs 16-31 on motherboard ioapic2 <Version 1.1> irqs 32-47 on motherboard ioapic3 <Version 1.1> irqs 48-63 on motherboard cpu0 BSP: ID: 0x06000000 VER: 0x00050014 LDR: 0x01000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff wlan: <802.11 Link Layer> random: <entropy source, Software, Yarrow> io: <I/O> mem: <memory> Pentium Pro MTRR support enabled null: <null device, zero device> npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <COMPAQ P29> on motherboard acpi0: [MPSAFE] acpi0: Power Button (fixed) pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00141166) pcibios: BIOS version 2.10 AcpiOsDerivePciId: bus 0 dev 0 func 0 ACPI timer looks GOOD min = 3, max = 5, width = 2 sage repeated 7 times ACPI timer looks BAD min = 3, max = 6, width = 3 ACPI timer looks BAD min = 3, max = 360, width = 357 Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x920-0x923 on acpi0 cpu0: <ACPI CPU> on acpi0 acpi_tz0: <Thermal Zone> on acpi0 pcib0: <ACPI Host-PCI bridge> on acpi0 ACPI PCI link initial configuration: \_SB_.IUSB irq 0: [ 4 5 7 10 11 15] 0+ low,level,sharable 0.15.0 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 found-> vendor=0x1166, dev=0x0014, revid=0x33 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1166, dev=0x0014, revid=0x00 bus=0, slot=0, func=1 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1166, dev=0x0014, revid=0x00 bus=0, slot=0, func=2 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 1, range 32, base f6000000, size 24, enabled map[14]: type 4, range 32, base 00002400, size 8, enabled map[18]: type 1, range 32, base f5ff0000, size 12, enabled found-> vendor=0x1002, dev=0x4752, revid=0x27 bus=0, slot=3, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0087, statreg=0x0290, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 4, range 32, base 00001800, size 8, enabled map[14]: type 1, range 32, base f5fe0000, size 9, enabled pcib0: matched entry for 0.4.INTA pcib0: slot 4 INTA hardwired to IRQ 16 found-> vendor=0x0e11, dev=0xb203, revid=0x01 bus=0, slot=4, func=0 class=08-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0103, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=16 powerspec 2 supports D0 D3 current D0 map[10]: type 4, range 32, base 00002800, size 8, enabled map[14]: type 1, range 32, base f5fd0000, size 11, enabled map[18]: type 1, range 32, base f5fc0000, size 13, enabled map[1c]: type 1, range 32, base f5f00000, size 19, enabled pcib0: matched entry for 0.4.INTB pcib0: slot 4 INTB hardwired to IRQ 17 found-> vendor=0x0e11, dev=0xb204, revid=0x01 bus=0, slot=4, func=2 class=08-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0197, statreg=0x0290, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=17 powerspec 2 supports D0 D3 current D0 found-> vendor=0x1166, dev=0x0201, revid=0x93 bus=0, slot=15, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x0147, statreg=0x2200, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 00002000, size 4, enabled found-> vendor=0x1166, dev=0x0212, revid=0x93 bus=0, slot=15, func=1 class=01-01-8a, hdrtype=0x00, mfdev=1 cmdreg=0x0145, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1166, dev=0x0225, revid=0x00 bus=0, slot=15, func=3 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0004, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1166, dev=0x0101, revid=0x05 bus=0, slot=16, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0142, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1166, dev=0x0101, revid=0x05 bus=0, slot=16, func=2 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0142, statreg=0x02b0, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1166, dev=0x0101, revid=0x05 bus=0, slot=17, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0142, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1166, dev=0x0101, revid=0x05 bus=0, slot=17, func=2 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0142, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) pci0: <display, VGA> at device 3.0 (no driver attached) pci0: <base peripheral> at device 4.0 (no driver attached) pci0: <base peripheral> at device 4.2 (no driver attached) isab0: <PCI-ISA bridge> at device 15.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <ServerWorks CSB5 UDMA100 controller> port 0x2000-0x200f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 15.1 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x2000 ata0: channel #0 on atapci0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=50 ostat1=01 ata0-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb ata0-slave: stat=0x00 err=0x24 lsb=0xff msb=0x00 ata0: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER> ata0: [MPSAFE] ata1: channel #1 on atapci0 atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=00 ostat0=ff ostat1=ff ata1: [MPSAFE] pcib1: <ACPI Host-PCI bridge> on acpi0 ACPI PCI link initial configuration: pci1: <ACPI PCI bus> on pcib1 pci1: physical bus=1 map[10]: type 1, range 64, base f79c0000, size 18, enabled map[18]: type 4, range 32, base 00003000, size 8, enabled map[1c]: type 3, range 64, base f78f0000, size 14, enabled pcib1: matched entry for 1.3.INTA pcib1: slot 3 INTA hardwired to IRQ 30 found-> vendor=0x0e11, dev=0xb178, revid=0x01 bus=1, slot=3, func=0 class=01-04-00, hdrtype=0x00, mfdev=0 cmdreg=0x0157, statreg=0x02b0, cachelnsz=16 (dwords) lattimer=0x47 (2130 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=30 powerspec 2 supports D0 D1 D3 current D0 MSI supports 2 messages, 64 bit ciss0: <Compaq Smart Array 5i> port 0x3000-0x30ff mem 0xf78f0000-0xf78f3fff,0xf79c0000-0xf79fffff irq 30 at device 3.0 on pci1 ciss0: Reserved 0x40000 bytes for rid 0x10 type 3 at 0xf79c0000 ciss0: [GIANT-LOCKED] ciss0: using 256 of 1024 available commands ciss0: firmware 2.58 ciss0: 2 SCSI channels ciss0: signature 'CISS' ciss0: valence 1 ciss0: supported I/O methods 0x6<simple,performant> ciss0: active I/O method 0x3<simple> ciss0: 4G page base 0x00000000 ciss0: interrupt coalesce delay 1000us ciss0: interrupt coalesce count 16 ciss0: max outstanding commands 1024 ciss0: bus types 0x2<ultra3> ciss0: server name '' ciss0: heartbeat 0x10000038 ciss0: 2 physical devices ciss0: 1 logical drive ciss0: logical drive (b0t0): RAID 0, 69120MB online pcib2: <ACPI Host-PCI bridge> on acpi0 ACPI PCI link initial configuration: pci2: <ACPI PCI bus> on pcib2 pci2: physical bus=2 map[10]: type 1, range 64, base f7af0000, size 16, enabled pcib2: matched entry for 2.1.INTA pcib2: slot 1 INTA hardwired to IRQ 29 found-> vendor=0x14e4, dev=0x16a7, revid=0x02 bus=2, slot=1, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0156, statreg=0x02b0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns) intpin=a, irq=29 powerspec 2 supports D0 D3 current D0 MSI supports 8 messages, 64 bit map[10]: type 1, range 64, base f7ae0000, size 16, enabled pcib2: matched entry for 2.2.INTA pcib2: slot 2 INTA hardwired to IRQ 31 found-> vendor=0x14e4, dev=0x16a7, revid=0x02 bus=2, slot=2, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0156, statreg=0x02b0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns) intpin=a, irq=31 powerspec 2 supports D0 D3 current D0 MSI supports 8 messages, 64 bit bge0: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem 0xf7af0000-0xf7afffff irq 29 at device 1.0 on pci2 bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xf7af0000 miibus0: <MII bus> on bge0 brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto bge0: bpf attached bge0: Ethernet address: 00:0f:20:6d:df:3d bge0: [MPSAFE] bge1: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem 0xf7ae0000-0xf7aeffff irq 31 at device 2.0 on pci2 bge1: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xf7ae0000 miibus1: <MII bus> on bge1 brgphy1: <BCM5703 10/100/1000baseTX PHY> on miibus1 brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto bge1: bpf attached bge1: Ethernet address: 00:0f:20:6d:df:3c bge1: [MPSAFE] pcib3: <ACPI Host-PCI bridge> on acpi0 ACPI PCI link initial configuration: pci3: <ACPI PCI bus> on pcib3 pci3: physical bus=3 pcib4: <ACPI Host-PCI bridge> on acpi0 ACPI PCI link initial configuration: pci6: <ACPI PCI bus> on pcib4 pci6: physical bus=6 map[10]: type 1, range 32, base f7c00000, size 22, enabled pcib4: matched entry for 6.2.INTA pcib4: slot 2 INTA hardwired to IRQ 26 found-> vendor=0x114f, dev=0x0004, revid=0x01 bus=6, slot=2, func=0 class=07-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0143, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=26 map[10]: type 1, range 32, base f7bf0000, size 12, enabled pcib4: matched entry for 6.30.INTA pcib4: slot 30 INTA hardwired to IRQ 18 found-> vendor=0x0e11, dev=0xa0f7, revid=0x14 bus=6, slot=30, func=0 class=08-04-00, hdrtype=0x00, mfdev=0 cmdreg=0x0142, statreg=0x0430, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=18 powerspec 2 supports D0 D3 current D0 MSI supports 1 message, 64 bit pci6: <simple comms> at device 2.0 (no driver attached) pci6: <base peripheral> at device 30.0 (no driver attached) atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 atkbd0: [GIANT-LOCKED] psm0: unable to allocate IRQ psmcpnp0 irq 12 on acpi0 psm0: current command byte:0065 psm0: failed to reset the aux device. sio0: irq maps: 0x1 0x11 0x1 0x1 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f5 irq 6 drq 2 on acpi0 fdc0: ic_type 90 part_id 73 fdc0: [MPSAFE] fdc0: [FAST] fd0: <1440-KB 3.5" drive> on fdc0 drive 0 ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it sio: sio0 already exists; skipping it Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 ex_isa_identify() unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed 0 unknown: status reg test failed ff sage repeated 2 times ahc_isa_probe 0: ioport 0xc00 alloc failed sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <ISA Option ROMs> at iomem 0xee000-0xeffff,0xc8000-0xcbfff,0xc0000-0xc7fff on isa0 pmtimer0 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fe0: not probed (disabled) ie0: not probed (disabled) lnc0: not probed (disabled) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) ppc0: parallel port not found. ppc0: <Parallel port> failed to probe at irq 7 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0x41 0x41 0x41 0x41 sio1: probe failed test(s): 0 1 2 4 6 7 9 sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. procfs registered Timecounter "TSC" frequency 2790957984 Hz quality 800 Timecounters tick every 10.000 msec lo0: bpf attached fdc0: output ready timeout sage repeated 6 times ata0-master: pio=0x0c wdma=0xffffffff udma=0xffffffff cable=40pin ata0-master: setting PIO4 on ServerWorks CSB5 chip acd0: <COMPAQ CD-ROM SN-124/N104> CDROM drive at ata0 as master acd0: read 4134KB/s (4134KB/s), 128KB buffer, PIO4 acd0: Reads: CDR, CDRW, CDDA stream, packet acd0: Writes: acd0: Audio: play, 255 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc fdc0: output ready timeout fdc0: input ready timeout fdc0: input ready timeout fdc0: output ready timeout fdc0: input ready timeout fdc0: input ready timeout fdc0: output ready timeout fdc0: input ready timeout fdc0: input ready timeout fdc0: output ready timeout fdc0: input ready timeout fdc0: input ready timeout ciss0: command status 0x1 (target status) scsi status 0x2 (probe0:ciss0:0:0:0): error 22 (probe0:ciss0:0:0:0): Unretryable Error ciss0: command status 0x1 (target status) scsi status 0x2 (probe0:ciss0:0:0:0): error 22 (probe0:ciss0:0:0:0): Unretryable Error pass0 at ciss0 bus 0 target 0 lun 0 pass0: <COMPAQ RAID 0 VOLUME OK> Fixed Direct Access SCSI-0 device pass0: 135.168MB/s transfers da0 at ciss0 bus 0 target 0 lun 0 da0: <COMPAQ RAID 0 VOLUME OK> Fixed Direct Access SCSI-0 device da0: 135.168MB/s transfers da0: 69459MB (142253280 512 byte sectors: 255H 32S/T 17433C) GEOM: new disk da0 ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0 ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0 ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0 ioapic0: routing intpin 8 (ISA IRQ 8) to cluster 0 ioapic0: routing intpin 9 (ISA IRQ 9) to cluster 0 ioapic0: routing intpin 13 (ISA IRQ 13) to cluster 0 ioapic0: routing intpin 14 (ISA IRQ 14) to cluster 0 ioapic0: routing intpin 15 (ISA IRQ 15) to cluster 0 ioapic1: routing intpin 13 (PCI IRQ 29) to cluster 0 ioapic1: routing intpin 14 (PCI IRQ 30) to cluster 0 ioapic1: routing intpin 15 (PCI IRQ 31) to cluster 0 [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/32 s:32 l:142253248 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure da0s1, start 16384 length 72833662976 end 72833679359 GEOM: Configure da0s1a, start 0 length 2147483648 end 2147483647 GEOM: Configure da0s1b, start 2147483648 length 2147483648 end 4294967295 GEOM: Configure da0s1c, start 0 length 72833662976 end 72833662975 GEOM: Configure da0s1d, start 4294967296 length 17179869184 end 21474836479 GEOM: Configure da0s1e, start 21474836480 length 42949672960 end 64424509439 Mounting root from ufs:/dev/da0s1a start_init: trying /sbin/init [following is result of "kldload digi" from my rc.local] pci0: driver added found-> vendor=0x1002, dev=0x4752, revid=0x27 bus=0, slot=3, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0087, statreg=0x0290, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D1 D2 D3 current D0 pci0:3:0: reprobing on driver added found-> vendor=0x0e11, dev=0xb203, revid=0x01 bus=0, slot=4, func=0 class=08-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0103, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=16 powerspec 2 supports D0 D3 current D0 pci0:4:0: reprobing on driver added pci0:4:0: Transition from D0 to D3 found-> vendor=0x0e11, dev=0xb204, revid=0x01 bus=0, slot=4, func=2 class=08-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0197, statreg=0x0290, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=17 powerspec 2 supports D0 D3 current D0 pci0:4:2: reprobing on driver added pci0:4:2: Transition from D0 to D3 pci1: driver added pci2: driver added pci3: driver added pci6: driver added found-> vendor=0x114f, dev=0x0004, revid=0x01 bus=6, slot=2, func=0 class=07-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0143, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=26 pci6:2:0: reprobing on driver added digi0 mem 0xf7c00000-0xf7ffffff irq 26 at device 2.0 on pci6 digi0: Reserved 0x400000 bytes for rid 0x10 type 3 at 0xf7c00000 digi0: Digiboard PCI PC/Xem ASIC, 16 ports found found-> vendor=0x0e11, dev=0xa0f7, revid=0x14 bus=6, slot=30, func=0 class=08-04-00, hdrtype=0x00, mfdev=0 cmdreg=0x0142, statreg=0x0430, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=18 powerspec 2 supports D0 D3 current D0 MSI supports 1 message, 64 bit pci6:30:0: reprobing on driver added pci6:30:0: Transition from D0 to D3 ppc0: parallel port not found. sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0x1c1 0x1c1 0x1c1 0x1c1 sio1: probe failed test(s): 0 1 2 4 6 7 9 >How-To-Repeat: Install 5.3-BETA6 from the i386 miniinstall image. System hangs at the reboot after the install is complete. >Fix: ENOCLUE >Release-Note: >Audit-Trail: >Unformatted:
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200410080853.i988rr5X032066>