Date: Tue, 6 Mar 2001 09:50:54 +0100 (CET) From: Patrik Astrom <patrik@astrom.net> To: <freebsd-questions@freebsd.org> Subject: Problems with Compaq SmartArray 3200 on a DL380. Message-ID: <Pine.BSF.4.32.0103060950130.36344-200000@styx.astrom.net>
next in thread | raw e-mail | index | archive | help
[-- Attachment #1 --]
Hi everyone !,
I have a problem with a Compaq DL380 with two array controllers.
I will try to describe my problem.
I have two mirrored 9,1 Gb disks on my Intergrated SmartArray Controller
which I boot from, I have 14 18,2 Gb disks in a Raid5 configuration with
one hotspare.
When I boot up the box I get the following lines..
ida1: <Compaq Smart Array 3200 controller> port 0x4000-0x40ff mem
0xc6ffff00-0xc6ffffff irq 15 at device 0.0 on pci4
device_probe_and_attach: ida1 attach returned 12
And I have tried to search for info about the above but without luck, so
I'm hoping that someone know what the problem might be !. I have another
DL380 with almost the same configuration, the configuration differs on the
subject of booting, I boot that box from the external array via the 3200
Controller and don't use the Internal SmartArray.
Also during Array Init I get the the following message on sceen before the
3200 array is done init'ing.
Host system does not support PCI data bus parity checking.
Don't got a clue what that's all about !?
I'm including my "dmesg" as a attachment.
Most gratefull for any hints or suggestions.
Regards
Patrik Astrom
[-- Attachment #2 --]
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.2-RELEASE #0: Mon Mar 5 16:46:20 CET 2001
root@xxxxxxx.xxxxx.net:/usr/src/sys/compile/ITNETAPP01
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (797.48-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 1207943168 (1179632K bytes)
avail memory = 1171308544 (1143856K bytes)
Changing APIC ID for IO APIC #0 from 0 to 8 on chip
Programming 35 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 8, version: 0x00220011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc030c000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc030c09c.
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
ida0: <Compaq Integrated Array controller> port 0x2000-0x20ff mem 0xc4000000-0xc4ffffff,0xc5000000-0xc5ffffff irq 10 at device 1.0 on pci0
ida0: drives=1 firm_rev=1.42
idad0: <Compaq Logical Drive> on ida0
idad0: 8670MB (17756160 sectors), blocksize=512
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x2400-0x243f mem 0xc3e00000-0xc3efffff,0xc3fff000-0xc3ffffff irq 11 at device 2.0 on pci0
fxp0: Ethernet address 00:02:a5:09:38:25
pci0: <ATI Mach64-GV graphics accelerator> at 3.0
pci0: <unknown card> (vendor=0x0e11, dev=0xa0f0) at 4.0
isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks ROSB4 ATA33 controller> port 0x2c00-0x2c0f at device 15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pcib3: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
pci3: <PCI bus> on pcib3
xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0x3000-0x307f mem 0xc6efff80-0xc6efffff irq 5 at device 4.0 on pci3
xl0: Ethernet address: 00:50:da:51:21:f2
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib1: <IBM 82351 PCI-PCI bridge> at device 6.0 on pci3
pci4: <PCI bus> on pcib1
ida1: <Compaq Smart Array 3200 controller> port 0x4000-0x40ff mem 0xc6ffff00-0xc6ffffff irq 15 at device 0.0 on pci4
device_probe_and_attach: ida1 attach returned 12
eisa0: <EISA bus> on motherboard
mainboard0: <CPQ0692 (System Board)> on eisa0 slot 0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: Broken MP table detected: 8254 is not connected to IOAPIC #0 intpin 2
APIC_IO: routing 8254 via 8259 and IOAPIC #0 intpin 0
SMP: AP CPU #1 Launched!
acd0: CDROM <Compaq CRN-8241B> at ata0-master using PIO4
no devsw (majdev=0 bootdev=0xa0200000)
Mounting root from ufs:/dev/idad0s1a
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.32.0103060950130.36344-200000>