Date: Mon, 2 Mar 2009 15:17:06 -0300 (BRT) From: "Nenhum_de_Nos" <matheus@eternamente.info> To: "Hans Petter Selasky" <hselasky@c2i.net> Cc: freebsd-current@freebsd.org Subject: Re: problem on usb boot from mini itx Message-ID: <044a92c96375670511fc437d6b924923.squirrel@cygnus.homeunix.com> In-Reply-To: <200903021614.24159.hselasky@c2i.net> References: <f8161e633a32c1fcde0661afb816cbcb.squirrel@cygnus.homeunix.com> <200903021453.44367.hselasky@c2i.net> <ff4fd5b822337d287c8ca9f79b2f3968.squirrel@cygnus.homeunix.com> <200903021614.24159.hselasky@c2i.net>
next in thread | previous in thread | raw e-mail | index | archive | help
On Mon, March 2, 2009 12:14, Hans Petter Selasky wrote: > On Monday 02 March 2009, Nenhum_de_Nos wrote: >> On Mon, March 2, 2009 10:53, Hans Petter Selasky wrote: >> > On Monday 02 March 2009, Nenhum_de_Nos wrote: >> >> hail, >> >> >> >> I'm trying to make a router from a mini itx, but can't get it to boot >> >> from >> >> usb disk or stick. I can boot from usb cdrom and install ok, 7.1 and >> >> 7.0. >> >> but when I try to boot, I get to the point: >> >> >> >> F1 FreeBSD >> >> >> >> and press enter. >> >> >> >> then I get: >> >> Can't work out which disk we are booting from. >> >> Guessed BIOS device 0x80 not found by probes, defaulting to disk0: >> >> >> >> can't load 'kernel' >> >> >> >> Type '?' for a list of commands, 'help' for more detailed help. >> >> OK >> >> >> >> lsdev gives me: >> >> >> >> cd devices: >> >> disk devices: >> >> pxe devices: >> >> >> >> so, I got to the point it can't find my usb disk, but I don't know >> why >> >> as >> >> in boot cd it says the disk0 ok. so I copied all cd boot stuff >> >> (boot/cdboot/etc) to see if I can use that to again see my disk, but >> I >> >> got >> >> nowhere :( >> >> >> >> I used the usb disk on other pc and all went fine, even compiled >> current >> >> (my target branch) to see if most recent usb boot things (read some >> from >> >> two threads here, not got deep though) and also nothing :( >> >> >> >> is there anything I can do ? >> >> >> >> dmesg follows >> >> >> >> thanks, >> >> >> >> matheus >> >> >> >> the dmesg: >> >> >> >> Copyright (c) 1992-2009 The FreeBSD Project. >> >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, >> 1994 >> >> The Regents of the University of California. All rights reserved. >> >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> >> FreeBSD 8.0-CURRENT #0: Sun Mar 1 22:52:45 BRT 2009 >> >> root@cygnus.apartnet:/usr/obj/usr/src/sys/Cygnus8 >> >> Timecounter "i8254" frequency 1193182 Hz quality 0 >> >> CPU: Transmeta(tm) Crusoe(tm) Processor TM5700 (798.13-MHz 586-class >> >> CPU) >> >> Origin = "GenuineTMx86" Id = 0x543 Stepping = 3 >> >> Features=0x84893f<FPU,VME,DE,PSE,TSC,MSR,CX8,SEP,CMOV,PN,MMX> >> >> real memory = 117374976 (111 MB) >> >> avail memory = 100130816 (95 MB) >> >> kbd1 at kbdmux0 >> >> pcib0: <Host to PCI bridge> pcibus 0 on motherboard >> >> pir0: <PCI Interrupt Routing Table: 5 Entries> on motherboard >> >> pci0: <PCI bus> on pcib0 >> >> pci0: <memory, RAM> at device 0.1 (no driver attached) >> >> pci0: <memory, RAM> at device 0.2 (no driver attached) >> >> pci0: <memory, RAM> at device 0.3 (no driver attached) >> >> uhci0: <VIA 83C572 USB controller> port 0xe000-0xe01f irq 15 at >> device >> >> 9.0 >> >> on pci0 >> >> uhci0: [ITHREAD] >> >> uhci0: LegSup = 0x201a >> >> usbus0: <VIA 83C572 USB controller> on uhci0 >> >> uhci1: <VIA 83C572 USB controller> port 0xe100-0xe11f irq 5 at device >> >> 9.1 >> >> on pci0 >> >> uhci1: [ITHREAD] >> >> uhci1: LegSup = 0x2010 >> >> usbus1: <VIA 83C572 USB controller> on uhci1 >> >> ehci0: <VIA VT6202 USB 2.0 controller> mem 0xe8131000-0xe81310ff irq >> 10 >> >> at >> >> device 9.2 on pci0 >> >> ehci0: [ITHREAD] >> >> usbus2: EHCI version 1.0 >> >> usbus2: <VIA VT6202 USB 2.0 controller> on ehci0 >> >> vgapci0: <VGA-compatible display> port 0xe200-0xe2ff mem >> >> 0xe0000000-0xe7ffffff,0xe8120000-0xe812ffff irq 11 at device 13.0 on >> >> pci0 >> >> isab0: <PCI-ISA bridge> at device 17.0 on pci0 >> >> isa0: <ISA bus> on isab0 >> >> atapci0: <VIA 8231 UDMA100 controller> port >> >> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe300-0xe30f at device 17.1 on >> pci0 >> >> ata0: <ATA channel 0> on atapci0 >> >> ata0: [ITHREAD] >> >> ata1: <ATA channel 1> on atapci0 >> >> ata1: [ITHREAD] >> >> pci0: <bridge> at device 17.4 (no driver attached) >> >> vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xe600-0xe6ff mem >> >> 0xe8130000-0xe81300ff irq 15 at device 18.0 on pci0 >> >> vr0: Quirks: 0x0 >> >> vr0: Revision: 0x51 >> >> miibus0: <MII bus> on vr0 >> >> ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0 >> >> ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >> >> vr0: Ethernet address: 00:13:21:ee:26:00 >> >> vr0: [ITHREAD] >> >> cpu0 on motherboard >> >> pmtimer0 on isa0 >> >> atrtc0: <AT realtime clock> at port 0x70-0x71 irq 8 pnpid PNP0b00 on >> >> isa0 >> >> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 irq 1 pnpid >> >> PNP0303 on isa0 >> >> atkbd0: <AT Keyboard> irq 1 on atkbdc0 >> >> kbd0 at atkbd0 >> >> atkbd0: [GIANT-LOCKED] >> >> atkbd0: [ITHREAD] >> >> unknown: <PNP0c01> can't assign resources (memory) >> >> orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xcc000-0xd5fff >> pnpid >> >> ORM0000 on isa0 >> >> sc0: <System console> at flags 0x100 on isa0 >> >> sc0: VGA <16 virtual consoles, flags=0x300> >> >> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on >> >> isa0 >> >> ppc0: parallel port not found. >> >> unknown: <PNP0c01> can't assign resources (memory) >> >> Timecounter "TSC" frequency 798131036 Hz quality 800 >> >> Timecounters tick every 1.000 msec >> >> usbus0: 12Mbps Full Speed USB v1.0 >> >> usbus1: 12Mbps Full Speed USB v1.0 >> >> usbus2: 480Mbps High Speed USB v2.0 >> >> ugen0.1: <VIA> at usbus0 >> >> ushub0: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on >> usbus0 >> >> ugen1.1: <VIA> at usbus1 >> >> ushub1: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on >> usbus1 >> >> ugen2.1: <VIA> at usbus2 >> >> ushub2: <VIA EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on >> usbus2 >> >> ad0: 6149MB <SAMSUNG SV0643D KT100> at ata0-master UDMA33 >> >> GEOM: ad0s1: geometry does not match label (255h,63s != 15h,63s). >> >> ushub0: 2 ports with 2 removable, self powered >> >> ushub1: 2 ports with 2 removable, self powered >> >> Root mount waiting for: usbus2 >> >> Root mount waiting for: usbus2 >> >> ushub2: 4 ports with 4 removable, self powered >> >> Trying to mount root from ufs:/dev/ad0s1a >> >> usb2_alloc_device:1463: set address 2 failed (ignored) >> >> usb2_alloc_device:1499: getting device descriptor at addr 2 failed! >> >> usb2_req_re_enumerate:1414: addr=2, set address failed! (ignored) >> >> usb2_req_re_enumerate:1427: getting device descriptor at addr 2 >> failed! >> >> usb2_req_re_enumerate:1414: addr=2, set address failed! (ignored) >> >> usb2_req_re_enumerate:1427: getting device descriptor at addr 2 >> failed! >> >> ugen0.2: <> at usbus0 (disconnected) >> >> uhub_reattach_port:414: could not allocate new device! >> > >> > Hi, >> > >> > What happens if you put an external USB HUB in between ? >> >> nops, I'll try :) >> >> > There is also a ehci.no_hs sysctl which you can try setting to one. >> >> it passes info to loader, right ? >> >> > Also try enabling uhub debugging during boot. >> > >> > sysctl hw.usb2.uhub.debug=15 >> >> will this take effect even if I can't get to where freebsd kernel takes >> command ? >> > > Yes, you can add it to /boot/loader.conf no hub yet (must get home at night), but ehci line made no effect :( i got to the very same point. thanks, matheus > > --HPS > _______________________________________________ > freebsd-current@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org" > -- We will call you cygnus, The God of balance you shall be
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?044a92c96375670511fc437d6b924923.squirrel>