Date: Wed, 9 Jan 2002 22:43:39 -0600 From: Marius Strom <marius@marius.org> To: "M. Warner Losh" <imp@village.org> Cc: freebsd@samurai.deec.uc.pt, stable@FreeBSD.ORG, paulo@isr.uc.pt, mobile@FreeBSD.ORG Subject: Re: Can't boot FreeBSD on a Toshiba Laptop Message-ID: <20020110044338.GM64900@marius.org> In-Reply-To: <20020109213535.GL64900@marius.org> References: <Pine.BSF.4.21.0201091439420.782-300000@samurai.deec.uc.pt> <20020109.115326.99747006.imp@village.org> <20020109213535.GL64900@marius.org>
next in thread | previous in thread | raw e-mail | index | archive | help
Yet another data point: Doesn't work with 4.5-RC1 either. CC:ing'g -mobile, and setting reply-to to mobile since -stable is in codefreeze. On Wed, Jan 09, 2002 at 03:35:35PM -0600, Marius Strom wrote: > Warner (et al), > Unfortunately, still doesn't work. > > Last few lines of boot: > > pci2: <unknown card> (vendor=0x1179, dev=0x0804) at 6.0 irq 5 > isab0: <PCI to ISA bridge (vendor=8086 device=248c)> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Generic PCI ATA controller> port 0x1860-0x186f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 mem 0xd0000000-0xd00003ff at device 31.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > pci0: <unknown card> (vendor=0x8086, dev=0x2483) at 31.3 irq 10 > pci0: <unknown card> (vendor=0x8086, dev=0x2485) at 31.5 irq 10 > pci0: <unknown card> (vendor=0x8086, dev=0x2486) at 31.6 irq 10 > > > It hard locks at that point. If I can provide any information obtainable > from another OS on the machine (it boots linux, winxp) let me know (I can > also dig in and find exactly what components are where). > > Here's what I do know: > > Video card in the system is a GeForce 2 Go (their mobile GeFoce). > RealTek chipset is detected > USB is detected > pcic stuff (TI PCI-1420 PCI-CardBus Bridge) is detected. Config Reg: > [speaker enable][pwr save][FUNC pci int + CSC serial isa irq] > > According to WinXP, the PCI device on IRQ10 is a Intel 82801CA/CAM SMBus > Controller - 2483. WinXP shows nothing on IRQ5. > IRQ3 is the SMC IrCC Infrared port. Anyway to make FreeBSD think of this > as a serial interface to do debug kernels? > IRQ9 is shared between the Realtek Card, Crystal WDM Audi card, GeForce2, > USB controller, TI IEEE1394 controller, TI PCMCIA controller, Toshiba AMR > Software Modem, and Toshiba SM Host Controller. > > Again, if you need any more info, let me know and I'll see what I can dig > up. I know I'd be very interested in seeing FreeBSD supported on this > laptop. > > On Wed, Jan 09, 2002 at 11:53:26AM -0700, M. Warner Losh wrote: > > OK. This is a longshot (since you said that 4.3 also failed), but can > > you try a 4.4 or newer kernel and in the boot loader say: > > hw.pcic.intr_path=1 > > hw.pcic.irq=0 > > Warner > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > with "unsubscribe freebsd-stable" in the body of the message > > -- > /-------------------------------------------------> > Marius Strom | Always carry a short length of fibre-optic cable. > Professional Geek | If you get lost, then you can drop it on the > System/Network Admin | ground, wait 10 minutes, and ask the backhoe > http://www.marius.org/ | operator how to get back to civilization. > \-------------| Alan Frame |----------------------> > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-stable" in the body of the message -- /-------------------------------------------------> Marius Strom | Always carry a short length of fibre-optic cable. Professional Geek | If you get lost, then you can drop it on the System/Network Admin | ground, wait 10 minutes, and ask the backhoe http://www.marius.org/ | operator how to get back to civilization. \-------------| Alan Frame |----------------------> To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020110044338.GM64900>