Date: Fri, 27 Dec 2002 00:13:18 -1000 (HST) From: "Aaron K. Namba" <anamba@colossus.namba1.com> To: Kirill Bezzubets <kirill@solaris.ru> Cc: freebsd-mobile@FreeBSD.ORG Subject: Re: audio on inspiron 3200 Message-ID: <20021227000826.V46076-100000@colossus.namba1.com> In-Reply-To: <20021227072457.GA88164@solaris.ru>
next in thread | previous in thread | raw e-mail | index | archive | help
Hey, the new kernel config line seems to have worked. Also made a BIOS
change... didn't see a full-duplex option but did change it from
bios-configured to PnPOS.
Now I have other problems, but I've gotten far enough to move the
discussion off this list. Of course, your suggestions are still welcome...
Running mixer returns what I expect, but xmms says ** WARNING **:
oss_open(): Failed to open audio device (/dev/dsp): Device busy.
If the dmesg output is still of interest, here it is:
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.7-STABLE #0: Thu Dec 26 23:32:36 HST 2002
root@colossus.namba1.com:/usr/obj/usr/src/sys/rogue01
Calibrating clock(s) ... TSC clock: 232513155 Hz, i8254 clock: 1193110 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium II/Pentium II Xeon/Celeron (232.53-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x650 Stepping = 0
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 67108864 (65536K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00419000 - 0x03ff7fff, 62779392 bytes (15327 pages)
avail memory = 61358080 (59920K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f6820
bios32: Entry = 0xfd810 (c00fd810) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x203
pnpbios: Found PnP BIOS data at 0xc00f6850
pnpbios: Entry = f0000:b144 Rev = 1.0
pnpbios: Event flag at 4b4
Other BIOS signatures found:
ACPI: 00000000
Preloaded elf kernel "kernel" at 0xc03f2000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc03f20a8.
Preloaded elf module "splash_bmp.ko" at 0xc03f20f8.
Preloaded elf module "vesa.ko" at 0xc03f219c.
Preloaded splash_image_data "/boot/splash.bmp" at 0xc03f2238.
VESA: information block
56 45 53 41 00 02 1f 01 00 01 00 00 00 00 22 00
00 01 1f 00 0c 01 00 01 00 01 09 01 00 01 1a 01
00 01 00 01 01 01 02 01 03 01 04 01 05 01 0d 01
0e 01 10 01 11 01 12 01 13 01 14 01 15 01 16 01
VESA: 22 mode(s) found
VESA: v2.0, 1984k memory, flags:0x0, mode table:0xc03a4282 (1000022)
VESA: MagicGraph 128XD 40K SVGA BIOS
VESA: NeoMagic MagicGraph 128XV 01.0
Pentium Pro MTRR support enabled
Creating DISK md0
md0: Malloc disk
splash: image@0xc03a5448, size:308278
bmp_start(): splash_mode:257
splash: image decoder found: splash_bmp
pci_open(1): mode 1 addr port (0x0cf8) is 0x80001014
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71928086)
Using $PIR table, 3 entries at 0xc00fdf90
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX host to PCI bridge (AGP disabled)> on motherboard
found-> vendor=0x8086, dev=0x7192, revid=0x02
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base 00000000, size 26
found-> vendor=0x10c8, dev=0x0004, revid=0x01
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=255
map[10]: type 1, range 32, base fd000000, size 24
map[14]: type 1, range 32, base fea00000, size 21
map[18]: type 1, range 32, base fed00000, size 20
found-> vendor=0x104c, dev=0xac15, revid=0x01
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=255
found-> vendor=0x104c, dev=0xac15, revid=0x01
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=0 secondarybus=0
intpin=b, irq=255
found-> vendor=0x8086, dev=0x7110, revid=0x02
class=06-80-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7111, revid=0x01
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000fcf0, size 4
found-> vendor=0x8086, dev=0x7112, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=255
found-> vendor=0x8086, dev=0x7113, revid=0x02
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[90]: type 1, range 32, base 00002180, size 4
pci0: <PCI bus> on pcib0
pci0: <NeoMagic MagicGraph 128XD SVGA controller> (vendor=0x10c8, dev=0x0004) at 2.0
pci_cfgintr_unique: hard-routed to irq 11
pci_cfgintr: 0:4 INTA routed to irq 11
pcic0: <TI PCI-1131 PCI-CardBus Bridge> irq 11 at device 4.0 on pci0
pcic0: PCI Memory allocated: 0x88000000
pcic0: TI113X PCI Config Reg: [speaker enable][CSC serial isa irq]
pcic0: PCI Configuration space:
0x00: 0xac15104c 0x02000003 0x06070001 0x00820000
0x10: 0x88000000 0x02000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x0760010b
0x40: 0x007e1028 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00241020 0x00000000 0x00000000 0x00000000
0x90: 0x00743a00 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pccard0: <PC Card 16-bit bus (classic)> on pcic0
pci_cfgintr_linked: linked (61) to hard-routed irq 11
pci_cfgintr: 0:4 INTB routed to irq 11
pcic1: <TI PCI-1131 PCI-CardBus Bridge> irq 11 at device 4.1 on pci0
pcic1: PCI Memory allocated: 0x88001000
pcic1: TI113X PCI Config Reg: [speaker enable][CSC serial isa irq]
using shared irq11.
pcic1: PCI Configuration space:
0x00: 0xac15104c 0x02000003 0x06070001 0x00820000
0x10: 0x88001000 0x02000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x0760020b
0x40: 0x007e1028 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00241020 0x00000000 0x00000000 0x00000000
0x90: 0x00743a00 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pccard1: <PC Card 16-bit bus (classic)> on pcic1
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xfcf0-0xfcff at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xfcf0
ata0: mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ata0-master: ATA 01 a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xfcf8
ata1: mask=03 ostat0=50 ostat2=00
ata1-master: ATAPI 14 eb
ata1-slave: ATAPI 26 ff
ata1: mask=03 stat0=10 stat1=00
ata1: devices=04
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> (vendor=0x8086, dev=0x7112) at 7.2
chip1: <Intel 82371AB Power management controller> port 0x2180-0x218f at device 7.3 on pci0
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
pcic-: pcic0 exists, using next available unit number
pcic-: pcic1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0
ata2 failed to probe at port 0x1f0 irq 14 on isa0
ata3 failed to probe at port 0x170 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x700ff
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 05 f0 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
mss_detect - chip revision 0x0a
mss_detect() - Detected CS4236
pcm0: <CS4236> at port 0x52c-0x533,0xf8c-0xf94,0xe0e irq 5 drq 1 flags 0xa110 on isa0
pcm0: sndbuf_setmap 9000, 1000; 0xc59ee000 -> 9000
pcm0: sndbuf_setmap a000, 1000; 0xc59ef000 -> a000
pcic2 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic3: not probed (disabled)
ed0 failed to probe at port 0x280-0x29f iomem 0xd8000 irq 10 on isa0
isa_probe_children: probing PnP devices
pcic1: Event mask 0x6
BIOS Geometries:
0:03df7f3f 0..991=992 cylinders, 0..127=128 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
bpf: faith0 attached
ad0: success setting UDMA2 on Intel chip
Creating DISK ad0
ar: FreeBSD check1 failed
ad0: <FUJITSU MHC2040AT/0818> ATA-3 disk at ata0-master
ad0: 3909MB (8007552 sectors), 7944 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=2 cblid=0
ata1-master: piomode=4 dmamode=2 udmamode=-1 dmaflag=1
ata1-master: success setting PIO4 on generic chip
acd0: <TOSHIBA CD-ROM XM-1702BC/1854> CDROM drive at ata1 as master
acd0: read 4134KB/s (34515KB/s), 128KB buffer, PIO4
acd0: Reads: CD-R, CD-RW, CD-DA stream
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
Mounting root from ufs:/dev/ad0s1a
ad0s1: type 0xa5, start 63, end = 8007551, size 8007489 : OK
start_init: trying /sbin/init
pcic1: Autodetected 5.0V card
pccard: card inserted, slot 1
pcic1: reset 1 int is 10 stat is 6f
pccard: card removed, slot 1
pcic1: reset 1 int is 10 stat is 6f
pcic1: Autodetected 5.0V card
pccard: card inserted, slot 1
pcic1: reset 2 pcic1: Event mask 0x9
int is 70 stat is 4f
pcic1: reset 3 int is 70 stat is 6f
pcic1: reset 0
pccard1: Assigning wi0: io 0x240-0x27f irq 11 mem 0x0-0xffffffff
pcic: I/O win 0 flags 15 240-27f
wi0: Forcing IRQ to 11
pcic: I/O win 0 flags 5 240-27f
wi0 at port 0x240-0x27f irq 11 slot 1 on pccard1
pcic: I/O win 0 flags 15 240-27f
wi0: Forcing IRQ to 11
wi0: 802.11 address: 00:06:25:aa:b1:73
wi0: using RF:PRISM3(PCMCIA)
wi0: Intersil Firmware: Primary 1.00.07, Station 1.03.05
wi0: wi_has_wep = 1
bpf: wi0 attached
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> at device 7.2 on pci0
uhci0: Could not map ports
device_probe_and_attach: uhci0 attach returned 6
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> at device 7.2 on pci0
uhci0: Could not map ports
device_probe_and_attach: uhci0 attach returned 6
Linux ELF exec handler installed
On Fri, 27 Dec 2002, Kirill Bezzubets wrote:
> On Thu, Dec 26, 2002 at 09:01:08PM -1000, Aaron K. Namba wrote:
>
> > Okay, I've tried everything google can find me on how to configure the
> > audio on my Inspiron 3200. As far as I can tell, it is a Crystal 4237B,
> > but all the things that are supposed to work just don't do anything. I
> > checked the BIOS, I don't think there's anything suspect there...
>
> Actually, I never tried it on Inspirons, but my Latitude has 4237B too,
> and former Dell guys say there's more similarity than usual.
> So, maybe, I could help you.
>
> Is your card set in "Full Duplex" mode in BIOS?..
>
> >
> > This is my first time trying to configure audio that didn't get detected
> > in GENERIC, so please help...
> >
> >
> > This kernel config doesn't work:
> > device pcm
> > device csa
> >
>
> It won't - card you have isn't PnP.
>
> > This kernel config hangs the machine as gnome is starting:
> > device pcm0 at isa? port 0x52c irq 5 drq 1 flags 0x13
>
> Try this one:
>
> device pcm0 at isa? port 0x52c irq 5 drq 1 flags 0x10
>
> And could you send dmesg output from "boot -v" ?
>
> --
> BR,
> Kirill Bezzubets CASE-RIPE CASE-RIPN
> Senior Administrator, Technical Department mailto:kirill@solaris.ru
> Solaris ISP & Telecommunications Co. Ltd http://www.solaris.ru
>
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20021227000826.V46076-100000>