Date: Sun, 12 Dec 1999 23:37:10 -0800 (PST) From: obrien@nuxi.cs.ucdavis.edu To: FreeBSD-gnats-submit@freebsd.org Subject: kern/15455: Intel EtherExpress Pro does not properly attach on the Alpha Message-ID: <199912130737.XAA00334@kongur.cs.ucdavis.edu>
index | next in thread | raw e-mail
>Number: 15455
>Category: kern
>Synopsis: Intel EtherExpress Pro does not properly attach on the Alpha
>Confidential: no
>Severity: non-critical
>Priority: medium
>Responsible: freebsd-bugs
>State: open
>Quarter:
>Keywords:
>Date-Required:
>Class: sw-bug
>Submitter-Id: current-users
>Arrival-Date: Sun Dec 12 23:40:02 PST 1999
>Closed-Date:
>Last-Modified:
>Originator: David O'Brien
>Release: FreeBSD 4.0-CURRENT alpha
>Organization:
The FreeBSD Project
>Environment:
AlphaStation 200 4/233
Entering kernel at 0xfffffc00003252a0...
FreeBSD 4.0-CURRENT #9: Sun Dec 12 16:47:24 PST 1999
AlphaStation 200/400 ("Avanti")
AlphaStation 200 4/233, 233MHz
8192 byte page size, 1 processor.
CPU: EV45 (21064A) major=6 minor=2
OSF PAL rev: 0x100000002012e
real memory = 98615296 (96304K bytes)
Physical memory chunk(s):
0x005d0000 - 0x05ffbfff, 94552064 bytes (11542 pages)
avail memory = 91324416 (89184K bytes)
Preloaded elf kernel "kernel" at 0xfffffc00005b4000.
found-> vendor=0x1000, dev=0x0001, revid=0x02
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base 00010000, size 8
map[14]: type 1, range 32, base 82240000, size 8
found-> vendor=0x8086, dev=0x0484, revid=0x43
class=00-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x1011, dev=0x0002, revid=0x24
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base 00010100, size 7
map[14]: type 1, range 32, base 82240100, size 7
found-> vendor=0x8086, dev=0x1229, revid=0x05
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base 90000000, size 12
map[14]: type 1, range 32, base 00010180, size 5
map[18]: type 1, range 32, base 82100000, size 20
found-> vendor=0x1011, dev=0x0004, revid=0x03
class=03-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 88000000, size 27
pci0: <PCI bus> on pcib0
ncr0: <ncr 53c810 fast10 scsi> irq 11 at device 6.0 on pci0
BIOS values: SCNTL3:00 DMODE:00 DCNTL:01
CTEST3:00 CTEST4:00 CTEST5:00
ncr0: minsync=25, maxsync=206, maxoffs=8, 16 dwords burst, normal dma fifo
ncr0: single-ended, open drain IRQ driver
ncr0: interrupting at ISA irq 11
isab0: <Intel 82378IB PCI to ISA bridge> at device 7.0 on pci0
Bus Modes: Bus Park, Resource Lock,
IDE controller: Secondary (170h-177h,376h,377h)
Floppy controller: 370h,371h
Floppy controller: 372h-377h
Keyboard controller: 60h,62h,64h,66h
RTC: 70h-77h
Configuration RAM: 0C00h,0800h-08FFh
Port 92: enabled
isa0: <ISA bus> on isab0
de0: <Digital 21040 Ethernet> irq 5 at device 11.0 on pci0
de0: interrupting at ISA irq 5
de0: DEC 21040 [10Mb/s] pass 2.4
de0: address 00:00:f8:23:5d:51
bpf: de0 attached
fxp0: <Intel EtherExpress Pro 10/100B Ethernet> irq 9 at device 12.0 on pci0
fxp0: interrupting at ISA irq 9
fxp0: Ethernet address ff:ff:ff:ff:ff:ff, 10Mbps
bpf: fxp0 attached
pci0: unknown card (vendor=0x1011, dev=0x0004) at 13.0 irq 10
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0
Calibrating clock(s) ... PCC clock: 233315516 Hz (firmware 233100233 Hz)
sio0: irq maps: 0x21 0x31 0x21 0x21
sio0 at port 0x3f8-0x3ff irq 4 on isa0
sio0: type 16550A, console
sio0: interrupting at ISA irq 4
sio1: reserved for low-level i/o
fdc0: interrupting at ISA irq 6
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbd0: atkbd0, generic (0), config:0x0, flags:0x1f0000, port:0x60-0x6f
atkbd0: interrupting at ISA irq 1
psm0: current command byte:0060
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
sc0: no video adapter is found.
isa_probe_children: probing PnP devices
struct nfssvc_sock bloated (> 256bytes)
Try reducing NFS_UIDHASHSIZ
struct nfsuid bloated (> 128bytes)
Try unionizing the nu_nickname and nu_flag fields
Timecounter "alpha" frequency 233315516 Hz
bpf: sl0 attached
bpf: ppp0 attached
bpf: lo0 attached
>Description:
The Ethernet address on a EtherExpress Pro/100B (i82558-based)
is not properly determined. The machine also looks solid when
the card is ifconfig'ed.
>How-To-Repeat:
# ifconfig -a
de0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 169.237.7.192 netmask 0xffffff00 broadcast 169.237.7.255
ether 00:00:f8:23:5d:51
media: autoselect (10baseT/UTP) status: active
supported media: autoselect 10base5/AUI manual 10baseT/UTP <full-duplex> 10baseT/UTP
fxp0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether ff:ff:ff:ff:ff:ff
media: manual
supported media: manual
sl0: flags=c010<POINTOPOINT,LINK2,MULTICAST> mtu 552
ppp0: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
kongur(r):/home/rootk> ifconfig fxp0 inet 192.168.100.1
[ BOX HANGS SOLID ]
>Fix:
>Release-Note:
>Audit-Trail:
>Unformatted:
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-bugs" in the body of the message
home |
help
Want to link to this message? Use this
URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199912130737.XAA00334>