Date: Thu, 08 Dec 2016 21:29:32 +0200 From: "Andriy Voskoboinyk" <s3erios@gmail.com> To: "J.R. Oldroyd" <fbsd@opal.com> Cc: freebsd-wireless@freebsd.org Subject: Re: Boot freeze 11.0p3 during network initialization Message-ID: <op.yr523ie8iew4ia@localhost> In-Reply-To: <20161208095719.30f3c60e@shibato> References: <20161208095719.30f3c60e@shibato>
next in thread | previous in thread | raw e-mail | index | archive | help
Thu, 08 Dec 2016 16:57:19 +0200 було написано J.R. Oldroyd <fbsd@opal.com>: Is there any additional output with wlandebug_wlan0="scan+state+auth+assoc" in /etc/rc.conf ? > I have observed a 11.0p3 freezing during the boot process several times > now. > > It gets as far as running the netif script, displaying the interfaces and > then goes on to devd and dhclient at which point it stops dead. No > keyboard > response. It requires long-press of power to shut it down and restart, > at > which point it typically boots normally: > > wlan0: Ethernet address: 70:1a:04:xx:yy:zz > Created wlan(4) interfaces: wlan0. > Created clone interfaces: lagg0. > re0: link state changed to DOWN > Starting wpa_supplicant. > lagg0: link state changed to DOWN > re0: link state changed to UP > lagg0: link state changed to UP > Starting Network: lo0 re0 wlan0 lagg0. > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 > options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6> > inet6 ::1 prefixlen 128 > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2 > inet 127.0.0.1 netmask 0xff000000 > nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> > groups: lo > re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=82098<VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> > ether 70:1a:04:xx:yy:zz > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > media: Ethernet autoselect (100baseTX <full-duplex>) > status: active > wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu > 1500 > ether 70:1a:04:xx:yy:zz > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) > status: no carrier > ssid "" channel 153 (5765 MHz 11a) > regdomain FCC country US indoor ecm authmode WPA1+WPA2/802.11i > privacy MIXED deftxkey UNDEF txpower 23 bmiss 7 mcastrate 6 > mgmtrate 6 > scanvalid 60 wme burst roaming MANUAL bintval 0 > groups: wlan > lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu > 1500 > ether 70:1a:04:xx:yy:zz > inet6 fe80::721a:4ff:fexx:yyzz%lagg0 prefixlen 64 scopeid 0x4 > nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL> > media: Ethernet autoselect > status: active > groups: lagg > laggproto failover lagghash l2,l3,l4 > laggport: re0 flags=5<MASTER,ACTIVE> > laggport: wlan0 flags=0<> > Starting devd. > Starting dhclient. > ----- freezes dead here > > On a normal boot, the next lines would be: > wlan0: link state changed to UP > Starting pflog. > pflog0: promiscuous mode enabled > > This is a laptop with its re0 and wlan0 interfaces configured together > under lagg using the wlan's MAC as the re's MAC too. > > The relevant config in rc.conf are these: > > ether_wlan0="70:1a:04:xx:yy:zz" > ifconfig_re0="ether $ether_wlan0 -txcsum -rxcsum up" > wlans_ath0=wlan0 > create_args_wlan0="regdomain FCC country US" > ifconfig_wlan0="WPA" > cloned_interfaces="lagg0" > ifconfig_lagg0="laggproto failover laggport re0 laggport wlan0 DHCP" > # WAN_IF > ifconfig_lagg0_ipv6="inet6 accept_rtadv" > > This boot freeze happens probably 5-10% of the time, so problematic > enough. > > This problem was never observed on 10.x or 9.x or even 8.x on the same > laptop. > > What other info can I provide? > > -jr > _______________________________________________ > freebsd-wireless@freebsd.org mailing list > https://lists.freebsd.org/mailman/listinfo/freebsd-wireless > To unsubscribe, send any mail to > "freebsd-wireless-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?op.yr523ie8iew4ia>