Date: Sun, 8 Jun 2008 10:47:22 +0900 From: Pyun YongHyeon <pyunyh@gmail.com> To: Norikatsu Shigemura <nork@FreeBSD.org> Cc: freebsd-current@FreeBSD.org Subject: Re: Call for testers: re(4) and RTL8168C/RTL8168CP/RTL8111C/RTL8111CP Message-ID: <20080608014722.GB8825@cdnetworks.co.kr> In-Reply-To: <20080607155215.9cb0a863.nork@FreeBSD.org> References: <20080607035911.GD4565@cdnetworks.co.kr> <20080607155215.9cb0a863.nork@FreeBSD.org>
next in thread | previous in thread | raw e-mail | index | archive | help
On Sat, Jun 07, 2008 at 03:52:15PM +0900, Norikatsu Shigemura wrote: > On Sat, 7 Jun 2008 12:59:11 +0900 > Pyun YongHyeon <pyunyh@gmail.com> wrote: > > I don't have any of these hardwares so if you have one of these > > hardwares please give it try and let me know how it goes. Some > > users reported success but I'd like to get more feedback because > > re(4) supports too many variants and I don't like to break supports > > for old RealTek hardwares. > > Wow!! Quite Good Works my RTL8169SBL (cardbus). I confirmed > following operations: > > (ok) probe&attach > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > re0: <RealTek 8169/8169S/8169SB(L)/8110S/8110SB(L) Gigabit Ethernet> port 0x3100-0x31ff mem 0xb0103000-0xb01031ff irq 22 at device 0.0 on cardbus0 > re0: Chip rev. 0x10000000 > re0: MAC rev. 0x00000000 > miibus1: <MII bus> on re0 > rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus1 > rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto > re0: Ethernet address: 00:e0:4c:77:ab:e8 > re0: [FILTER] > re0: link state changed to DOWN > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > > (ok) ifconfig re0 (w/o cable disconnect) > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > re0: flags=8843<BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=399b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_UCAST,WOL_MCAST,WOL_MAGIC> > ether 00:e0:4c:77:ab:e8 > media: Ethernet autoselect (none) > status: no carrier > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > > (ok) cable connected > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > re0: link state changed to UP > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > > (ok) dhclient re0 > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=399b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_UCAST,WOL_MCAST,WOL_MAGIC> > ether 00:e0:4c:77:ab:e8 > inet 192.168.XXX.XXX netmask 0xffffff00 broadcast 192.168.XXX.255 > media: Ethernet autoselect (100baseTX <full-duplex>) > status: active > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > > (ok) plug&pray > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > rgephy0: detached > miibus1: detached > re0: detached > cardbus0: Expecting link target, got 0x0 > re0: <RealTek 8169/8169S/8169SB(L)/8110S/8110SB(L) Gigabit Ethernet> port 0x3100-0x31ff mem 0xb0103000-0xb01031ff irq 22 at device 0.0 on cardbus0 > re0: Chip rev. 0x10000000 > re0: MAC rev. 0x00000000 > miibus1: <MII bus> on re0 > rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus1 > rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto > re0: Ethernet address: 00:e0:4c:77:ab:e8 > re0: [FILTER] > re0: link state changed to DOWN > re0: link state changed to UP > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > > Of course, no panic!! Thank you!! Thanks for reporting. -- Regards, Pyun YongHyeon
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20080608014722.GB8825>