Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 29 Dec 2006 00:12:26 +0800
From:      "Janvier Pang" <janvier.roc@gmail.com>
To:        "Abdullah Al-Marrie" <almarrie@gmail.com>,  "Janvier Pang" <janvier.roc@gmail.com>, freebsd-x11@freebsd.org
Subject:   Re: Can anybody change the resolution to 1280x800?
Message-ID:  <7deba7c00612280812s51089c57ie57c11e32d21c0bb@mail.gmail.com>
In-Reply-To: <20061228145033.GA35875@owl.midgard.homeip.net>
References:  <7deba7c00612260923ja2c6eccs52e7004d7fdec33@mail.gmail.com> <499c70c0612261017yf098367u598d4ac8d191f1b1@mail.gmail.com> <20061228145033.GA35875@owl.midgard.homeip.net>

next in thread | previous in thread | raw e-mail | index | archive | help
Hi,

But I'm truely believe that the vesa can use the resolution.

That's because I can found such information in my log file if I use the vesa
driver:

...
(II) VESA(0): Gamma: 2.20
(II) VESA(0): No DPMS capabilities specified; RGB/Color Display
(II) VESA(0): First detailed timing is preferred mode
(II) VESA(0): redX: 0.575 redY: 0.359   greenX: 0.319 greenY: 0.532
(II) VESA(0): blueX: 0.155 blueY: 0.129   whiteX: 0.312 whiteY: 0.328
(II) VESA(0): Manufacturer's mask: 0
(II) VESA(0): Supported additional Video Mode:
(II) VESA(0): clock: 68.9 MHz   Image Size:  331 x 207 mm
(II) VESA(0): h_active: 1280  h_sync: 1301  h_sync_end 1333 h_blank_end 1408
h_border: 0
(II) VESA(0): v_active: 800  v_sync: 804  v_sync_end 808 v_blanking: 816
v_border: 0
(II) VESA(0):  QUANTADISPLAY
(II) VESA(0):  QD15TL072
(II) VESA(0): Searching for matching VESA mode(s):
(==) VESA(0): Write-combining range (0x0,0x1000) was already clear
...

It said that the vesa found the correct additional video mode with 1280x800
resolution on my card. The problem is: how can I apply this mode?

Thanks for your kindly reply.

B.Rgds.

Janvier Pag

On 12/28/06, Erik Trulsson <ertr1013@student.uu.se> wrote:
>
> On Tue, Dec 26, 2006 at 09:17:59PM +0300, Abdullah Al-Marrie wrote:
> > On 12/26/06, Janvier Pang <janvier.roc@gmail.com> wrote:
> > >Dear All,
> > >
> > >I have a laptop, there're ATI Mobility Radeon X1300 display card and
> wide
> > >screen with 1280x800 resolutions on it.
> > >
> > >I'd like to use the native ati driver, Unfortunately I can't find any
> > >available driver about this card on the internet. So that I  must
> choose
> > >another way to use this card.
> > >
> > >I configured the vesa driver in /etc/X11/xorg.conf, and then start the
> X. I
> > >got the following message in /var/log/Xorg.0.log:
> > >
>
> > >
> > >...
> > >(II) VESA(0): Total Memory: 256 64KB banks (16384kB)
> > >(WW) VESA(0): config file hsync range 31.5-64.3kHz not within DDC hsync
> > >ranges.
> > >(WW) VESA(0): config file vrefresh range 50-70Hz not within DDC
> vrefresh
> > >ranges.
> > >(II) VESA(0): My Monitor: Using hsync range of 31.50-64.30 kHz
> > >(II) VESA(0): My Monitor: Using vrefresh range of 50.00-70.00 Hz
> > >(II) VESA(0): Not using mode "1280x800" (no mode of this name)
> > >(--) VESA(0): Virtual size is 1024x768 (pitch 1024)
> > >(**) VESA(0):  Built-in mode "1024x768"
> > >(**) VESA(0):  Built-in mode "1024x768"
> > >(**) VESA(0):  Built-in mode "800x600"
> > >...
> > >
> > >It said "1280x800" mode cound not to be found, but I have added this
> mode
> > >into /etc/X11/xorg.conf. Why it can not to be detected?
> > >
> > >If I can use the additional video mode, I can use my wide screen under
> > >1280x800 resolution I think. Could anybody give me some hints about how
> to
> > >apply the additional video mode?
> > >
> > >Thanks.
> > >
> > >Janvier Pang.
> >
> > Here is my xorg.conf file and I use ATI Radeon 1100
> >
> > I'm loading the dri module which is Xorg module to support radeon
>
> No, it is not.  dri/drm are for using accelerated 3D (on those cards where
> this is supported) and has nothing to do with which resolutions you can
> use.
>
>
> X.org 6.9 does not have any support for the X1300.  There might be some
> support
> for it in the upcoming X.org 7.x (for x > 0), but I am not sure about
> that.
>
>
> If you are using the 'vesa' driver I believe that you can only use those
> modes that have been pre-programmed in the card's BIOS.  1280x800 (or
> other
> wide-screen resolutions) is usually not one of those.
>
>
>
> --
> <Insert your favourite quote here.>
> Erik Trulsson
> ertr1013@student.uu.se
>



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?7deba7c00612280812s51089c57ie57c11e32d21c0bb>