Date: Thu, 28 Nov 2002 18:17:45 +0100 From: Oliver Enzmann <oliver@cosec.org> To: freebsd-mobile@freebsd.org Subject: USB wierdness on Vaio Message-ID: <3DE64FB9.9030504@cosec.org>
next in thread | raw e-mail | index | archive | help
Hi,
External USB devices on my Sony VAIO R600 laptop disable the USB port
under 5.0-CURRENT (cvsup'ed on the 26th):
Nov 28 17:19:34 vaio kernel: usb_new_device: set address 2 failed
Nov 28 17:19:34 vaio kernel: uhub_explore: usb_new_device failed,
error=SET_ADDR_FAILED
Nov 28 17:19:34 vaio kernel: uhub0: device problem, disabling port 1
However, this laptop also has a built-in (USB) Sony Memorystick reader
that works just fine. Also, the two USB devices I am testing with work
just fine with 5.0-DP2 on an old Dell laptop. The USB devices are:
Iomega USB CDRW9602EXT-B
Y-E DATA USB Floppy Drive
On the Vaio, USB port status changes from - to
1. port 1 powered
2. port 1 addr 0 should never happen!
3. port 1 addr 2: full speed, power 100 mA, unconfigured, product \
0x0055(0x0055), Iomega(0x059b), rev 11.00
4. port 1 enabled
usbdevs -v and Dmesg below.
Your help is greatly appreciated, Oliver
---------------------------------------------------------------
usbdevs -v:
Controller /dev/usb0:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb1:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 addr 2: full speed, self powered, config 1, USB Memory Stick
Slot(0x0056), Sony(0x054c), rev 1.80
port 2 powered
---------------------------------------------------------------
dmesg:
FreeBSD 5.0-CURRENT #1: Thu Nov 28 16:55:29 CET 2002
root@vaio.cosec.org:/usr/src/sys/i386/compile/VAIOMAX
Preloaded elf kernel "/boot/vaiomax/kernel" at 0xc0482000.
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 844610161 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (844.61-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x68a Stepping = 10
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 132644864 (126 MB)
avail memory = 123904000 (118 MB)
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
acpi0: <SONY U1 > on motherboard
Using $PIR table, 9 entries at 0xc00fdf30
Timecounter "ACPI-fast" frequency 3579545 Hz
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 0.1.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 0.1.1
\\_SB_.LNKC irq 0: [ 9] low,level,sharable 0.1.2
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 0.1.3
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 0.2.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 0.31.1
\\_SB_.LNKH irq 9: [ 9] low,level,sharable 0.31.2
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 0.31.3
---- before setting priority for links ------------
\\_SB_.LNKC:
interrupts: 9
penalty: 830
references: 1
priority: 0
\\_SB_.LNKD:
interrupts: 9
penalty: 830
references: 2
priority: 0
---- before fixup boot-disabled links -------------
\\_SB_.LNKD:
interrupts: 9
penalty: 830
references: 2
priority: 1660
\\_SB_.LNKC:
interrupts: 9
penalty: 830
references: 1
priority: 830
---- after fixup boot-disabled links --------------
\\_SB_.LNKD:
interrupts: 9
penalty: 830
references: 2
priority: 1660
\\_SB_.LNKC:
interrupts: 9
penalty: 830
references: 1
priority: 830
---- arbitrated configuration ---------------------
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 0.1.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 0.1.1
\\_SB_.LNKC irq 0: [ 9] low,level,sharable 0.1.2
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 0.1.3
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 0.2.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 0.31.1
\\_SB_.LNKH irq 9: [ 9] low,level,sharable 0.31.2
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 0.31.3
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82815 (i815 GMCH) SVGA controller> mem
0xf4000000-0xf407ffff,0xf8000000-0xfbffffff irq 9 at device 2.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
---- initial configuration ------------------------
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 1.0.0
\\_SB_.LNKC irq 0: [ 9] low,level,sharable 1.2.0
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 1.2.1
\\_SB_.LNKE irq 9: [ 9] low,level,sharable 1.8.0
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 1.12.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 1.12.1
\\_SB_.LNKC irq 0: [ 9] low,level,sharable 1.12.2
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 1.12.3
---- before setting priority for links ------------
\\_SB_.LNKD:
interrupts: 9
penalty: 1670
references: 4
priority: 1660
\\_SB_.LNKC:
interrupts: 9
penalty: 1670
references: 3
priority: 830
---- before fixup boot-disabled links -------------
\\_SB_.LNKD:
interrupts: 9
penalty: 1670
references: 4
priority: 6680
\\_SB_.LNKC:
interrupts: 9
penalty: 1670
references: 3
priority: 5010
---- after fixup boot-disabled links --------------
\\_SB_.LNKD:
interrupts: 9
penalty: 1670
references: 4
priority: 6680
\\_SB_.LNKC:
interrupts: 9
penalty: 1670
references: 3
priority: 5010
---- arbitrated configuration ---------------------
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 1.0.0
\\_SB_.LNKC irq 0: [ 9] low,level,sharable 1.2.0
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 1.2.1
\\_SB_.LNKE irq 9: [ 9] low,level,sharable 1.8.0
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 1.12.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 1.12.1
\\_SB_.LNKC irq 0: [ 9] low,level,sharable 1.12.2
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 1.12.3
pci1: <ACPI PCI bus> on pcib1
fwohci0: <Texas Instruments TSB43AA22> mem
0xf4104000-0xf4107fff,0xf4101000-0xf41017ff irq 9 at device 0.0 on pci1
fwohci0: PCI bus latency was changing to 250.
cache size 8.
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channel is 4.
fwohci0: resetting OHCI...done (0)
fwohci0: BUS_OPT 0xa002 -> 0xf800a002
fwohci0: Link 1394a available S400, 2 ports, maxrec 2048 bytes.
fwohci0: Enable 1394a Enhancements
fwohci0: EUI64 08:00:46:03:00:c3:9a:d3
fwochi_set_intr: 1
firewire0: <IEEE1394(Firewire) bus> on fwohci0
firewire0: firewire bus attach
sbp_identify
sbp_probe
sbp0: <SBP2/SCSI over firewire> on firewire0
sbp_attach
cbb0: <RF5C475 PCI-CardBus Bridge> at device 2.0 on pci1
start (88000000) < sc->membase (f4100000)
end (ffffffff) > sc->memlimit (f41fffff)
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib1: possible interrupts: 9
pcib1: slot 2 INTA routed to irq 9 via \\_SB_.LNKC
fxp0: <Intel Pro/100 Ethernet> port 0x3000-0x303f mem 0xf4100000-0xf4100fff
irq 9 at device 8.0 on pci1
fxp0: Ethernet address 08:00:46:17:51:ab
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH2 ATA100 controller> port 0x1800-0x180f at device 31.1 on
pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port 0x1820-0x183f
irq 9 at device 31.2 on pci0
uhci0: LegSup = 0x00001f20
usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
uhci1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> port 0x2400-0x241f
irq 9 at device 31.4 on pci0
uhci1: LegSup = 0x00002f00
usb1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
umass0: Sony USB Memory Stick Slot, rev 1.10/1.80, addr 2
umass0: 8070i (ATAPI) over CBI with CCI (using CBI); quirks = 0x0000
umass0:1:0:-1: Attached to scbus1 as device 0
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_acad0: <AC adapter> on acpi0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/15 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pmtimer0 on isa0
orm0: <Option ROMs> at iomem 0xdc000-0xdffff,0xd8000-0xdbfff,0xc0000-0xcbfff
on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
spic0: device model type = 2
spic0: <Sony Programmable I/O Controller> at port 0x10a0-0x10a4 on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
firewire0: BUS reset
firewire0: node_id = 0xc000ffc0, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
fw_set_bus_manager: 63->0 (loop=0)
send phy_config root_node=-1 gap_count=1
start AT DMA status=0
acpi_cpu: CPU throttling enabled, 8 steps from 100% to 12.5%
start (88000000) < sc->membase (f4100000)
end (ffffffff) > sc->memlimit (f41fffff)
start (88000000) < sc->membase (f4100000)
end (ffffffff) > sc->memlimit (f41fffff)
wi0: <Instant Wireless Network PC Card> at port 0x100-0x13f irq 9 function 0
config 1 on pccard0
wi0: 802.11 address: xx:yy:xx:yy:xx:yy
wi0: using RF:PRISM2.5 MAC:ISL3873
wi0: Intersil Firmware: Primary 1.00.07, Station 1.03.05
bus_explore done
ad0: 19077MB <HITACHI_DK23BA-20> [38760/16/63] at ata0-master UDMA66
(probe7:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe7:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(probe7:umass-sim0:0:0:0): SCSI Status: Check Condition
(probe7:umass-sim0:0:0:0): UNIT ATTENTION asc:28,0
(probe7:umass-sim0:0:0:0): Not ready to ready change, medium may have changed
(probe7:umass-sim0:0:0:0): Retrying Command (per Sense Data)
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3DE64FB9.9030504>