Date: Sat, 12 May 2001 20:09:44 +0200 (CEST) From: "Hartmann, O." <ohartman@klima.physik.uni-mainz.de> To: <freebsd-stable@freebsd.org> Cc: <freebsd-questions@freebsd.org> Subject: FreeBSD 4.3-STABLE Install problems, BOOT FAILURE after fresh installation Message-ID: <Pine.BSF.4.33.0105121957001.90903-100000@klima.physik.uni-mainz.de>
next in thread | raw e-mail | index | archive | help
Hello.
I have the follwoing problem:
Server box with hardware as decribed below:
ASUS A7V, AMD TBird 850 MHz, 512 MB RAM (2x 256 MB PC133 ECC),
Intel EtherExpress NIC, LSI Logic 21040-33 Ultra 160 SCSI adapter
and three IBM drives, as shown in the dmesg-output below. This
configuration works very well and stable.
Now we would like to change the harddrives and I got two IBM DDYS 18GB drives,
new, fresh low level formatted.
After booting from the last FreeBSD 4.3-STABLE ISO image CD I installed
on the first hard drive two slices and set the first one bootable (Option A).
All the others were installed the usual way and when sysinstall asks for
how to leave the bootblock I tell it to install a "normal bootblock". So far.
I can see how fast the installation proceeds and after rebooting I run into
the problem that there is no bootblock.
For the first time I tried to reduce the clock of the Ultra160 SCSI controller
so it should work with 80,40 or 20 MB/s, but that did not work either. As you can
see, the working configuration operates at 40 MB/s maximum, SE, not LVD.
Has anyone any idea what's going wrong? If it should be asured that the hardware
is faulty (as it seems the first view to me) I should check more sophisticated
next time, but if there is a known problem in FreeBSD 4.3-STABLE in installing boot=
blocks you should inform me.
Thanks a lot for your help in advance.
O. Hartmann
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.3-STABLE #63: Wed May 2 16:13:51 CEST 2001
root@mail.physik.uni-mainz.de:/usr/system/obj/usr/vol1/src/sys/MAIL
Timecounter "i8254" frequency 1193153 Hz
Timecounter "TSC" frequency 857615836 Hz
CPU: AMD Athlon(tm) Processor (857.62-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x642 Stepping = 2
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
AMD Features=0xc0440000<<b18>,AMIE,DSP,3DNow!>
real memory = 536788992 (524208K bytes)
avail memory = 518852608 (506692K bytes)
Preloaded elf kernel "kernel" at 0xc0390000.
ccd0-3: Concatenated disk drivers
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib2: <PCI to PCI bridge (vendor=1106 device=8305)> at device 1.0 on pci0
pci1: <PCI bus> on pcib2
pci1: <Matrox MGA G200 AGP graphics accelerator> at 0.0 irq 11
isab0: <VIA 82C686 PCI-ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
pci0: <VIA Apollo ATA controller> at 4.1
pci0: <VIA 83C572 USB controller> at 4.2 irq 15
pci0: <VIA 83C572 USB controller> at 4.3 irq 15
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xa400-0xa43f mem 0xe0800000-0xe08fffff,0xe1000000-0xe1000fff irq 10 at device 11.0 on pci0
fxp0: Ethernet address 00:d0:b7:4c:2e:9c
sym0: <1010-33> port 0xa000-0xa0ff mem 0xdf800000-0xdf801fff,0xe0000000-0xe00003ff irq 11 at device 12.0 on pci0
sym0: Symbios NVRAM, ID 7, Fast-80, SE, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: handling phase mismatch from SCRIPTS.
sym1: <1010-33> port 0x9800-0x98ff mem 0xde800000-0xde801fff,0xdf000000-0xdf0003ff irq 10 at device 12.1 on pci0
sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: using LOAD/STORE-based firmware.
sym1: handling phase mismatch from SCRIPTS.
sym1: SCAN AT BOOT disabled for targets 0 1 2 3 8 9 10 11 12 13 14 15.
pci0: <unknown card> (vendor=0x105a, dev=0x0d30) at 17.0 irq 10
pcib1: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib1
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <8 virtual consoles, flags=0x200>
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 flags 0x10 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 flags 0x8 on isa0
ppc0: SMC-like chipset (ECP-only) in ECP mode
ppc0: FIFO with 16/16/8 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ppc1: <Parallel port> at port 0x278-0x27f irq 5 flags 0x8 on isa0
ppc1: Generic chipset (ECP-only) in ECP mode
ppi1: <Parallel I/O> on ppbus1
DUMMYNET initialized (010124)
IP packet filtering initialized, divert enabled, rule-based forwarding enabled, default to deny, unlimited logging
IPsec: Initialized Security Association Processing.
Waiting 3 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
(noperiph:sym1:0:-1:-1): SCSI BUS reset delivered.
Mounting root from ufs:/dev/da0s1a
cd0 at sym1 bus 0 target 4 lun 0
cd0: <TEAC CD-ROM CD-532S 1.0A> Removable CD-ROM SCSI-2 device
cd0: 20.000MB/s transfers (20.000MHz, offset 16)
cd0: Attempt to query device size failed: NOT READY, Medium not present
cd1 at sym1 bus 0 target 6 lun 0
cd1: <PLEXTOR CD-R PX-R412C 1.07> Removable CD-ROM SCSI-2 device
cd1: 10.000MB/s transfers (10.000MHz, offset 8)
cd1: Attempt to query device size failed: NOT READY, Medium not present
da1 at sym0 bus 0 target 1 lun 0
da1: <IBM DCAS-34330W S65A> Fixed Direct Access SCSI-2 device
da1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
da1: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C)
da0 at sym0 bus 0 target 0 lun 0
da0: <IBM DCAS-32160W S65A> Fixed Direct Access SCSI-2 device
da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
da0: 2063MB (4226725 512 byte sectors: 255H 63S/T 263C)
da2 at sym0 bus 0 target 2 lun 0
da2: <IBM DDRS-39130W S97B> Fixed Direct Access SCSI-2 device
da2: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da2: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
link_elf: symbol splash_register undefined
fxp0: promiscuous mode enabled
---------------------------
--
MfG
O. Hartmann
ohartman@klima.physik.uni-mainz.de
----------------------------------------------------------------
IT-Administration des Institut fuer Physik der Atmosphaere (IPA)
----------------------------------------------------------------
Johannes Gutenberg Universitaet Mainz
Becherweg 21
55099 Mainz
Tel: +496131/3924662 (Maschinensaal)
Tel: +496131/3924144
FAX: +496131/3923532
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.33.0105121957001.90903-100000>