Date: Thu, 30 Jan 2003 20:33:33 -0600 From: Josh Tolbert <hemi@just.puresimplicity.net> To: Bernd Walter <ticso@cicely8.cicely.de>, freebsd-alpha@FreeBSD.org Subject: Re: Unusual SCSI problem... Message-ID: <20030131023333.GA7512@just.puresimplicity.net> In-Reply-To: <20030131014526.GE38062@cicely8.cicely.de> References: <20030125055014.GA86967@just.puresimplicity.net> <20030131014541.GB7260@just.puresimplicity.net> <20030131014526.GE38062@cicely8.cicely.de>
index | next in thread | previous in thread | raw e-mail
[-- Attachment #1 --] Hi Bernd, On Fri, Jan 31, 2003 at 02:45:27AM +0100, Bernd Walter wrote: > On Thu, Jan 30, 2003 at 07:45:42PM -0600, Josh Tolbert wrote: > > I've got a PC164LX, 533MHz 21164A and 1G RAM. I'm trying > > to use a Symbios/LSI Logic SYM22910 dual-channel, U2W SCSI controller > > with various hard drives. With some drives (specifically IBM > > DDYS-34560 UW drives) everything appears to function just fine, > > However, with other drives the controller and SRM see the drive, > > but exer_werite on the drive doesn't work and FreeBSD doesn't see > > the drive. During boot of the 5.0 miniinst CD I get (noperiph:sym0:-1:-1) > > or something of the sort for both channels after the "waiting 15 > > seconds for SCSI devices" message appears. > > > > Some wise Alpha people (in #Alpha on freenode; #FreeBSD-alpha > > seems to be fairly empty a lot of the time) advised me to "chmod > > +w dka300.3.0.6.0", which worked fine and gave me no errors. At > > that point I was able to "exer -a w dka300" just fine, as well as > > exer_write the drive, but FreeBSD's dmesg still didn't show a drive > > present. > > This is only required, if the drive is probed correctly, but sysinstall > doesn't show it. > What does boot -v say? > > -- > B.Walter COSMO-Project http://www.cosmo-project.de > ticso@cicely.de Usergroup info@cosmo-project.de > I've included the dmesg output from the machine in dmesg-alpha.txt. The drive shows up fine, but I can't disklabel the drive. dd seems to write to the drive ok, but otherwise nothing. Any advice? Thanks, Josh [-- Attachment #2 --] Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.0-RELEASE #0: Fri Jan 17 01:14:51 GMT 2003 root@mithlond.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xfffffc0000842000. EB164 Digital AlphaPC 164LX 533 MHz, 531MHz 8192 byte page size, 1 processor. CPU: EV56 (21164A) major=7 minor=2 extensions=0x1<BWX> OSF PAL rev: 0x1000200020117 real memory = 1071554560 (1021 MB) Physical memory chunk(s): 0x00864000 - 0x3ffe1fff, 1064820736 bytes (129983 pages) avail memory = 1034829824 (986 MB) Initializing GEOMetry subsystem random: <entropy source> null: <null device, zero device> mem: <memory & I/O> cia0: <2117x Core Logic chipset> cia0: Pyxis, pass 1 cia0: extended capabilities: 1<BWEN> pcib0: <2117x PCI host bus adapter> on cia0 pci0: <PCI bus> on pcib0 pci0: physical bus=0 map[10]: type 1, range 32, base 82000000, size 25, enabled map[14]: type 3, range 32, base 88000000, size 25, enabled map[18]: type 4, range 32, base 00001000, size 8, enabled found-> vendor=0x121a, dev=0x0005, revid=0x01 bus=0, slot=5, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0003, statreg=0x8090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=2 powerspec 1 supports D0 D3 current D0 map[10]: type 4, range 32, base 00001100, size 8, enabled map[14]: type 1, range 64, base 84255000, size 10, enabled map[1c]: type 1, range 64, base 84250000, size 13, enabled found-> vendor=0x1000, dev=0x000b, revid=0x05 bus=0, slot=6, func=0 class=01-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x11 (4250 ns), maxlat=0x40 (16000 ns) intpin=a, irq=0 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 4, range 32, base 00001200, size 8, enabled map[14]: type 1, range 64, base 84255400, size 10, enabled map[1c]: type 1, range 64, base 84252000, size 13, enabled found-> vendor=0x1000, dev=0x000b, revid=0x05 bus=0, slot=6, func=1 class=01-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x11 (4250 ns), maxlat=0x40 (16000 ns) intpin=b, irq=7 powerspec 2 supports D0 D1 D2 D3 current D0 found-> vendor=0x8086, dev=0x0484, revid=0x43 bus=0, slot=8, func=0 class=00-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 3, range 32, base 84254000, size 12, enabled map[14]: type 4, range 32, base 00001300, size 5, enabled map[18]: type 1, range 32, base 84000000, size 20, enabled found-> vendor=0x8086, dev=0x1229, revid=0x02 bus=0, slot=9, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns) intpin=a, irq=3 map[20]: type 4, range 32, base 00001330, size 4, enabled found-> vendor=0x1095, dev=0x0646, revid=0x01 bus=0, slot=11, func=0 class=01-01-80, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns) intpin=a, irq=5 pci0: <display, VGA> at device 5.0 (no driver attached) sym0: <896> port 0x1100-0x11ff mem 0x84250000-0x84251fff,0x84255000-0x842553ff irq 0 at device 6.0 on pci0 sym0: Delay (GEN=11): 243 msec, 36577 KHz sym0: Delay (GEN=11): 220 msec, 40401 KHz sym0: Delay (GEN=11): 220 msec, 40401 KHz sym0: chip clock is 40401KHz sym0: clock multiplier assumed sym0: Symbios NVRAM, ID 7, Fast-40, SE, parity checking sym0: open drain IRQ line driver, using on-chip SRAM sym0: using LOAD/STORE-based firmware. sym0: handling phase mismatch from SCRIPTS. sym0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 00/00/00/00/00/00 sym0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 07/4e/80/01/08/24 sym0: Delay (GEN=11): 253 msec, 35131 KHz sym0: Delay (GEN=11): 264 msec, 33667 KHz sym0: Delay (GEN=11): 265 msec, 33540 KHz sym0: interrupting at CIA irq 0 sym0: enabling clock multiplier sym0: Downloading SCSI SCRIPTS. sym1: <896> port 0x1200-0x12ff mem 0x84252000-0x84253fff,0x84255400-0x842557ff irq 7 at device 6.1 on pci0 sym1: Delay (GEN=11): 243 msec, 36577 KHz sym1: Delay (GEN=11): 220 msec, 40401 KHz sym1: Delay (GEN=11): 220 msec, 40401 KHz sym1: chip clock is 40401KHz sym1: clock multiplier assumed sym1: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking sym1: open drain IRQ line driver, using on-chip SRAM sym1: using LOAD/STORE-based firmware. sym1: handling phase mismatch from SCRIPTS. sym1: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 00/00/00/00/00/00 sym1: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 07/4e/80/01/08/24 sym1: Delay (GEN=11): 253 msec, 35131 KHz sym1: Delay (GEN=11): 264 msec, 33667 KHz sym1: Delay (GEN=11): 265 msec, 33540 KHz sym1: interrupting at CIA irq 7 sym1: enabling clock multiplier sym1: Downloading SCSI SCRIPTS. PCI-ISA bridge with incorrect subclass 0x0 PCI-ISA bridge with incorrect subclass 0x0 isab0: <PCI-ISA bridge> at device 8.0 on pci0 isa0: <ISA bus> on isab0 fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x1300-0x131f mem 0x84000000-0x840fffff,0x84254000-0x84254fff irq 3 at device 9.0 on pci0 fxp0: using memory space register mapping fxp0: interrupting at CIA irq 3 fxp0: Ethernet address 00:90:27:3c:c1:c6 fxp0: PCI IDs: 8086 1229 8086 0001 0002 fxp0: Dynamic Standby mode is disabled inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: bpf attached atapci0: <CMD 646 ATA controller> port 0x1330-0x133f irq 5 at device 11.0 on pci0 ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1330 ata0: mask=01 ostat0=00 ostat2=ff ata0-master: ATAPI 14 eb ata0: mask=01 stat0=00 stat1=00 ata0: devices=04 ata0: at 0x1f0 irq 14 on atapci0 ata0: interrupting at ISA irq 14 ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1338 ata1: at 0x170 irq 15 on atapci0 ata1: interrupting at ISA irq 15 ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it Trying Read_Port at 203 CTL0001: start dependent (0) CTL0001: adding irq mask 0x20 CTL0001: adding dma mask 0x2 CTL0001: adding dma mask 0x20 CTL0001: adding io range 0x220-0x22f, size=0x10, align=0x1 CTL0001: adding io range 0x330-0x331, size=0x2, align=0x1 CTL0001: adding io range 0x388-0x38b, size=0x4, align=0x1 CTL0001: start dependent (1) CTL0001: adding irq mask 0x6a0 CTL0001: adding dma mask 0xa CTL0001: adding dma mask 0xa0 CTL0001: adding io range 0x220-0x28f, size=0x10, align=0x20 CTL0001: adding io range 0x300-0x331, size=0x2, align=0x30 CTL0001: adding io range 0x388-0x38b, size=0x4, align=0x1 CTL0001: start dependent (1) CTL0001: adding irq mask 0x6a0 CTL0001: adding dma mask 0xa CTL0001: adding dma mask 0xa0 CTL0001: adding io range 0x220-0x28f, size=0x10, align=0x20 CTL0001: adding io range 0x300-0x331, size=0x2, align=0x30 CTL0001: start dependent (2) CTL0001: adding irq mask 0x6a0 CTL0001: adding dma mask 0xa CTL0001: adding dma mask 0xa0 CTL0001: adding io range 0x220-0x28f, size=0x10, align=0x20 CTL0001: start dependent (2) CTL0001: adding irq mask 0x6a0 CTL0001: adding dma mask 0xa CTL0001: adding io range 0x220-0x28f, size=0x10, align=0x20 CTL0001: adding io range 0x300-0x331, size=0x2, align=0x30 CTL0001: adding io range 0x388-0x38b, size=0x4, align=0x1 CTL0001: start dependent (2) CTL0001: adding irq mask 0x6a0 CTL0001: adding dma mask 0xa CTL0001: adding io range 0x220-0x28f, size=0x10, align=0x20 CTL0001: end dependent CTL7001: adding io range 0x200-0x207, size=0x8, align=0x1 sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0003 atkbd: keyboard ID 0x83ab (2) kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 atkbd0: interrupting at ISA irq 1 psm0: current command byte:0043 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: interrupting at ISA irq 12 psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons psm0: config:00000000, flags:00000000, packet size:3 psm0: syncmask:c0, syncbits:00 fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0 fdc0: interrupting at ISA irq 6 mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0 Calibrating clock(s) ... PCC clock: 533185149 Hz (firmware 531914893 Hz) i8254 clock: 1192016 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency ppc0: using extended I/O port range ppc0: EPP SPP ppc0: <Parallel port> at port 0x3bc-0x3c3 irq 7 on isa0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode lpt0: <Printer> on ppbus0 lpt0: Polled port ppi0: <Parallel I/O> on ppbus0 ppc0: interrupting at ISA irq 7 sc0: <System console> on isa0 sc0: VGA <16 virtual consoles, flags=0x200> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio0: irq maps: 0x21 0x31 0x21 0x21 sio0 at port 0x3f8-0x3ff irq 4 on isa0 sio0: type 16550A sio0: interrupting at ISA irq 4 sio1: irq maps: 0x21 0x29 0x21 0x21 sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A sio1: interrupting at ISA irq 3 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xb8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39 3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 EGA/VGA parameters to be used for mode 24 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39 3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff isa_probe_children: probing PnP devices unknown: <Audio> failed to probe at port 0x388-0x38b,0x330-0x331,0x220-0x22f irq 5 drq 5,1 on isa0 unknown: <Game> failed to probe at port 0x200-0x207 on isa0 procfs registered Timecounter "i8254" frequency 1193182 Hz Timecounter "alpha" frequency 533185149 Hz Timecounters tick every 0.976 msec lo0: bpf attached ata0-master: piomode=4 dmamode=2 udmamode=-1 dmaflag=1 ata0-master: success setting PIO4 on generic chip acd0: <CREATIVECD4820E/1.03> CDROM drive at ata0 as master acd0: read 2755KB/s (3021KB/s), 240KB buffer, PIO4 acd0: Reads: CD-R, CD-RW, CD-DA stream acd0: Writes: acd0: Audio: play, 255 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: CD-ROM 120mm data disc Waiting 15 seconds for SCSI devices to settle (noperiph:sym0:0:-1:-1): SCSI BUS reset delivered. sym0: enabling clock multiplier sym0: Downloading SCSI SCRIPTS. (noperiph:sym1:0:-1:-1): SCSI BUS reset delivered. sym1: enabling clock multiplier sym1: Downloading SCSI SCRIPTS. (probe0:sym0:0:0:0): Retrying Command (probe3:sym0:0:3:0): Retrying Command pass0 at sym0 bus 0 target 0 lun 0 pass0: <IBM DDRS-34560W S92A> Fixed Direct Access SCSI-2 device pass0: Serial Number RD0G9589 pass0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled pass1 at sym0 bus 0 target 3 lun 0 pass1: <SEAGATE ST318203LW 0002> Fixed Direct Access SCSI-2 device pass1: Serial Number LR8602750000102347N0 pass1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled da1 at sym0 bus 0 target 3 lun 0 da1: <SEAGATE ST318203LW 0002> Fixed Direct Access SCSI-2 device da1: Serial Number LR8602750000102347N0 da1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled da1: 17366MB (35566480 512 byte sectors: 255H 63S/T 2213C) GEOM: new disk da0 GEOM: new disk da1 da0 at sym0 bus 0 target 0 lun 0 da0: <IBM DDRS-34560W S92A> Fixed Direct Access SCSI-2 device da0: Serial Number RD0G9589 da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled da0: 4357MB (8925000 512 byte sectors: 255H 63S/T 555C) GEOM: Add da0 hot[0] start 64 length 276 end 339 GEOM: Configure da0a, start 0 length 268435456 end 268435455 GEOM: Configure da0b, start 268435456 length 2143109120 end 2411544575 GEOM: Configure da0c, start 0 length 4569600000 end 4569599999 GEOM: Configure da0d, start 2411544576 length 268435456 end 2679980031 GEOM: Configure da0e, start 2679980032 length 268435456 end 2948415487 GEOM: Configure da0f, start 2948415488 length 1621184512 end 4569599999 Mounting root from ufs:/dev/da0a start_init: trying /sbin/inithome | help
Want to link to this message? Use this
URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20030131023333.GA7512>