Date: Thu, 21 Oct 2004 19:08:52 -0700 (PDT) From: Doug White <dwhite@gumbysoft.com> To: luke@prgmr.com Cc: stable@freebsd.org Subject: Re: FreeBSD 4.10 + PAE + SunFire v40z (Newisys 4100) Message-ID: <20041021184743.G41366@carver.gumbysoft.com> In-Reply-To: <20041020125520.P29221@prgmr.com> References: <20041020125520.P29221@prgmr.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Wed, 20 Oct 2004 luke@prgmr.com wrote: > > I have this SunFire v40z (as far as I can tell, it is a rebadged > Newisys 4100. Sopposedly, sun manufactured it, but I can't find any > difference between it and the specs for the 4100) for testing- 4 CPUs, > 8G ram, seperate 'service' processor that acts as a serial server and > remote rebooter. So far, it looks very nice, save for one problem. > I can not boot a PAE kernel off the onboard SCSI. A rather large problem. > > I have the box netbooting right now. It works fine, save for the LSILogic > SCSI. Why are you running this in i386 mode? Running an opteron in i386 mode + PAE is a waste of a perfectly good 64 bit box :) > mpt0: <LSILogic 1030 Ultra4 Adapter> port 0x2000-0x20ff mem \ > 0xe5820000-0xe582fff f,0xe5830000-0xe583ffff irq 19 at device 4.0 on pci2 > mpt0: error 16 creating per-cmd DMA maps > mpt0: Could not allocate DMA memory 16 is EBUSY, whicih makes no sense whatsoever because it never sets error to EBUSY. It would only ever set it to ENOMEM or succeed. I suspect nasty bad memory corruption. Can the mpt device probe correctly if you drop it below 4GB? > > > > > %uname -a > FreeBSD 4.10-RELEASE FreeBSD 4.10-RELEASE #0: Wed Oct 20 12:11:08 PDT > 2004 luke@:/usr/obj/usr/src/sys/SMP_PAE i386 > > > full dmesg from the successful netboot follows: > > Copyright (c) 1992-2004 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 4.10-RELEASE #0: Wed Oct 20 12:11:08 PDT 2004 > luke@:/usr/obj/usr/src/sys/SMP_PAE > Timecounter "i8254" frequency 1193182 Hz > CPU: AMD Opteron(tm) Processor 848 (2189.08-MHz 686-class CPU) > Origin = "AuthenticAMD" Id = 0xf5a Stepping = 10 > > Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,\ > CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2> > AMD Features=0xe0500000<<b20>,AMIE,<b29>,DSP,3DNow!> > real memory = 8589934592 (8388608K bytes) > avail memory = 7898091520 (7712980K bytes) > Programming 24 pins in IOAPIC #0 > IOAPIC #0 intpin 2 -> irq 0 > Programming 4 pins in IOAPIC #1 > Programming 4 pins in IOAPIC #2 > Programming 4 pins in IOAPIC #3 > Programming 4 pins in IOAPIC #4 > Programming 4 pins in IOAPIC #5 > Programming 4 pins in IOAPIC #6 > FreeBSD/SMP: Multiprocessor motherboard: 4 CPUs > cpu0 (BSP): apic id: 0, version: 0x00040010, at 0xfee00000 > cpu1 (AP): apic id: 1, version: 0x00040010, at 0xfee00000 > cpu2 (AP): apic id: 2, version: 0x00040010, at 0xfee00000 > cpu3 (AP): apic id: 3, version: 0x00040010, at 0xfee00000 > io0 (APIC): apic id: 4, version: 0x00170011, at 0xfec00000 > io1 (APIC): apic id: 5, version: 0x00030011, at 0xe4000000 > io2 (APIC): apic id: 6, version: 0x00030011, at 0xe4001000 > io3 (APIC): apic id: 7, version: 0x00030011, at 0xe5b01000 > io4 (APIC): apic id: 8, version: 0x00030011, at 0xe5b03000 > io5 (APIC): apic id: 9, version: 0x00030011, at 0xe5b05000 > io6 (APIC): apic id: 10, version: 0x00030011, at 0xe5b07000 > Preloaded elf kernel "kernel" at 0xc053f000. > Pentium Pro MTRR support enabled > md0: Malloc disk > Using $PIR table, 24 entries at 0xc00fde40 > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcib0: <Host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > pcib16: <PCI to PCI bridge (vendor=1022 device=7460)> at device 6.0 on > pci0 > IOAPIC #0 intpin 19 -> irq 2 > IOAPIC #0 intpin 17 -> irq 16 > pci1: <PCI bus> on pcib16 > ohci0: <OHCI (generic) USB controller> mem 0xe4120000-0xe4120fff irq 2 at\ > device 0.0 on pci1 > usb0: OHCI version 1.0, legacy support > usb0: SMM does not respond, resetting > usb0: <OHCI (generic) USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 3 ports with 3 removable, self powered > ohci1: <OHCI (generic) USB controller> mem 0xe4121000-0xe4121fff irq 2 at\ > device 0.1 on pci1 > usb1: OHCI version 1.0, legacy support > usb1: SMM does not respond, resetting > usb1: <OHCI (generic) USB controller> on ohci1 > usb1: USB revision 1.0 > uhub1: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 3 ports with 3 removable, self powered > pci1: <Trident model 9880 VGA-compatible display device> at 5.0 irq 16 > isab0: <PCI to ISA bridge (vendor=1022 device=7468)> at device 7.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <AMD 8111 ATA133 controller> port 0x1000-0x100f at device 7.1 on\ > pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > chip0: <PCI to Other bridge (vendor=1022 device=746b)> at device 7.3 on\ > pci0 > pcib17: <PCI to PCI bridge (vendor=1022 device=7450)> at device 10.0 on\ > pci0 > IOAPIC #1 intpin 1 -> irq 17 > IOAPIC #1 intpin 2 -> irq 18 > IOAPIC #1 intpin 3 -> irq 19 > pci2: <PCI bus> on pcib17 > bge0: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem\ > 0xe5800000-0xe580ffff irq 17 at device 2.0 on pci2 > bge0: Ethernet address: 00:09:3d:00:48:c3 > miibus0: <MII bus> on bge0 > brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0 > brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, \ > 1000baseTX-FDX, auto > bge1: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem\ > 0xe5810000-0xe581ffff irq 18 at device 3.0 on pci2 > bge1: Ethernet address: 00:09:3d:00:4b:e3 > miibus1: <MII bus> on bge1 > brgphy1: <BCM5703 10/100/1000baseTX PHY> on miibus1 > brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, \ > 1000baseTX-FDX, auto > mpt0: <LSILogic 1030 Ultra4 Adapter> port 0x2000-0x20ff mem \ > 0xe5820000-0xe582ffff,0xe5830000-0xe583ffff irq 19 at device 4.0 on pci2 > mpt0: error 16 creating per-cmd DMA maps > mpt0: Could not allocate DMA memory > pci0: <unknown card> (vendor=0x1022, dev=0x7451) at 10.1 > pcib18: <PCI to PCI bridge (vendor=1022 device=7450)> at device 11.0 on > pci0 > pci3: <PCI bus> on pcib18 > pci0: <unknown card> (vendor=0x1022, dev=0x7451) at 11.1 > pcib1: <Host to PCI bridge> on motherboard > pci4: <PCI bus> on pcib1 > pcib2: <Host to PCI bridge> on motherboard > pci5: <PCI bus> on pcib2 > pcib3: <Host to PCI bridge> on motherboard > pci6: <PCI bus> on pcib3 > pcib4: <Host to PCI bridge> on motherboard > pci7: <PCI bus> on pcib4 > pcib5: <Host to PCI bridge> on motherboard > pci8: <PCI bus> on pcib5 > pcib6: <Host to PCI bridge> on motherboard > pci9: <PCI bus> on pcib6 > pcib7: <Host to PCI bridge> on motherboard > pci10: <PCI bus> on pcib7 > pcib8: <Host to PCI bridge> on motherboard > pci11: <PCI bus> on pcib8 > pcib9: <Host to PCI bridge> on motherboard > pci12: <PCI bus> on pcib9 > pcib10: <Host to PCI bridge> on motherboard > pci13: <PCI bus> on pcib10 > pcib11: <Host to PCI bridge> on motherboard > pci14: <PCI bus> on pcib11 > pcib12: <Host to PCI bridge> on motherboard > pci15: <PCI bus> on pcib12 > pcib13: <Host to PCI bridge> on motherboard > pci16: <PCI bus> on pcib13 > pcib14: <Host to PCI bridge> on motherboard > pci17: <PCI bus> on pcib14 > pcib15: <Host to PCI bridge> on motherboard > pci18: <PCI bus> on pcib15 > orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc97ff,0xc9800-0xcafff,\ > 0xcb000-0xcb7ff on isa0 > pmtimer0 on isa0 > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model Generic PS/2 mouse, device ID 0 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1 at port 0x2f8-0x2ff irq 3 on isa0 > sio1: type 16550A > ppc0: parallel port not found. > APIC_IO: Testing 8254 interrupt delivery > APIC_IO: routing 8254 via IOAPIC #0 intpin 2 > SMP: AP CPU #1 Launched! > SMP: AP CPU #2 Launched! > SMP: AP CPU #3 Launched! > acd0: DVD-ROM <DV-28E-C> at ata1-master PIO4 > NFS ROOT: 10.1.0.1:/home/system/wc/FreeBSD_4_10_test_sandbox/ > bge0: gigabit link up > > _______________________________________________ > freebsd-stable@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-stable > To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org" > -- Doug White | FreeBSD: The Power to Serve dwhite@gumbysoft.com | www.FreeBSD.org
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20041021184743.G41366>