Date: Mon, 29 Mar 2004 15:51:40 -0800 (PST) From: Julian Elischer <julian@elischer.org> To: freebsd-stable@freebsd.org Subject: Re: USB2 device Message-ID: <Pine.BSF.4.21.0403291550510.29660-100000@InterJet.elischer.org> In-Reply-To: <1080603100.353.3.camel@fast.mmercer.com>
next in thread | previous in thread | raw e-mail | index | archive | help
plug it in and then run usbdevs -v Let's see what it sees. (do you have cam and 'da' and umass all loaded?) On Mon, 29 Mar 2004, Michael E. Mercer wrote: > Julian, > > I built the kernel with ehci, it boots and I see another hub using ehci. > However when I plug in my JumpDrive, it does not get added. > > Michael Mercer > > Copyright (c) 1992-2003 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 4.9-STABLE #0: Mon Mar 29 18:19:39 EST 2004 > mmercer@fast.mmercer.com:/usr/obj/usr/src/sys/g49 > Timecounter "i8254" frequency 1193182 Hz > CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (3006.83-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > Hyperthreading: 2 logical CPUs > real memory = 1072889856 (1047744K bytes) > avail memory = 1039880192 (1015508K bytes) > Programming 24 pins in IOAPIC #0 > IOAPIC #0 intpin 2 -> irq 0 > IOAPIC #0 intpin 17 -> irq 10 > IOAPIC #0 intpin 18 -> irq 5 > IOAPIC #0 intpin 19 -> irq 11 > FreeBSD/SMP: Multiprocessor motherboard: 2 CPUs > cpu0 (BSP): apic id: 0, version: 0x00050014, at 0xfee00000 > cpu1 (AP): apic id: 1, version: 0x00050014, at 0xfee00000 > io0 (APIC): apic id: 2, version: 0x00178020, at 0xfec00000 > Preloaded elf kernel "kernel" at 0xc042b000. > Warning: Pentium 4 CPU: PSE disabled > Pentium Pro MTRR support enabled > md0: Malloc disk > Using $PIR table, 12 entries at 0xc00f50e0 > apm0: <APM BIOS> on motherboard > apm0: found APM BIOS v1.2, connected at v1.2 > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcib0: <Host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > agp0: <Intel 82875P host to AGP bridge> mem 0xd0000000-0xdfffffff at > device 0.0 on pci0 > pcib1: <PCI to PCI bridge (vendor=8086 device=2579)> at device 1.0 on > pci0 > pci1: <PCI bus> on pcib1 > pci1: <NVidia model 0322 graphics accelerator> at 0.0 irq 10 > pcib2: <PCI to PCI bridge (vendor=8086 device=257b)> at device 3.0 on > pci0 > pci2: <PCI bus> on pcib2 > em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.25> port > 0xcf80-0xcf9f mem 0xfe9e0000-0xfe9fffff irq 5 at device 1.0 on pci2 > em0: Speed:N/A Duplex:N/A > uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xef00-0xef1f > irq 10 at device 29.0 on pci0 > usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0 > usb0: USB revision 1.0 > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xef20-0xef3f > irq 11 at device 29.1 on pci0 > usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1 > usb1: USB revision 1.0 > uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 2 ports with 2 removable, self powered > uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xef40-0xef5f > irq 5 at device 29.2 on pci0 > usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2 > usb2: USB revision 1.0 > uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub2: 2 ports with 2 removable, self powered > uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xef80-0xef9f > irq 10 at device 29.3 on pci0 > usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3 > usb3: USB revision 1.0 > uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub3: 2 ports with 2 removable, self powered > ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfebffc00-0xfebfffff irq > 11 at device 29.7 on pci0 > ehci_pci_attach: companion usb0 > ehci_pci_attach: companion usb1 > ehci_pci_attach: companion usb2 > ehci_pci_attach: companion usb3 > usb4: EHCI version 1.0 > usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 > usb4: <EHCI (generic) USB 2.0 controller> on ehci0 > usb4: USB revision 2.0 > uhub4: (0x8086) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 > uhub4: 8 ports with 8 removable, self powered > uhub5: NEC Corporation USB2.0 Hub Controller, class 9/0, rev 2.00/1.00, > addr 2 > uhub5: 4 ports with 4 removable, self powered > uhub5: cannot open interrupt pipe > device_probe_and_attach: uhub5 attach returned 6 > uhub5: NEC Corporation USB2.0 Hub Controller, class 9/0, rev 2.00/1.00, > addr 2 > uhub5: 4 ports with 4 removable, self powered > uhub5: cannot open interrupt pipe > device_probe_and_attach: uhub5 attach returned 6 > pcib3: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on > pci0 > pci3: <PCI bus> on pcib3 > fwohci0: <VIA VT6306> port 0xdc00-0xdc7f mem 0xfeaff800-0xfeafffff irq 5 > at device 3.0 on pci3 > fwohci0: OHCI version 1.0 (ROM=1) > fwohci0: No. of Isochronous channel is 8. > fwohci0: EUI64 00:e0:18:00:00:58:2a:e6 > fwohci0: Phy 1394a available S400, 3 ports. > fwohci0: Link S400, max_rec 2048 bytes. > firewire0: <IEEE1394(FireWire) bus> on fwohci0 > fwe0: <Ethernet over FireWire> on firewire0 > if_fwe0: Fake Ethernet address: 02:e0:18:58:2a:e6 > fwohci0: Initiate bus reset > fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode > firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) > firewire0: bus manager 0 (me) > isab0: <PCI to ISA bridge (vendor=8086 device=24d0)> at device 31.0 on > pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel ICH5 ATA100 controller> port > 0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 irq 0 at device 31.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > pci0: <unknown card> (vendor=0x8086, dev=0x24d3) at 31.3 irq 10 > pcm0: <Intel ICH5 (82801EB)> port 0xee80-0xeebf,0xe800-0xe8ff mem > 0xfebff400-0xfebff4ff,0xfebff800-0xfebff9ff irq 10 at device 31.5 on > pci0 > pcm0: <Analog Devices AD1985 AC97 Codec> > orm0: <Option ROM> at iomem 0xc0000-0xcefff on isa0 > pmtimer0 on isa0 > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on > isa0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model IntelliMouse Explorer, device ID 4 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on > isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1 at port 0x2f8-0x2ff irq 3 on isa0 > sio1: type 16550A > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > ppc0: FIFO with 16/16/9 bytes threshold > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > APIC_IO: Testing 8254 interrupt delivery > APIC_IO: routing 8254 via IOAPIC #0 intpin 2 > SMP: AP CPU #1 Launched! > ad0: 39205MB <Maxtor 6E040L0> [79656/16/63] at ata0-master UDMA100 > ad3: 194481MB <Maxtor 6Y200P0> [395136/16/63] at ata1-slave UDMA100 > acd0: DVD-R <OPTORITEDVD RW DD0203> at ata1-master PIO4 > Mounting root from ufs:/dev/ad3s1a > em0: Link is up 100 Mbps Full Duplex > em0: Link is up 100 Mbps Full Duplex > > >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.21.0403291550510.29660-100000>