Date: Fri, 15 Sep 2000 14:28:56 -0700 (PDT) From: Dennis Glatting <dennis.glatting@software-munitions.com> To: freebsd-stable@freebsd.org Subject: Problems with sa0 under STABLE Message-ID: <Pine.BSF.4.21.0009151427360.3272-100000@btw.plaintalk.bellevue.wa.us>
next in thread | raw e-mail | index | archive | help
I built a SMP kernel and attached an AIT drive. The kernel sees the drive
but I cannot access it. I don't understand this problem. Looks to me the
tape drive should be working. Below is the output of various commands.
Help would be appreciated.
Please reply directly as I am not subscribed to this list.
BTW, I can access the disk drive on the controller.
TIA
dmesg:
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1-STABLE #2: Fri Sep 15 13:49:22 PDT 2000
root@bugs:/usr/src/sys/compile/GRANNY
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (794.66-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,XMM>
real memory = 268034048 (261752K bytes)
avail memory = 256368640 (250360K bytes)
Changing APIC ID for IO APIC #0 from 0 to 2 on chip
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170020, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc041f000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI to PCI bridge (vendor=8086 device=250f)> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <NVidia Riva Ultra Vanta TNT2 graphics accelerator> at 0.0 irq 16
pcib2: <Intel 82801AA (ICH) Hub to PCI bridge> at device 30.0 on pci0
pci2: <PCI bus> on pcib2
ahc0: <Adaptec 29160N Ultra160 SCSI adapter> port 0xec00-0xecff mem 0xfafff000-0xfaffffff irq 16 at device 7.0 on pci2
ahc0: aic7892 Wide Channel A, SCSI Id=7, 16/255 SCBs
ahc1: <Adaptec 2940 Ultra SCSI adapter> port 0xe800-0xe8ff mem 0xfaffe000-0xfaffefff irq 17 at device 8.0 on pci2
ahc1: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xe480-0xe4ff mem 0xfaffdc00-0xfaffdc7f irq 18 at device 12.0 on pci2
xl0: Ethernet address: 00:b0:d0:24:97:8a
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <Intel 82801AA (ICH) PCI to LPC bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH ATA66 controller> port 0xffa0-0xffaf at device 31.1 on pci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82801AA (ICH) USB controller> port 0xff80-0xff9f irq 19 at device 31.2 on pci0
usb0: <Intel 82801AA (ICH) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <unknown card> (vendor=0x8086, dev=0x2413) at 31.3 irq 17
chip1: <Intel 82801AA (ICH) AC'97 Audio Controller> port 0xdc80-0xdcbf,0xd800-0xd8ff irq 17 at device 31.5 on pci0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
SMP: AP CPU #1 Launched!
acd0: CDROM <CRD-8482B> at ata1-master using PIO4
Waiting 15 seconds for SCSI devices to settle
sa0 at ahc1 bus 0 target 5 lun 0
sa0: <SONY SDX-300C 0300> Removable Sequential Access SCSI-2 device
sa0: 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
da0 at ahc0 bus 0 target 0 lun 0
da0: <FUJITSU MAJ3091MP 5508> Fixed Direct Access SCSI-4 device
da0: 80.000MB/s transfers (40.000MHz, offset 127, 16bit), Tagged Queueing Enabled
da0: 8683MB (17783239 512 byte sectors: 255H 63S/T 1106C)
da1 at ahc0 bus 0 target 1 lun 0
da1: <FUJITSU MAJ3091MP 5508> Fixed Direct Access SCSI-4 device
da1: 80.000MB/s transfers (40.000MHz, offset 127, 16bit), Tagged Queueing Enabled
da1: 8683MB (17783239 512 byte sectors: 255H 63S/T 1106C)
da2 at ahc1 bus 0 target 2 lun 0
da2: <SEAGATE ST39140W 1281> Fixed Direct Access SCSI-2 device
da2: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da2: 8683MB (17783240 512 byte sectors: 64H 32S/T 8683C)
Mounting root from ufs:/dev/da0s1a
some actions:
bugs: camcontrol devlist
<FUJITSU MAJ3091MP 5508> at scbus0 target 0 lun 0 (pass0,da0)
<FUJITSU MAJ3091MP 5508> at scbus0 target 1 lun 0 (pass1,da1)
<SEAGATE ST39140W 1281> at scbus1 target 2 lun 0 (pass2,da2)
<SONY SDX-300C 0300> at scbus1 target 5 lun 0 (pass3,sa0)
bugs# camcontrol inquiry sa0
pass3: <SONY SDX-300C 0300> Removable Sequential Access SCSI-2 device
pass3: 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
bugs# camcontrol periphlist sa0
pass3: generation: 4 index: 1 status: MORE
sa0: generation: 4 index: 2 status: LAST
bugs# tar tvf /dev/sa0
tar: can't open /dev/sa0 : Device not configured
bugs# tar tvf /dev/rsa0
tar: can't open /dev/rsa0 : Device not configured
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.21.0009151427360.3272-100000>