Date: Tue, 17 Jul 2007 21:27:40 -0700 From: "Kip Macy" <kip.macy@gmail.com> To: "Mike Tancsa" <mike@sentex.net>, freebsd-current@freebsd.org Subject: Re: chelsio driver and Myricom driver Message-ID: <b1fa29170707172127y2b6a13f8lb678c026dad732c3@mail.gmail.com> In-Reply-To: <200707180239.l6I2dgD1010356@lava.sentex.ca> References: <200707180239.l6I2dgD1010356@lava.sentex.ca>
next in thread | previous in thread | raw e-mail | index | archive | help
You need to use the module in order to update the firmware. The
firmware will be automatically be updated when you up an interface on
the card.
-Kip
On 7/17/07, Mike Tancsa <mike@sentex.net> wrote:
> Hi,
>
> I am trying to run a recent current with the Chelsio 10GigE card
> below and it tries to load but has the following complaint.
>
> cxgbc0: <Chelsio T310 RNIC, 1 port> mem
> 0xe0201000-0xe0201fff,0xe0800000-0xe0ffffff,0xe0200000-0xe0200fff irq
> 16 at device 0.0 on pci10
> cxgbc0: found wrong FW version (4.0), driver needs version 4.5
> cxgbc0: firmware needs to be updated to version 4.5.0
> cxgbc0: found wrong TP version (0.0), driver needs version 1.1
> cxgbc0: SRAM needs to be updated to version b-1.1.0
> cxgb0: <Port 0 10GBASE-CX4> on cxgbc0
> cxgb0: Ethernet address: 00:07:43:04:01:2c
>
> Where do I get the firmware from ? The website only has 4.3 ? Also,
> how do I update the SRAM. Sorry if these are obvious questions, but
> I am new to CURRENT with such drivers. I have the driver compiled
> into the kernel
>
>
> With the Myricom, it seems to work, but it doesnt detect the cx4
> media type for some reason.
>
> # ifconfig mxge0
> mxge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 9000
>
> options=1bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4>
> ether 00:60:dd:47:c6:c4
> inet 192.168.10.3 netmask 0xffffff00 broadcast 192.168.10.255
> media: <unknown type> (autoselect <full-duplex>)
> status: active
>
> The port is up and I can ping across it so it is working.
>
> TenGigabitEthernet2/3 is up, line protocol is up (connected)
> Hardware is C6k 10000Mb 802.3, address is 0018.bab0.2036 (bia
> 0018.bab0.2036)
> Description: leopard3 mxge0
> MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation ARPA, loopback not set
> Full-duplex, 10Gb/s
> input flow-control is off, output flow-control is on
> ARP type: ARPA, ARP Timeout 04:00:00
> Last input never, output 00:00:55, output hang never
> Last clearing of "show interface" counters never
> Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
> Queueing strategy: fifo
> Output queue: 0/40 (size/max)
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 8 packets input, 588 bytes, 0 no buffer
> Received 5 broadcasts, 0 runts, 0 giants, 0 throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
> 0 input packets with dribble condition detected
> 403 packets output, 30468 bytes, 0 underruns
> 0 output errors, 0 collisions, 1 interface resets
> 0 babbles, 0 late collision, 0 deferred
> 0 lost carrier, 0 no carrier
> 0 output buffer failures, 0 output buffers swapped out
>
>
> ---Mike
>
>
> --------------------------------------------------------------------
> Mike Tancsa, tel +1 519 651 3400
> Sentex Communications, mike@sentex.net
> Providing Internet since 1994 www.sentex.net
> Cambridge, Ontario Canada www.sentex.net/mike
>
> _______________________________________________
> freebsd-current@freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-current
> To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"
>
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?b1fa29170707172127y2b6a13f8lb678c026dad732c3>