Date: Sun, 6 Jun 2004 12:12:15 -0700 (PDT) From: Luke <luked@pobox.com> To: freebsd-questions@freebsd.org Subject: Please help me understand pciutils output Message-ID: <Pine.NEB.4.60.0406061152350.14275@otaku.freeshell.org>
next in thread | raw e-mail | index | archive | help
I suspect that my PCI bus is incompatible with some of the PCI cards I'm
trying to use with it. The motherboard was made in 1996 and these cards
are all much newer. One of the cards gives USB 2.0 support, but I'm not
getting anywhere near USB 2.0 speed out of the USB 2.0 devices I plug into
it. I wonder if the problem is the speed of the PCI bus that the USB
controller is plugged into.
I installed pciutils-2.1.11_1 and ran "lspci -vv" to get the following log.
Should I be disturbed by the "66Mhz-" status on everything except the RAID
card, which is "66MHz+"?
Should I adjust the latency on anything?
Should I stop plugging new cards into old boards?
00:00.0 Host bridge: Intel Corp. 430HX - 82439HX TXC [Triton II] (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
00:07.0 Non-VGA unclassified device: Intel Corp. 82375EB (rev 05)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 248
00:08.0 IDE interface: CMD Technology Inc PCI0646 (rev 01) (prog-if 8a
[Master SecP PriP])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 14
Region 0: I/O ports at 01f0
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170
Region 3: I/O ports at 0374
Region 4: I/O ports at ffa0
00:0c.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: Belkin Root Hub
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (250ns min, 10500ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ffafc000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: Belkin Root Hub
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 10500ns max), cache line size 08
Interrupt: pin B routed to IRQ 11
Region 0: Memory at ffafd000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20
[EHCI])
Subsystem: Belkin Root Hub
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4000ns min, 8500ns max), cache line size 08
Interrupt: pin C routed to IRQ 9
Region 0: Memory at ffafef00 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 RAID bus controller: Promise Technology, Inc.: Unknown device 3371
(rev 02)
Subsystem: Promise Technology, Inc.: Unknown device 3371
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 96 (1000ns min, 4500ns max), cache line size 90
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ee80
Region 1: I/O ports at efa0
Region 2: I/O ports at ea80
Region 3: Memory at ffaff000 (32-bit, non-prefetchable)
Region 4: Memory at ffac0000 (32-bit, non-prefetchable)
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.NEB.4.60.0406061152350.14275>