Date: Thu, 12 Dec 2002 02:46:05 -0500 From: "Craig Reyenga" <creyenga@connectmail.carleton.ca> To: <freebsd-current@freebsd.org> Subject: Isolating the network problem (Was: Any ideas at all about network problem?) Message-ID: <001101c2a1b2$8698b2c0$0200000a@sewer.org>
next in thread | raw e-mail | index | archive | help
I have tried a 3com 905 in place of the Realtek, and I can get speeds of
about 3.5Mb/sec (that's still no 7.9 like I used to get). It does, however,
give a few tx underrun errors at the beginning of large transfers:
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 120 bytes
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 180 bytes
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 240 bytes
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 300 bytes
It should also be noted that at the beginning of this whole ordeal, I was
getting speeds approximately 1/10th of what I used to get with my Realtek
card. A few days ago, I removed the network cables so that I could play
halflife (still havent figured out howto use NAT for this), and when I
reconnected them as per normal, I've been getting 1/100th the speed! (about
80KB/sec). I bought a new cable today thinking that that was the whole
problem, which it is not; the problem still exists.
Anyways, the main point of this message is that I also just discovered that
I can't use my floppy drive for some reason, which I find quite odd. Also,
there are many kernel messages about devices not being configured and such.
Here is the full output:
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-DP2 #0: Fri Nov 29 02:10:15 EST 2002
craig@boss.sewer.org:/usr/src/sys/i386/compile/BOSSKERN
Preloaded elf kernel "/boot/kernel/kernel" at 0xc03d9000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc03d90a8.
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 350797628 Hz
CPU: AMD-K6(tm) 3D processor (350.80-MHz 586-class CPU)
Origin = "AuthenticAMD" Id = 0x58c Stepping = 12
Features=0x8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX>
AMD Features=0xffffffff80000800<SYSCALL,3DNow!>
real memory = 268369920 (255 MB)
avail memory = 256626688 (244 MB)
Initializing GEOMetry subsystem
K6-family MTRR support enabled (2 registers)
netsmb_dev: loaded
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <FIC VA503P > on motherboard
Using $PIR table, 6 entries at 0xc00fdd60
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-safe" frequency 3579545 Hz
can't fetch resources for \\_SB_.PCI0.ISA_.FDC0 - AE_AML_BUFFER_LIMIT
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x6008-0x600b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0x6080-0x60ff,0x6000-0x607f,0xcf8-0xcff
on ac
pi0
---- initial configuration ------------------------
\\_SB_.PCI0.ISA_.LNKA irq 5: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.8.0
\\_SB_.PCI0.ISA_.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.8.1
\\_SB_.PCI0.ISA_.LNKC irq 0: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.8.2
\\_SB_.PCI0.ISA_.LNKD irq 0: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.8.3
\\_SB_.PCI0.ISA_.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.9.0
\\_SB_.PCI0.ISA_.LNKC irq 0: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.9.1
\\_SB_.PCI0.ISA_.LNKD irq 0: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.9.2
\\_SB_.PCI0.ISA_.LNKA irq 5: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.9.3
\\_SB_.PCI0.ISA_.LNKC irq 0: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.10.0
\\_SB_.PCI0.ISA_.LNKD irq 0: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.10.1
\\_SB_.PCI0.ISA_.LNKA irq 5: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.10.2
\\_SB_.PCI0.ISA_.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.10.3
\\_SB_.PCI0.ISA_.LNKA irq 5: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.7.0
\\_SB_.PCI0.ISA_.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.7.1
\\_SB_.PCI0.ISA_.LNKC irq 0: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.7.2
\\_SB_.PCI0.ISA_.LNKD irq 0: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.7.3
\\_SB_.PCI0.ISA_.LNKA irq 5: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.1.0
\\_SB_.PCI0.ISA_.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.1.1
\\_SB_.PCI0.ISA_.LNKC irq 0: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.1.2
\\_SB_.PCI0.ISA_.LNKD irq 0: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.1.3
---- before setting priority for links ------------
\\_SB_.PCI0.ISA_.LNKC:
interrupts: 1 3 4 5 6 7 10 11
12
14 15
penalty: 101100 2100 2100 1600 2100 2100 1600 1100
2100 1
1100 11100
references: 5
priority: 0
\\_SB_.PCI0.ISA_.LNKD:
interrupts: 1 3 4 5 6 7 10 11
12
14 15
penalty: 101100 2100 2100 1600 2100 2100 1600 1100
2100 1
1100 11100
references: 5
priority: 0
---- before fixup boot-disabled links -------------
\\_SB_.PCI0.ISA_.LNKC:
interrupts: 1 3 4 5 6 7 10 11
12
14 15
penalty: 101100 2100 2100 1600 2100 2100 1600 1100
2100 1
1100 11100
references: 5
priority: 62772
\\_SB_.PCI0.ISA_.LNKD:
interrupts: 1 3 4 5 6 7 10 11
12
14 15
penalty: 101100 2100 2100 1600 2100 2100 1600 1100
2100 1
1100 11100
references: 5
priority: 62772
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.PCI0.ISA_.LNKA irq 5: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.8.0
\\_SB_.PCI0.ISA_.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.8.1
\\_SB_.PCI0.ISA_.LNKC irq 11: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.8.2
\\_SB_.PCI0.ISA_.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.8.3
\\_SB_.PCI0.ISA_.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.9.0
\\_SB_.PCI0.ISA_.LNKC irq 11: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.9.1
\\_SB_.PCI0.ISA_.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.9.2
\\_SB_.PCI0.ISA_.LNKA irq 5: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.9.3
\\_SB_.PCI0.ISA_.LNKC irq 11: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.10.0
\\_SB_.PCI0.ISA_.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.10.1
\\_SB_.PCI0.ISA_.LNKA irq 5: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.10.2
\\_SB_.PCI0.ISA_.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.10.3
\\_SB_.PCI0.ISA_.LNKA irq 5: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.7.0
\\_SB_.PCI0.ISA_.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.7.1
\\_SB_.PCI0.ISA_.LNKC irq 11: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.7.2
\\_SB_.PCI0.ISA_.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.7.3
\\_SB_.PCI0.ISA_.LNKA irq 5: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.1.0
\\_SB_.PCI0.ISA_.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.1.1
\\_SB_.PCI0.ISA_.LNKC irq 11: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.1.2
\\_SB_.PCI0.ISA_.LNKD irq 11: [ 1 3 4 5 6 7 10 11 12 14 15]
low,level,sha
rable 0.1.3
pci0: <ACPI PCI bus> on pcib0
agp0: <VIA 82C597 (Apollo VP3) host to PCI bridge> mem 0xe0000000-0xe0ffffff
at
device 0.0 on pci0
pcib1: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C586 ATA33 controller> port 0xe000-0xe00f at device 7.1 on
pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pcib2: <ACPI PCI-PCI bridge> at device 7.3 on pci0
pcib2: could not get PCI interrupt routing table for \\_SB_.PCI0.VTAC -
AE_NOT_F
OUND
pci0: couldn't attach pci bus
device_probe_and_attach: pcib2 attach returned 6
pci0: <network, ethernet> at device 8.0 (no driver attached)
ed0: <NE2000 PCI Ethernet (RealTek 8029)> port 0xec00-0xec1f irq 10 at
device 9.
0 on pci0
ed0: address 00:60:67:3a:b1:70, type NE2000 (16 bit)
pci0: <display, VGA> at device 10.0 (no driver attached)
fdc0: cannot reserve I/O port range (1 ports)
ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A, console
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
fdc0: cannot reserve I/O port range (1 ports)
orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
pmtimer0 on isa0
fdc0: cannot reserve I/O port range (6 ports)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
ipfw2 initialized, divert enabled, rule-based forwarding enabled, default to
acc
ept, logging disabled
ad0: 1668MB <FUJITSU MPA3017ATU> [3390/16/63] at ata0-master UDMA33
ad2: 39083MB <Maxtor 34098H4> [79408/16/63] at ata1-master UDMA33
acd0: CD-RW <RICOH CD-R/RW MP7060A> at ata0-slave PIO3
Mounting root from ufs:/dev/ad0s1a
pcib2: <ACPI PCI-PCI bridge> at device 7.3 on pci0
pcib2: could not get PCI interrupt routing table for \\_SB_.PCI0.VTAC -
AE_NOT_F
OUND
pci0: couldn't attach pci bus
device_probe_and_attach: pcib2 attach returned 6
pcib2: <ACPI PCI-PCI bridge> at device 7.3 on pci0
pcib2: could not get PCI interrupt routing table for \\_SB_.PCI0.VTAC -
AE_NOT_F
OUND
pci0: couldn't attach pci bus
device_probe_and_attach: pcib2 attach returned 6
pcib2: <ACPI PCI-PCI bridge> at device 7.3 on pci0
pcib2: could not get PCI interrupt routing table for \\_SB_.PCI0.VTAC -
AE_NOT_F
OUND
pci0: couldn't attach pci bus
device_probe_and_attach: pcib2 attach returned 6
xl0: <3Com 3c905-TX Fast Etherlink XL> port 0xe800-0xe83f irq 5 at device
8.0 on
pci0
xl0: Ethernet address: 00:60:08:91:4c:fe
miibus0: <MII bus> on xl0
nsphy0: <DP83840 10/100 media interface> on miibus0
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 120 bytes
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 180 bytes
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 240 bytes
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 300 bytes
=============================================
I disabled my USB controller to see if that would help, which it did not.
The USB controller doesn't work in DP2 anyways. _All_ of my hardware did
work just fine, with this same setup, in 4.7-STABLE. Are there any ideas out
there on which driver/otherwise that is at fault?
-Craig
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?001101c2a1b2$8698b2c0$0200000a>