Date: Fri, 28 Mar 2025 12:54:32 +0000 (UTC) From: "Bjoern A. Zeeb" <bz@freebsd.org> To: Baptiste Daroussin <bapt@freebsd.org> Cc: FreeBSD wireless mailing list <wireless@freebsd.org> Subject: Re: iwlwifi unable to create wlan0 Message-ID: <8421106s-4820-2r9q-o48p-441o243p79qp@serrofq.bet> In-Reply-To: <t4i3vtvxey7uxuuxk4lfchuoixpveiifcwpl76xgmuejghvrrf@umg6mv45gfhd> References: <2cpg7jp6r37xlkodljpb3h6drozcrhzxsjaeuj3zg4kn5wt3pq@oacdr4db3l3v> <p2q4p0p5-8126-5078-qp19-31n4opnp9nr0@SerrOFQ.bet> <z2cg65iiejk4bvnldv6w4zlgmk52vq2erwmhpfv5mnzrrvpauz@vb5soatwbcar> <r51602p6-0oqo-34rs-8583-1so394ps7637@serrofq.bet> <wmrsuyqvl55dpxaxpslvds2sioyb7i7a3jj7nrsezelpyfm4jz@bi7ahoumclsu> <415622r8-s100-9r3q-o033-48p190prqpq5@serrofq.bet> <t4i3vtvxey7uxuuxk4lfchuoixpveiifcwpl76xgmuejghvrrf@umg6mv45gfhd>
index | next in thread | previous in thread | raw e-mail
On Fri, 28 Mar 2025, Baptiste Daroussin wrote: > Full version: Thanks again! I looked up the AX101 and it seems until last year even people on Linux complained that it worked on Windows but not really on Linux. I found one (seem these cheap thingys are rare) and it should be coming next week-ish (from Italy) so I ccan go and see without having to do so much remote debugging but also to be able to keep testing changes on it. > Intel(R) Wireless WiFi based driver for FreeBSD > iwlwifi0: <iwlwifi> mem 0x6001114000-0x6001117fff at device 20.3 on pci0 > iwlwifi0: Detected crf-id 0x501, cnv-id 0x80400 wfpm id 0x80000030 > iwlwifi0: PCI dev 54f0/0244, rev=0x370, rfid=0x10c000 > iwlwifi0: Detected Intel(R) Wi-Fi 6 AX101 > iwlwifi0: successfully loaded firmware image 'iwlwifi-so-a0-hr-b0-89.ucode' > iwlwifi0: TLV_FW_FSEQ_VERSION: FSEQ Version: 0.0.2.42 > iwl-debug-yoyo.bin: could not load binary firmware /boot/firmware/iwl-debug-yoyo.bin either > iwl-debug-yoyo.bin: could not load binary firmware /boot/firmware/iwl-debug-yoyo.bin either > iwl-debug-yoyo_bin: could not load binary firmware /boot/firmware/iwl-debug-yoyo_bin either > iwl_debug_yoyo_bin: could not load binary firmware /boot/firmware/iwl_debug_yoyo_bin either > iwlwifi0: loaded firmware version 89.6b44fa0b.0 so-a0-hr-b0-89.ucode op_mode iwlmvm > iwlwifi0: WFPM_UMAC_PD_NOTIFICATION: 0x20 > iwlwifi0: WFPM_LMAC2_PD_NOTIFICATION: 0x1f > iwlwifi0: WFPM_AUTH_KEY_0: 0x90 > iwlwifi0: CNVI_SCU_SEQ_DATA_DW9: 0x10 > iwlwifi0: Detected RF HR1 B3, rfid=0x10c000 > iwlwifi0: RFIm is deactivated, reason = 4 > iwlwifi0: base HW address: b0:dc:ef:18:9c:32 > lkpi_l80211_to_net80211_cyphers: unsupported WLAN Cipher Suite 0x000fac | 8 (GCMP) > lkpi_l80211_to_net80211_cyphers: unsupported WLAN Cipher Suite 0x000fac | 9 (GCMP_256) > lkpi_l80211_to_net80211_cyphers: unsupported WLAN Cipher Suite 0x000fac | 6 (AES_CMAC) > lkpi_l80211_to_net80211_cyphers: unsupported WLAN Cipher Suite 0x000fac | 11 (BIP_GMAC_128) > lkpi_l80211_to_net80211_cyphers: unsupported WLAN Cipher Suite 0x000fac | 12 (BIP_GMAC_256) > iwlwifi0: WFPM_UMAC_PD_NOTIFICATION: 0x20 > iwlwifi0: WFPM_LMAC2_PD_NOTIFICATION: 0x1f > iwlwifi0: WFPM_AUTH_KEY_0: 0x90 > iwlwifi0: CNVI_SCU_SEQ_DATA_DW9: 0x10 > iwlwifi0: RFIm is deactivated, reason = 4 > wlan0: Ethernet address: b0:dc:ef:18:9c:32 > iwlwifi0: WFPM_UMAC_PD_NOTIFICATION: 0x20 > iwlwifi0: WFPM_LMAC2_PD_NOTIFICATION: 0x1f > iwlwifi0: WFPM_AUTH_KEY_0: 0x90 > iwlwifi0: CNVI_SCU_SEQ_DATA_DW9: 0x10 > iwlwifi0: RFIm is deactivated, reason = 4 > wlan0: Ethernet address: b0:dc:ef:18:9c:32 > iwlwifi0: Microcode SW error detected. Restarting 0x0. > iwlwifi0: Start IWL Error Log Dump: > iwlwifi0: Transport status: 0x0000004B, valid: 6 > iwlwifi0: Loaded firmware version: 89.6b44fa0b.0 so-a0-hr-b0-89.ucode > iwlwifi0: 0x00000071 | NMI_INTERRUPT_UMAC_FATAL > iwlwifi0: 0x000002F1 | trm_hw_status0 > iwlwifi0: 0x00000000 | trm_hw_status1 > iwlwifi0: 0x004D7360 | branchlink2 > iwlwifi0: 0x004CD3A2 | interruptlink1 > iwlwifi0: 0x004CD3A2 | interruptlink2 > iwlwifi0: 0x00006044 | data1 > iwlwifi0: 0x00000010 | data2 > iwlwifi0: 0x00000000 | data3 > iwlwifi0: 0x000181F5 | beacon time > iwlwifi0: 0xC1BDCE12 | tsf low > iwlwifi0: 0x00000231 | tsf hi > iwlwifi0: 0x00000000 | time gp1 > iwlwifi0: 0x0046E3C3 | time gp2 > iwlwifi0: 0x00000001 | uCode revision type > iwlwifi0: 0x00000059 | uCode version major > iwlwifi0: 0x6B44FA0B | uCode version minor > iwlwifi0: 0x00000370 | hw version > iwlwifi0: 0x18C80002 | board version > iwlwifi0: 0x80F5FF00 | hcmd > iwlwifi0: 0x00120000 | isr0 > iwlwifi0: 0x60000000 | isr1 iwlwifi0: 0x48F00002 | isr2 > iwlwifi0: 0x00C3000D | isr3 > iwlwifi0: 0x00000000 | isr4 > iwlwifi0: 0x00320103 | last cmd Id > iwlwifi0: 0x00006044 | wait_event > iwlwifi0: 0x00000080 | l2p_control > iwlwifi0: 0x00000820 | l2p_duration > iwlwifi0: 0x0000003F | l2p_mhvalid > iwlwifi0: 0x00CE18B8 | l2p_addr_match > iwlwifi0: 0x00000009 | lmpm_pmg_sel > iwlwifi0: 0x00000000 | timestamp > iwlwifi0: 0x00004870 | flow_handler > iwlwifi0: Start IWL Error Log Dump: > iwlwifi0: Transport status: 0x0000004B, valid: 7 > iwlwifi0: 0x20101A27 | ADVANCED_SYSASSERT > iwlwifi0: 0x00000000 | umac branchlink1 > iwlwifi0: 0x804824F0 | umac branchlink2 > iwlwifi0: 0x010581B4 | umac interruptlink1 > iwlwifi0: 0x00000000 | umac interruptlink2 > iwlwifi0: 0x00010000 | umac data1 > iwlwifi0: 0x00000000 | umac data2 > iwlwifi0: 0xDEADBEEF | umac data3 > iwlwifi0: 0x00000059 | umac major > iwlwifi0: 0x6B44FA0B | umac minor > iwlwifi0: 0x0046E3BD | frame pointer > iwlwifi0: 0xC0886BAC | stack pointer > iwlwifi0: 0x0036050F | last host cmd TLC; if you were to disable the HT and VHT tunables you either set or the firmware package installed by now you may make it past this, but ... > iwlwifi0: 0x00000000 | isr status reg > iwlwifi0: IML/ROM dump: > iwlwifi0: 0x00000B03 | IML/ROM error/state > iwlwifi0: 0x000051AC | IML/ROM data1 > iwlwifi0: 0x00000090 | IML/ROM WFPM_AUTH_KEY_0 > iwlwifi0: Fseq Registers: > iwlwifi0: 0x60000000 | FSEQ_ERROR_CODE > iwlwifi0: 0x80350002 | FSEQ_TOP_INIT_VERSION > iwlwifi0: 0x00150002 | FSEQ_CNVIO_INIT_VERSION > iwlwifi0: 0x0000A482 | FSEQ_OTP_VERSION > iwlwifi0: 0x00000003 | FSEQ_TOP_CONTENT_VERSION > iwlwifi0: 0x4552414E | FSEQ_ALIVE_TOKEN > iwlwifi0: 0x00080400 | FSEQ_CNVI_ID > iwlwifi0: 0x00000501 | FSEQ_CNVR_ID > iwlwifi0: 0x00080400 | CNVI_AUX_MISC_CHIP > iwlwifi0: 0x00000501 | CNVR_AUX_MISC_CHIP > iwlwifi0: 0x05B0905B | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM > iwlwifi0: 0x0000025B | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR > iwlwifi0: 0x00150002 | FSEQ_PREV_CNVIO_INIT_VERSION > iwlwifi0: 0x00350002 | FSEQ_WIFI_FSEQ_VERSION > iwlwifi0: 0xEFA7B0C2 | FSEQ_BT_FSEQ_VERSION > iwlwifi0: 0x000000C8 | FSEQ_CLASS_TP_VERSION > iwlwifi0: UMAC CURRENT PC: 0x804a228c > iwlwifi0: LMAC1 CURRENT PC: 0xd0 > iwlwifi0: WRT: Collecting data: ini trigger 4 fired (delay=0ms). > iwlwifi0: FW error in SYNC CMD LINK_CONFIG_CMD > #0 0xffffffff80dc58cb at linux_dump_stack+0x1b > #1 0xffffffff8322f7bb at iwl_trans_pcie_send_hcmd+0x44b > #2 0xffffffff831c0318 at iwl_trans_send_cmd+0x88 > #3 0xffffffff8320a649 at iwl_mvm_send_cmd_pdu+0x49 > #4 0xffffffff8320d7d5 at iwl_mvm_link_changed+0x2a5 > #5 0xffffffff83211942 at iwl_mvm_mld_link_info_changed+0x432 > #6 0xffffffff80db457c at lkpi_sta_assoc_to_run+0x53c ^^^^^^ can you look that one up for me. There are two lkpi_80211_mo_bss_info_changed() calls in that function, which one is it? > #7 0xffffffff80dbe853 at lkpi_iv_newstate+0x3c3 > #8 0xffffffff80cea81e at ieee80211_newstate_cb+0x11e > #9 0xffffffff80bb3a62 at taskqueue_run_locked+0x182 > #10 0xffffffff80bb4c32 at taskqueue_thread_loop+0xc2 > #11 0xffffffff80b04e5b at fork_exit+0x7b > #12 0xffffffff8102924e at fork_trampoline+0xe > iwlwifi0: Failed to send LINK_CONFIG_CMD (action:2): -5 > iwlwifi0: failed to update link > iwlwifi0: Failed to send MAC_CONFIG_CMD (action:2): -5 > iwlwifi0: failed to update MAC 0xfffffe00f8c1fedeM > wlan0: link state changed to UP > bad state = 0 > iwlwifi0: Failed to send flush command (-5) > iwlwifi0: flush request fail > wlan0: link state changed to DOWN > bad state = 0 > iwlwifi0: Failed to trigger RX queues sync (-5) > iwlwifi0: Failed to send rate scale config (-5) > iwlwifi0: Couldn't send the SESSION_PROTECTION_CMD: -5 > iwlwifi0: Failed to synchronize multicast groups update > iwlwifi0: Failed to send flush command (-5) > iwlwifi0: Failed to send MAC_CONFIG_CMD (action:2): -5 > iwlwifi0: failed to update MAC 0xfffffe00f8c1fedeM > iwlwifi0: Failed to send LINK_CONFIG_CMD (action:2): -5 > iwlwifi0: Failed to send LINK_CONFIG_CMD (action:3): -5 > iwlwifi0: Failed to send LINK_CONFIG_CMD (action:1): -5 > iwlwifi0: PHY ctxt cmd error. ret=-5 > iwlwifi0: Scan failed! ret -5 > iwlwifi0: ERROR: lkpi_ic_scan_start: hw_scan returned -5 > iwlwifi0: Scan failed! ret -5 > iwlwifi0: ERROR: lkpi_ic_scan_start: hw_scan returned -5 > iwlwifi0: Scan failed! ret -5 > iwlwifi0: ERROR: lkpi_ic_scan_start: hw_scan returned -5 > iwlwifi0: Scan failed! ret -5 > iwlwifi0: ERROR: lkpi_ic_scan_start: hw_scan returned -5 > iwlwifi0: Scan failed! ret -5 > iwlwifi0: ERROR: lkpi_ic_scan_start: hw_scan returned -5 > iwlwifi0: Scan failed! ret -5 > iwlwifi0: ERROR: lkpi_ic_scan_start: hw_scan returned -5 > iwlwifi0: Scan failed! ret -5 > iwlwifi0: ERROR: lkpi_ic_scan_start: hw_scan returned -5 > iwlwifi0: Scan failed! ret -5 > iwlwifi0: ERROR: lkpi_ic_scan_start: hw_scan returned -5 > > Best regards, > Bapt > -- Bjoern A. Zeeb r15:7help
Want to link to this message? Use this
URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?8421106s-4820-2r9q-o48p-441o243p79qp>